Advertisement
Quick Links
CE Conversion Kit
24in Stand-On Aerator
Model No. 135-7423
Safety
Safety and Instructional
Decals
Safety decals and instructions are
easily visible to the operator and are
located near any area of potential
danger. Replace any decal that is
damaged or missing.
135-3183
1. Bypass lever position for
pushing the machine.
2. Read the instructions
before servicing or
performing maintenance.
© 2021—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
decal135-3183
3. Bypass lever position for
operating the machine.
Register at www.Toro.com.
Installation
1
Preparing the Machine
No Parts Required
Procedure
1.
Park the machine on a level surface and engage
the parking brake.
2.
Shut off the engine and remove the key.
3.
Wait for all moving parts to stop.
4.
Allow the machine to cool.
5.
Disconnect the spark plug; refer to the
Operator's Manual for your machine.
2
Removing the Covers and
Guards
No Parts Required
Removing the
Hydraulic-Component Covers
1.
Remove 2 thumbscrews that secure the
hydraulic-component cover to the machine, and
remove the cover
Note:
Discard the covers and thumbscrews.
Original Instructions (EN)
Printed in the USA
All Rights Reserved
Form No. 3433-517 Rev F
Installation Instructions
(Figure
1).
*3433-517*
Advertisement
Related Manuals for Toro 135-7423
Summary of Contents for Toro 135-7423
- Page 1 Form No. 3433-517 Rev F CE Conversion Kit 24in Stand-On Aerator Model No. 135-7423 Installation Instructions Safety Installation Safety and Instructional Decals Preparing the Machine Safety decals and instructions are easily visible to the operator and are located near any area of potential danger.
- Page 2 g349556 Figure 1 Left side shown 1. Right 3. Left hydraulic-component hydraulic-component cover cover 2. Thumbscrews 4. Cover mount brackets g293458 Figure 2 Repeat step for the other hydraulic-component Left side shown cover. 1. Carriage bolt 4. Chain guard 2. Washer 5.
- Page 3 Assembling the Chain Guards Assemble 2 flange-head capscrew (10 x 35 mm) through the hole into the hydraulic-component cover (Figure Preparing the Covers and Guards Parts needed for this procedure: Left CE hydraulic-component cover Right CE hydraulic-component cover Flange-head capscrew (3/8 x 1 inch) Retaining ring (3/8 inch) Left CE chain guard Right CE chain guard...
- Page 4 Assembling the Rear Platform Cover Assemble 2 flange-head capscrews (3/8 x 1 inch) through the holes into the rear platform cover (Figure 6) that you removed in Removing the Rear Platform Cover (page g349606 Figure 7 1. Flange locknut (3/8 inch) 3.
- Page 5 g349610 Figure 8 1. Right 3. Left hydraulic-component g349720 hydraulic-component cover Figure 9 cover 2. Flange-head capscrew 4. Full-threaded bolt (3/8 x 2 1. Clip nuts (10 mm) 2. Guard mount (3/8 x 1 inch) inches) Repeat step at the other side of the machine. Align the slot in the hydraulic-component cover At the bottom of the machine, assemble a with the full-threaded bolt (3/8 x 2 inches).
- Page 6 g349723 g349721 Figure 11 1. Front of the Machine 3. Right side of the machine 2. Left side of the machine Installing the Chain Guards g349722 Figure 10 Align the flange-head bolts of the CE chain guard with the clip nuts and threaded spacer on 3.
- Page 7 g349739 Figure 14 1. Mounting flange (frame) 3. Rear platform cover 2. Flange-head capscrew (3/8 x 1 inch) Loosely assemble the cover to the flanges with the capscrews. Torque the flange-head capscrews to 37 to 45 N∙m (27 to 33 ft-lb). g349736 Figure 13 1.
- Page 8 Installing the Decals Finishing Installing the Kit Parts needed for this procedure: No Parts Required Decal 133-5623 (machine manufacturer date) Procedure Decal 142-2156 (CE sound) Connect the spark plug; refer to the Operator’s Manual for your machine. Procedure Install decals 133-5623 (machine manufacturer date) and 142-2156 (CE sound) to the left frame plate as shown in Figure...