Sealey PCB32 Instruction Manual

thank you for purchasing a sealey product. manufactured to a high standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
 ensure the conduit bender is in sound condition and good working order.
take action for immediate repair or replacement of damaged parts. Use
recommended parts only. The use of improper parts may be dangerous
and will invalidate the warranty.
 Keep bender and associated parts clean for best and safest performance.
 locate the conduit bender in a suitable, well lit work area.
 Keep work area clean and tidy and free from unrelated materials.
 use on level and solid ground, preferably concrete.
 ensure all non-essential persons keep a safe distance whilst the conduit
bender is in use.
 maintain correct balance and footing. ensure the floor is not slippery
and wear non slip shoes.
 remove ill fitting clothing. remove ties, watches, rings and other loose
jewellery and contain and/or tie back long hair.
 Wear appropriate safety clothing including gloves and eye protection.
 Keep hands away from moving parts when bending conduit.
s Caution! cut conduit edges may be sharp, take care when handling any cut
steelwork.
 DO NOT operate the conduit bender if damaged.
 DO NOT allow untrained persons to operate the conduit bender.
 DO NOT operate the conduit bender when you are tired, under the
influence of alcohol, drugs or intoxicating medication.
 DO NOT use the conduit bender for purposes other than that for which
it is intended.
 store conduit bender in a safe, dry, childproof location.
 anchor the conduit bender to the floor or use assistance to prevent
the conduit bender from lifting during use.
2. INTRODUCTION & SPECIFICATION
Professional folding a-frame conduit bender with vice. suitable for galvanised
and black enamel conduit. supplied with three machine cast formers 20, 25
and 32mm which will bend conduit in accordance with Bs4568 up to a
maximum length of 1100mm. the vice aids cutting lengths and threading.
MODEL: .................................................................................................. PCb32
extended (WxdxH): ..............................................................530x1180x1065mm
folded (WxdxH): ................................................................... 530x380x1200mm
former sizes: .............................................................................................20mm
...................................................................................................................25mm
...................................................................................................................32mm
1................................ leg retaining pin.
2................ Bending lever retaining pin.
3...........................................centre pin.
4..............................................stop bar.
5.......................................... stop piece.
fig.1
6.................................................... Vice.
7..................................... Bending lever.
8............................................ roller pin.
9................................................former.
10...................Bending lever extension.
InstructIon manual for:
PROFESSIONAL CONDUIT bENDER
PCb32
model no:
3. ASSEMbLY
WARNING! Ensure that you have read and understood Section 1

Safety Instructions before operating the conduit bender.
WARNING! When the conduit bender is packed in its box it is

heavy and may require 2 people to move it.
3.1 remove the conduit bender from the box and check all parts are
present. refer to fig.1.
3.2 remove the leg retaining pin (1) and open the conduit bender to its
fullest extent. re-insert the leg retaining pin (1) to lock the leg into
position.
3.3 the vice (6) is secured beneath the platform for transit purposes.
remove the 3 retaining bolts and remove the vice (6). Place it on
top of the platform and bolt into position.
3.4 remove the bending lever retaining pin (2). fit the grooved roller and
pin (8) in the appropriate position on the bending lever (7) (fig.2).
secure the roller pin (8) in place with the r-clip.
3.5 select the size of former (9) required (fig.2) according to the diameter
of conduit to be bent. Withdraw the centre pin (3), insert the former
(9) and replace the centre pin (3).
3.6 raise the bending lever (7) to the upright position and lock in place
with the retaining pin (2). attach the bending lever extension (10).
3.7 swing the stop bar (4) to the upright position and insert the stop piece
(5) into the appropriate hole required and secure with the r-clip. the
conduit bender is now ready for use.
fig.2
fig.3
PcB32 Issue no:1 18/07/11