Do you have a question about the WHKF-DWHV and is the answer not in the manual?
Questions and answers
glen weber
March 21, 2025
i just bought the filter and can't remove the filter housing..suggestions
1 comments:
Mr. Anderson
March 21, 2025
To remove the filter housing for the Whirlpool WHKF-DWHV filter, follow these steps:
1. Turn Off Water Supply – Shut off the water by turning the valve on the filter head to the "OFF" or "BYPASS" position. 2. Place a Bucket Underneath – Position a bucket under the filter to catch any water that may spill out. 3. Unscrew the Housing – Use a wrench if needed to loosen and remove the housing. 4. Remove the Old Cartridge – Take out the old filter cartridge. 5. Clean the Housing – Wash the housing thoroughly with mild soap and water before installing a new filter.
These steps ensure a safe and clean removal process.
Page 1
Installation, Use & Care Guide Filtration pour maison entière système standard avec robinet d’arrêt Guide d’installation, d’utilisation et d’entretien Filtración para toda la casa sistema estándar con válvula de cierre Guía de instalación, uso y cuidado Model / Modèle / Modelo : WHKF-DWHV W10180036...
Teflon Tape Adjustable Wrench ® 5. Install Whirlpool Grounding Kit WHKF-GRND, sold separately, in metal water piping systems (see Figure 3). Installation Requirements IMPORTANT: Metal water piping systems are required to be connected to the electrical ground. To maintain the Properly tighten all fittings to ensure a leak-free assembly.
“Using Push-In Fittings” p.m. (EST) To Attach Tubing or write us at: Push tubing in as far as it will Whirlpool Water Products go. Tubing must be inserted Customer eXperience Center past o-ring and hit backstop. 553 Benson Road Pull tube to ensure it is secured.
Specifications System Tested and Certified by NSF International against NSF/ANSI Standard 42 for Model: DWHV (For use with replacement the reduction of Particulate Class V. cartridge WHKF-GD05) Min./Max. Temperature: 40-100° F Min./Max. Operating Pressure: 25-100 psi Flow Rate: 6 GPM Capacity: N/A 1 Year Limited Warranty upon the return of the defective product to KEMFLO...
Outils et pièces requis mise à la terre WHKF- Figure 2 GRND de Whirlpool, vendu Rassemblez les outils requis avant de commencer séparément, dans les l’installation. Bien lire et suivre les instructions fournies avec systèmes de conduits en métal (voir la Figure 3).
b. Connectez le fil de mise à la terre aux deux serres de Remplacement du filtre mise à la terre, à l’aide du terminal à vis sur chaque serre de mise à la terre. Serrez solidement. Les contaminants ou autres substances enlevées ou réduites 6.
Page 7
18h00 (HNE) Température min. / max. : 4,4° à 37,8˚ C ou écrivez-nous à : Pression d’opération Whirlpool Water Products min. / max. : 25 à 100 psi Customer eXperience Center 553 Benson Road Débit nominal : 22,7 litres par minute Benton Harbor, MI 49022-2692 Capacité...
WHKF-GRND al contactar la tienda donde compró la carcasa. la cabeza del filtro o contacte a Whirlpool por el 1-866- 363-9472. Instale el filtro lejos de la luz solar, pues su exposición prolongada podría debilitar los componentes plásticos.
b. Conecte el cable de puesta a tierra a las dos Reemplazo del filtro abrazaderas de puesta a tierra, mediante la terminal del tornillo metálico, que se encuentra en cada abrazadera Los contaminantes u otras sustancias eliminadas o reducidas de puesta a tierra. Sujete firmemente. por este filtro de agua no están necesariamente en el agua de 6.
Estados Unidos y Canadá al 1-866-363-9472, de lunes a Especificaciones viernes de 8:00 a.m. a 6:00 p.m., hora del Este, o puede escribirnos a Modelo: DWHV (Para usar con el cartucho Whirlpool Water Products de reemplazo WHKF-GD05) Customer eXperience Center Temperatura mín./máx.: 4,4°-37,8° C 553 Benson Road Presión de operación...
Need help?
Do you have a question about the WHKF-DWHV and is the answer not in the manual?
Questions and answers
i just bought the filter and can't remove the filter housing..suggestions
To remove the filter housing for the Whirlpool WHKF-DWHV filter, follow these steps:
1. Turn Off Water Supply – Shut off the water by turning the valve on the filter head to the "OFF" or "BYPASS" position.
2. Place a Bucket Underneath – Position a bucket under the filter to catch any water that may spill out.
3. Unscrew the Housing – Use a wrench if needed to loosen and remove the housing.
4. Remove the Old Cartridge – Take out the old filter cartridge.
5. Clean the Housing – Wash the housing thoroughly with mild soap and water before installing a new filter.
These steps ensure a safe and clean removal process.
This answer is automatically generated
How to turn black handle on filter system