Related Manuals for Whirlpool WSR413YW0
Summary of Contents for Whirlpool WSR413YW0
- Page 1 ChIJ Inst’dfat ion Instructions WHIRLPOOL UNDERCOUNTER OSMOSIS REVERSE WATER FILTRATION SYSTEM IV...
- Page 2 16 pounds . l/4” drill bit - safety glasses - Basement Installation Part No. 4373517 available from your Whirlpool dealer. J/ : 3 %s” wrench or Kit, Open This Flap For Installation Overview...
-
Page 3: Connect Tubing
14 additional feet of tubing should be used. Order Basement Installation Kit, Part No. 4373517 from your Whirlpool dealer and follow the kit instructions. DO NOT use filtration system if water is microbiologically unsafe or water quality is unknown. - Page 4 Instructions At A Glance For detailed instructions see following page. 1. Turn off cold water supply. (Steps la-lb) 2. Turn on faucet to drain water from line. (Step 1 b) 3. Connect saddle valve to cold water supply. 4. Turn saddle valve handle clockwise until piercing (Steps We or 1 h-lj) lance enters pope and stops.
- Page 5 Product Damage DO NOT connect to a hot water supply line. Failure to follow this instruction could result in product damage. Take note of water requirements listed . under the Use & Care section of this booklet. The filtration system’s feed line (orange tubing) connects to your cold water supply line using the saddle valve.
- Page 6 nstructions see following page. Instructions At A Glance For detailed 2. Connect green tubing and black tubing I. Connect faucet spout, chrome base plate, indicator light to faucet. (Steps 2c-2d) disk and rubber washer to faucet base. (Steps 2a-2b) 4. Connect faucet indicator wire to wire harness 3.
- Page 7 Front view of air gap faucet _ chrome base elate indicator light wire ;fby;; Fhex %” grey connector with push-in Side view of air gap faucet spout air gap hole slnk %” tubing black %” tubing must ;lor; downward blue %” tubing Property Damage...
- Page 8 Instructions At A Glance 1. Install RO cartridge into filtration assembly. Connect one end of red tubing to bottom of RO cartridge. Connect other end to green tubing from faucet. (Steps 3a-3e) 3. Use orange tubing from filtration assembly to fill storage tank with water.
- Page 9 (mounted to wood floor supports or to the basement wall). For basement installation order Basement Installation Kit, Part No. 4373517 available from your Whirlpool dealer. Property/Product Damage DO NOT store or o...
- Page 10 Instructions At A Glance For detailed instructions see following page. 1. Decide where drain saddle will be mounted. 2. Connect drain saddle to drain pipe. (Step 4c) The best place is on a horizontal drain tailpiece I above (before) the trap. (Steps 4a-4b) 3.
- Page 11 Electrical Shock Hazard Special care must be taken when drilling into water pipes. Some water may remain in pipe. - If an electric drill is used, it must be properly grounded to prevent severe or lethal shock if water should enter drill. Use only an electric drill with a 3-wire power supply cord connected to a grounded receptacle.
-
Page 12: Flush System
Flush System Instructions At A Glance For detailed instructions see following page. I. Slide filtration assembly onto mounting screws. 2. Turn on faucet and drain tank to flush (Step 5a) disinfectant from tank. (Step 5b) 3. Turn on cold water supply and 4. -
Page 13: General Information
Flush System Slide filtration asse . mounting holes onto mounting screws that were installed in step 3b. DO NOT kink or bend tubing. Insulated staples may be used to secure tubing to cabinet walls. Tighten mount- ing screws to secure filtration assembly to wall. -
Page 14: Water Requirements
- replace red tubing with tubing of proper length available from your Whirlpool dealer. Confirm that the water saddle valve is fully open. Check for obstructions in the faucet air gap by removing the air gap and inspecting the flow path - replace faucet if necessary. - Page 15 Using your RO water filtration system To get purified water from the storage tank - Hold the faucet handle down for momentary flow, hold the faucet up for continuous flow. To stop water flow from the faucet - Return the faucet to the center or horizontal position.
- Page 16 How To Arrange For Service... In the event that your Whirlpool appliance should ever need service, call the dealer from whom you purchased the appliance or a Whirlpool-authorized service company. A Whirlpool-authorized service company is listed in the Yellow Pages of your telephone directory under “Appliances-Major-Service...
-
Page 17: Performance Data Sheet
Performance Data Sheet @ Whirlpool Reverse Osmosis Water Filtration System IV Test Parameters TDS = 200500 mg/L2 pH = 7.5 Turbidity = 1 NTU Temperature ‘USEPA Maximum Contaminanl Level or Action Level (mg/L). 3arrium. Cadmium and Chromium were tested at 750 mglL TDS. - Page 18 Whirlpool Corporation Part No. 4373500 Rev B Printed on Recycled Paper in U.S.A. Benton Harbor, MI 49022 01993 Whirlpool Corporation...