Sealey SA291.V3 Quick Start Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear eye
instructions protection
1. SAfETY
Follow all workshop safety rules, regulations and conditions when using wrench.
9
WARNING! disconnect from air supply before changing accessories or servicing.
‰
Maintain the wrench in good condition and replace any damaged or worn parts. Use genuine parts only. Unauthorized parts
9
may be dangerous and will invalidate the warranty.
WARNING! Check correct air pressure is maintained and not exceeded. We recommend 90psi.
‰
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure that all connections are
9
secure.
Only use impact sockets which are specifically designed for use with an impact wrench.
9
Wear approved safety eye/face shield, ear defenders and hand protection.
9
WARNING! due to the possible presence of asbestos dust from brake linings, when working around vehicle brake systems we recommend
‰
you wear suitable respiratory protection.
Maintain correct balance and footing. ensure the floor is not slippery and wear non-slip shoes.
9
Keep children and non essential persons away from the working area.
9
DO NOT use the wrench for a task it is not designed to perform.
8
WARNING! DO NOT use wrench if damaged or thought to be faulty. (Contact Service Agent).
‰
DO NOT use wrench unless you have been instructed in its use by a qualified person.
8
DO NOT carry the wrench by the air hose, or yank the hose from the air supply.
8
DO NOT operate wrench if you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT carry wrench with your finger on the power trigger in order to avoid unintentional starting.
8
DO NOT direct air from the air hose at yourself or others.
8
When not in use disconnect from air supply and store in a safe, dry, childproof location.
9
WARNING! The warnings, cautions and instructions discussed in this manual cannot cover all possible conditions and
‰
situations that may occur. It must be understood that common sense and caution are factors which cannot be built into this
product, but must be applied by the operator.
2. INTRODUCTION
Suitable for heavy commercial tyre shop, fleet and workshop use. Features air/torque device, to control power output, and reverse
action. long pattern anvil gets into deeply dished wheels. Supplied with side handle.
3. SPECIfICATION
drive size ....................................................................... 1"Sq
Working Max torque ................................... 1836nm/1350lb.ft
Ultimate torque......................................................... 1600lb.ft
Free Speed .............................................................. 3500rpm
Weight ......................................................................... 15.2kg
Air consumption .......................................................... 21cfm
operating pressure ....................................................... 90psi
Air inlet size ..............................................................1/2"BSP
noise Power............................................................ 108dB(A)
noise Pressure ......................................................... 97dB(A)
Vibration ............................................................... 12.579m/s²
Uncertainty ................................................................ .1.5m/s²
4. PREPARATION
4.1. AIR SUPPLY
Recommended hook-up procedure is shown in fig 1.
4.1.1. Ensure wrench air valve (or trigger) is in the "off" position before connecting to the air supply.
4.1.2. You will require an air pressure of 90psi and an air flow according to specification.
WARNING! ensure the air supply is clean and does not exceed 90psi while operating the wrench. Too high an air pressure and unclean
‰
air will shorten the product life due to excessive wear and may be dangerous, causing damage and/or personal injury.
4.1.3. drain the air tank daily. Water in the air line will damage the wrench.
© Jack Sealey limited
1" SQ DRIVE EXTRA HEAVY DUTY IMPACT
WRENCH, LONG ANVIL
Model no:
Wear protective Wear safety
gloves footwear
Original Language Version
SA291.V3
Wear protective Wear ear
clothing protection
Wear a mask
SA291.V3 Issue 6 (HF) 11/09/18