Sealey PCB32 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions
and maintained properly, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT
CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL
INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Wear eye
Refer to instruction
protection
manual
1. SAFETY
 Ensure the conduit bender is in sound condition and good working order. Take action for immediate repair or replacement of damaged
parts. Use recommended parts only. The use of improper parts may be dangerous and will invalidate the warranty.
 Anchor the conduit bender to the floor or use assistance to prevent the conduit bender from lifting during use.
 Keep bender and associated parts clean for best and safest performance.
 Locate the conduit bender in a suitable, well lit work area.
 Keep work area clean and tidy and free from unrelated materials.
 Use on level and solid ground, preferably concrete.
 Ensure all non-essential persons keep a safe distance whilst the conduit bender is in use.
 Maintain correct balance and footing. Ensure the floor is not slippery and wear non slip shoes.
 Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain and/or tie back long hair.
 Wear appropriate safety clothing including gloves and eye protection.
 Keep hands away from moving parts when bending conduit.
s Caution! Cut conduit edges may be sharp, take care when handling any cut steelwork.
 DO NOT operate the conduit bender if damaged.
 DO NOT allow untrained persons to operate the conduit bender.
 DO NOT operate the conduit bender when you are tired, under the influence of alcohol, drugs or intoxicating medication.
 DO NOT use the conduit bender for purposes other than that for which it is intended.
 Store conduit bender in a safe, dry, childproof location.
2. INTRODUCTION
Professional folding A-frame conduit bender with vice. Suitable for galvanized and black enamel conduit. Supplied with two machine cast formers -
20 and 25mm, which will bend conduit up to a maximum length of 1100mm. The vice aids cutting lengths and threading. Additional former for
Ø32mm conduit: PCB32.03.
3. SPECIFICATION
Model No: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PCB25
Maximum Pipe Ø:. . . . . . . . . . . . . . . . . . . . . . . . . . . . 25mm(32mm with optional former*)
Die Sizes: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20, 25mm
Extended (W x D x H): . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 510 x 1030 x 1115mm
Folded (W x D x H): . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .510 x 145 x 1210mm
*Additional former for Ø32mm conduit: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PCB32.03
© Jack Sealey Limited
INSTRUCTIONS FOR:
PROFESSIONAL CONDUIT BENDER
MODEL NO:
Wear protective
gloves
Original Language Version
PCB25
PCB25 Issue:1 - 31/10/17