Sealey SA29/S.V2 Instructions

ITEM PART NO DESCRIPTION ITEM PART NO
1 SA29SX-01 MOTOR HOUSING 18 SA29SX-18 TRIGGER PIN
2 SA29SX-02 REAR COVER 19 SA29SX-19 BUSHING
3 SA29SX-03 REAR GASKET 20 SA29SX-20 THROTTLE PIN
4 SA29SX-04 SCREW 21 SA29SX-21 O-RING
5 SA29SX-05 WASHER 22 SA29SX-22 RETAINER, O-RING
6 SA29SX-06 ANVIL BUSHING 23 SA29SX-23 SPRING
7 SA29SX-07 OIL SEAL 24 SA29SX-24 SCREEN
8 SA29SX-08 COVER 25 SA29SX-25 HOSE FITTING
9 SA29SX-09 SCREW 26 SA29SX-26 O-RING
10 SA29SX-10 CLUTCH HOUSING 27 SA29SX-27 DUST COVER
28 SA29SX-28 VALVE SLEEVE
11 SA29SX-11 FRONT GASKET
12 SA29SX-12 SCREW 29 SA29SX-29 REVERSE VALVE
13 SA29SX-13 WASHER 30 SA29SX-30 LEVER REVERSE
14 SA29SX-14 SCREW 31 SA29SX-31 PIN
15 SA29SX-15 HANDLE DEAD 32 SA29SX-32 O-RING
16 SA29SX-16 SCREW 33 SA29SX-33 BEARING
17 SA29SX-17 TRIGGER 34 SA29SX-34 FRONT END PLATE
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component
parts without prior notice. IMPORTANT: No liability is accepted for incorrect use of this equipment. WARRANTY: Guarantee is 12
months from purchase date. proof of which will be required for any claim. INFORMATION: Call us for a copy of our latest catalogue
and promotions on 01284 757525 and leave your full name and address including your postcode.
Sole UK Distributor, Sealey Group, Bury St. Edmunds, Suffolk.
01284 757500
Issue : 1
Date : 191203
DESCRIPTION
ITEM PART NO DESCRIPTION
35 SA29SX-35 PIN
36 SA29SX-36 CYLINDER
37 SA29SX-37 ROTOR
38 SA29SX-38 ROTOR BLADE
39 SA29SX-39 REAR END PLATE
40 SA29SX-40 PIN
41 SA29SX-41 HAMMER CAGE
42 SA29SX-42 WASHER
43 SA29SX-43 HAMMER PIN
44 SA29SX-44 HAMMER DOG
45 SA29SX-45 DRIVE CAM
46 SA29SX-46 ANVIL
47 SA29SX-47 BUSHING FLANGE
48 SA29SX-48 WASHER
49 SA29SX-49 O-RING
50 SA29SX-50 ANVIL COLLAR
51 SA29SX-51 O-RING
E-mail: sales@sealey.co.uk
01284 703534
Web: www.sealey.co.uk
INSTRUCTIONS FOR
1” SQUARE DRIVE
AIR IMPACT WRENCH
SA29/S.V2
Model:
Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH
IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE
THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
! Follow all workshop safety rules, regulations, and
1. SAFETY INSTRUCTIONS
conditions when using wrench.
F WARNING! Disconnect from air supply before changing
accessories or servicing.
! Maintain the wrench in good condition and replace
any damaged or worn parts. Use
g e n u i n e p a r t s o n l y. Unauthorised parts may be
dangerous and will invalidate the warranty.
F WARNING! Check correct air pressure is maintained and not exceeded. We recommend 90psi.
! Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each
use and ensure that all connections are secure.
! Only use impact sockets which are specifically designed for use with an impact wrench.
! Wear approved safety eye/face shield, ear defenders, and hand protection.
F WARNING! Due to the possible presence of asbestos dust from brake linings, when working
around vehicle brake systems we recommend you wear suitable respiratory protection.
! Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
! Keep children and non essential persons away from the working area.
% DO NOT use the wrench for a task it is not designed to perform.
F WARNING! DO NOT use wrench if damaged or thought to be faulty. (Contact Service Agent).
% DO NOT use wrench unless you have been instructed in its use by a qualified person.
% DO NOT carry the wrench by the air hose, or yank the hose from the air supply.
% DO NOT operate wrench if you are tired or under the influence of alcohol, drugs or intoxicating medication.
% DO NOT carry wrench with your hand on the power trigger in order to avoid unintentional starting.
% DO NOT direct air from the air hose at yourself or others.
! When not in use disconnect from air supply and store in a safe, dry, childproof location.
2. INTRODUCTION & SPECIFICATIONS
Suitable for commercial and agricultural vehicle use. Long anvil and straight configuration with
rocking-dog clutch for applications with restricted access. Fitted with reverse action. Supplied with
side handle.
Drive size . . . . . . . . . . . . . . . . . . .1”Sq
Working/Max torque . . . . .900/1100ft.lb
Operating pressure . . . . . . . . . . .90psi
Weight . . . . . . . . . . . . . . . . . . . 14.9kg
Sound pressure . . . . . . . . . . .106.8dB
Air inlet size . . . . . . . . . . 1/2” BSP
Ultimate torque . . . . . . . . .1150ft.lb
Air consumption . . . . . . . . . 21cfm
Vibration level . . . . . . . . . .1.5m/s
2
Sound Power . . . . . . . . . .107.5dB
SA29/S.V2 - 1 - 191203