Advertisement
Quick Links
Rear Roller Brush MVP Kit
Reelmaster
and Universal Groomer
Model No. 133-0152
This product complies with all relevant European directives. For details, please see the Declaration of
Incorporation (DOI) at the back of this publication.
Installation
Loose Parts
Use the chart below to verify that all parts have been shipped.
Description
No parts required
Roller-brush assembly
Retaining ring
Drive-housing assembly
90-degree grease fitting
Carriage bolt
Weight
Locknut
Drive pulley
Hex-drive bolt (5/16 x 1/2 inch)
Belt
Shim washer (as required for belt alignment)
Drive cover
Bumper plate
Belt-alignment tool
High height-of-cut brush (optional)
Front bumper assembly (sold separately)
Washer
Rear bumper assembly (sold separately)
© 2019—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
3550 Series 18-inch Cutting Unit with 5-inch Reel
Qty.
Determine the position of the roller brush and the reel
–
motor.
1
1
1
1
2
2
2
Install the kit.
1
7
1
1
1
1
1
Install the high height-of-cut brush—for HOC greater than
—
2.5 cm (1 inch).
1
Install the front bumper assembly.
2
1
Install the rear bumper assembly.
Register at www.Toro.com.
Form No. 3399-406 Rev C
Installation Instructions
Use
Original Instructions (EN)
All Rights Reserved *3399-406* C
Printed in the USA
Advertisement
Related Manuals for Toro 133-0152
Summary of Contents for Toro 133-0152
- Page 1 ® 3550 Series 18-inch Cutting Unit with 5-inch Reel and Universal Groomer Model No. 133-0152 Installation Instructions This product complies with all relevant European directives. For details, please see the Declaration of Incorporation (DOI) at the back of this publication.
- Page 2 Installing the Kit Note: Install the universal groomer kit first; refer to the groomer installation instructions. Important: Use the Rear Roller Brush Kit only Installing the Grease Fitting when cutting in the height-of-cut range of 6 to 25 mm (1/4 to 1 inch). Use the high height-of-cut Remove the grease fitting for the roller from the brush when cutting above 25 mm (1 inch).
- Page 3 Installing the Weights Install the weights to the cutting unit as shown in Figure g283859 Figure 4 1. Carriage bolts (5/16 x 1 3. Weights g035576 Figure 5 inch) 2. Flange nuts (5/16 inch), 1. Left roller-brush assembly 2. Roller-brush mounting torque to 20 to 26 N∙m (15 bracket to 19 ft-lb)
- Page 4 Installing the Roller-Brush Housing Remove and discard the groomer drive cap. g283858 Figure 7 1. Cap g033201 Figure 6 Install the left or right roller-brush housing (Figure 1. Bearing housing 2. Excluder seal Note: Ensure that the idler-pulley assembly is installed on the bottom as shown in Figure g033300...
- Page 5 To change the idler-pulley assembly to a Apply 242 Loctite (blue) to the 2 bolts (5/16 x right-drive configuration, refer to Figure 1/2 inch) and use them to mount the roller-brush housing to the bearing housing (Figure Note: Torque the bolts to 20 to 26 N∙m (15 to 19 ft-lb).
- Page 6 Positioning the Roller Brush Installing the Drive Pulley Loosen the 2 bolts securing each Restrain the reel for installation; refer to roller-brush-bearing housing to the roller-brush Restraining the Reel for Installing Threaded mounting bracket (Figure 10). Inserts (page 12). Install the drive pulley onto the groomer shaft Note: The bolts should be loose from the (Figure...
-
Page 7: Installing The Belt
Installing the Belt Push down on the idler pulley to ensure that the idler-pulley assembly pivots freely. Install the belt onto the pulleys as follows: • Loop the belt around the drive pulley and Completing the Installation then over the top of the idler pulley (Figure 13). - Page 8 Installing the High Clamp the brush onto the shaft with the 2 J-bolts and nuts previously removed (Figure 19). Height-of-Cut Brush Important: Insert the threaded end of the (Optional) J-bolts through the outer holes of the brush shaft while hooking the curved ends of the J-bolts into the inner holes.
-
Page 9: Maintenance
Installing the Front Bumper Installing the Rear Bumper Assembly (Cutting Units 1 Assembly (Cutting Units 2 and 4 Only; Optional) and 3 Only; Optional) Lower the cutting units to the ground. Install the rear bumper assembly as shown in . Remove the existing flange-head bolts and the round bumpers (Figure... - Page 10 Checking the Pulley Alignment Important: Ensure that the belt is properly tensioned prior to checking the alignment. Lay a straightedge along the outer face of the drive pulley (Figure 23). Important: Only lay the straightedge across the drive pulley, do not lay it across the drive and the driven pulley.
- Page 11 Important: While holding the flats of the roller-brush shaft, Ensure that the ribs on the belt secure the driven pulley on the shaft with the are properly seated in the grooves in each flange nut (3/8–16) previously removed. pulley and that the belt is in the center of the idler pulley.
- Page 12 Restraining the Reel for Installing Threaded Inserts Insert a long-handled pry bar (recommended 3/8 x 12 inch with screwdriver handle) through the front of the cutting reel, closest to the side of the cutting unit that you will be torquing (Figure 29).
- Page 13 Notes:...
- Page 14 Notes:...
- Page 15 Notes:...
- Page 16 The method of transmission shall be electronic transmittal. This machinery shall not be put into service until incorporated into approved Toro models as indicated on the associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in conformity with all relevant Directives.