DeWalt DCW210 Instruction Manual
20v max* 5" (127 mm) random orbit palm sander
Hide thumbs
Also See for DCW210:
- Original instructions manual (145 pages) ,
- Instruction manual (41 pages) ,
- Manual (14 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for DeWalt DCW210
Summary of Contents for DeWalt DCW210
- Page 1 Instruction Manual DCW210 20V Max* 5" (127 mm) Random Orbit Palm Sander...
- Page 2 Definitions: Safety Alert Symbols and Words This instruction manual uses the following safety alert symbols and words to alert you to hazardous situations and your risk of personal injury or property damage. DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
-
Page 3: General Power Tool Safety Warnings
GENERAL POWER TOOL SAFETY WARNINGS protection used for appropriate conditions will reduce personal injuries. WARNING! Read all safety warnings and all c ) Prevent unintentional starting. Ensure the instructions. Failure to follow the warnings and switch is in the off-position before connecting instructions may result in electric shock, fire and/or to power source and/or battery pack, picking up serious injury. -
Page 4: Additional Safety Instructions For Sanders
work to be performed. Use of the power tool for Empty dust bag frequently, especially when sanding • operations different from those intended could result resin coated surfaces such as polyurethane, varnish, in a hazardous situation. shellac, etc. Dispose of coated dust particles according to the finish manufacturer’s guidelines, or place in a metal h ) Keep handles and grasping surfaces dry, clean and free from oil and grease. -
Page 5: Batteries And Chargers
buildings in summer). For best life store battery packs in The label on your tool may include the following symbols. The symbols and their definitions are as follows: a cool, dry location. NOTE: Do not store the battery packs in a tool with V ...... - Page 6 The RBRC® Seal shipping Mode: When the cap is attached to the The RBRC® (Rechargeable Battery FLEXVOLT™ battery, the Recycling Corporation) Seal on the nickel battery is in Shipping Mode. cadmium, nickel metal hydride or lithium- Strings of cells are ion batteries (or battery packs) indicates electrically disconnected within the pack resulting in three that the costs to recycle these batteries...
-
Page 7: Charger Operation
gauge. An undersized cord will cause a drop in line voltage be shorted by foreign material. Foreign materials of a conductive nature, such as, but not limited to, resulting in loss of power and overheating. When using grinding dust, metal chips, steel wool, aluminum more than one extension to make up the total length, foil or any buildup of metallic particles should be be sure each individual extension contains at least the... -
Page 8: Electronic Protection System
nOTE: This could also mean a problem with a charger. 2. The charger and battery pack may become warm to the touch while charging. This is a normal condition, and If the charger indicates a problem, take the charger and does not indicate a problem. To facilitate the cooling of battery pack to be tested at an authorized service center. -
Page 9: Assembly And Adjustments
To Attach the Dust Bag (Fig. E) with an 8-hole dust extraction pattern. Sanding discs for the 1. While holding the sander, fit the dust bag collar 5 DCW210 attach with hook and loop. the dust port as shown in Figure E. 3 ... -
Page 10: Installing And Removing The Battery Pack
Installing and Removing the Battery Pack NOTICE: Avoid overloading your sander. Overloading will result in a considerable reduction in speed and (Fig. F) finish quality of your work. The unit may also become nOTE: For best results, make sure your battery pack is hot. -
Page 11: Maintenance
Sanding should be done in a manner to reduce Fig. H tracking of paint dust outside the work area. 3. ClEAning AnD DisPOsAl All surfaces in the work area should be vacuumed and thoroughly cleaned daily for the duration of the sanding project. Vacuum filter bags should be changed frequently.