Gtech AirRAM MK2 (AR29) - Cordless Vacuum Manual

Find the Product Serial Number

Make a note of your product serial number code for future reference. You can find this on the underside of item

What's in the box

(Filter, battery and bin are already in place)

1. Head full assembly
2. Lower Handle X 2 components
3. Upper Handle X 2 components
4. Battery
5. Charger
6. Bin
7. Filter

Assembly

To attach the lower handle to the head assembly, insert the metal pin on the lower handle into the hole located on the pivot yoke.
Make sure the green locking clip is unlocked to allow the lower handle to fit.

Ensure the lower handle is sitting completely flush against the yoke. Then push the green locking clip into the back of the head.

Fit the two components of the lower handle together in the orientation shown in the image above. They will only fit together one way. The components will click into place and will remain permanently fixed.

Fit the two components of the Upper Handle together in the orientation shown in the image above. They will only fit together one way. The components will click into place and will remain permanently fixed.

The green locking clip, when correctly fitted, will click and hold the lower handle in place. Should the handle assembly need to be removed the clip can be pulled out to unlock the lower handle.
The green locking clip remains permanently attached to the head assembly.

Insert the upper handle into the lower handle. You will need to press the button on the upper handle to fit it in.
Once it slides down you will hear it click into place.

Storage

To stow or extend the upper handle simply press the button on the lower handle to unlock the upper handle.
The upper handle will now slide up or down depending on required position.

The upper handle can be set in two positions: Lowered for storage and raised for use.
To lower the handle, release the upper button. To raise the handle from the stored position, release the lower button.

Operation

Without pressing the power button, place your foot on the left side of the AirRAM head and pull the handle back.

The power button is located on the left hand side of the AirRAM head assembly.

Press the power button with your foot to turn the AirRAM on.

Battery charging

When the state of charge indicator starts to flash one green LED, recharge the battery.

The battery can be charged whilst it's in the AirRAM, or when it's off the product. To remove the battery, squeeze the latch underneath and pull upwards.

Plug the charger into the mains and connect it to the battery. Switch on at the mains.

The battery can be charged from flat in 4 hours. The state of charge indicator will show 4 solid green lights when it is charged. It is OK to charge for 1 hour for a burst of cleaning. Replace the battery by sliding it down into the head assembly. It will click into place.

Emptying the bin

Holding onto the AirRAM with one hand, pull the bin handle and lift the bin out of the AirRAM.

Lift and release the latch marked with the green arrow to pull open the lid.

Hold the AirRAM's bin over a rubbish bin and push the green lever towards the lid to empty the dirt.

Pull the green lever back towards the bottom of the bin. Close the bin lid and reinsert the bin into the AirRAM.

Cleaning the filters

Do this once a month or more frequently depending on use.

Holding onto the AirRAM with one hand, pull the bin handle and lift the bin out of the AirRAM.

Pull the filter out of the filter housing. Tap the dirt from the filter and tip any dirt from the filter housing. Wash the filter if necessary.

Remove the filter from the inner shroud, by twisting and pulling. Tap the inner shroud over a bin to remove any excess dirt.

Wash the filter under a tap. Squeeze out any excess water then let it dry completely before reinserting into the AirRAM. Recommended water temperature 40°C. Do not use detergent or soaps. Never put bin back without filter inside. You could damage the motor.

Replacing the filters

Slide the filter onto the inner shroud.

Slide the filter and inner shroud into the filter housing.

Removing and cleaning the brush bar

If the brush bar jams during use, the AirRAM will stop and the LEDs will appear red. Before checking for a blockage, remove the battery.

Rest the AirRAM on its side and locate the brush bar button on the right hand side. Press the button inwards and then pull the brush bar out from the bottom of the AirRAM.

The brush bar can now be removed, starting at the button end.

To remove hair from the brush bar, run an open pair of scissors down the groove to cut the hair, then pull it out.

Re-insert the brush bar, starting by the end furthest away from the button. Then line up and push the brush bar into the AirRAM until it clicks into place.

Replace the battery by sliding it down into the head assembly. It will click into place.

Clearing a jam / fault

If the brush bar jams during use, the AirRAM will stop and the LEDs will appear red. You will need to remove and clean the brush bar.

The AirRAM will not re-start until the red lights go out. This will take ten seconds.

If the problem persists, follow the troubleshooting instructions below.

DEVICE TECHNICAL SPECIFICATION

The symbol indicates that this product is covered by legislation for waste electrical and electronic products (EN2002/96/EC)
When the vacuum has reached the end of its life, it and the Li-Ion battery it contains should not be disposed of with general household waste. The battery should be removed from the vacuum and both should be disposed of properly at a recognised recycling facility.

Call your local council, via amenity site, or recycling centre for information on the disposal and recycling of electrical products.
Alternatively visit www.recycle-more.co.uk for advice on recycling and to find your nearest recycling facilities.

FOR HOUSEHOLD USE ONLY

Product Care

Your Gtech AirRAM doesn't need much maintenance: keep the filters clean, keep the brush bar tanglefree and charge the battery. Wipe it with a dry cloth if it gets dirty, including under the bin.

Troubleshooting

Product Support

If these initial tips don't solve your problem, we have various other ways to help.
Visit: www.gtech.co.uk/support

Grey Technology Limited
Brindley Road, Warndon, Worcester WR4 9FB
email: support@gtech.co.uk
telephone: 01905 345891
www.gtech.co.uk

Documents / Resources

References

• Everything you need to know to Recycle More
• Support and Customer Service | Gtech
• Gtech UK Official: Vacuum Cleaners, Home & Gardening

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Gtech AirRAM MK2 (AR29) - Cordless Vacuum Manual