Sealey AP0615 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
1.1 GENERAL SAFETY
WARNING! Ensure Health & Safety, local authority, and
!
general workshop practice regulations are adhered to when
using this bench.
Locate bench in a suitable working area.
"
Keep the work area clean, uncluttered and ensure there is
"
adequate lighting.
WARNING! Use bench on level and solid ground, preferably
!
concrete. Avoid tarmacadam since the bench may sink into the
surface.
Keep the bench clean and tidy in accordance with good
"
workshop practice.
Keep children and unauthorised persons away from the
"
working area.
DO NOT use the bench for any purpose other than that for
#
which it is designed.
DO NOT do work on the bench without the workpiece being
#
adequately secured. Use clamps or a vice (not included but
available from your Sealey dealer) to secure the workpiece.
DO NOT use the bench out of doors.
#
DO NOT get the bench wet or use in damp or wet locations or
#
areas where there is condensation.
DO NOT clean the bench with any solvents which may
#
damage the paint surface.
2. INTRODUCTION & SPECIFICATION
35mm Thick wood composite top, with beech-effect laminate, and
epoxy coated steel frame. Available in two sizes.
Model No: AP0615 Size (H x W x L): 880 x 610 x 1500mm
Model No: AP0620 Size (H x W x L): 880 x 610 x 2000mm
3. CONTENTS
3.1 Do not attempt to move the unassembled bench in its box on
your own. Two people will be required to carry the box to the
assembly area.
3.2 Remove all parts and fixings from the box. Ensure that you
have adequate help to remove the bench top from the box ( It
is too heavy for one person to lift safely.)
3.4 Check the contents against the parts listed below. Should
there be any damaged or missing parts contact your supplier
immediately.
ITEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .QUANTITY
Wood Composite Worktop . . . . . . . . . . . . . . . . . . . . . . . .(1)
Support Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .(1)
Legs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .(4)
Leg Crosspieces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .(2)
Leg Tie Piece . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .(1)
Leg Braces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .(2)
M14 x 25mm Bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . .(18)
M14 Nuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .(18)
Washers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .(18)
Hex Head Wood Screws M11x36mm . . . . . . . . . . . . . . . .(6)
NOTE:
It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our catalogue and latest promotions call us on 01284 757525 and leave your full name, address and postcode.
Sole UK Distributor
Sealey Group,
Bury St. Edmunds, Suffolk.
INSTRUCTIONS FOR:
WITH WOOD COMPOSITE TOP
AP0615, AP0620
MODELS:
4. ASSEMBLY
4.1 Place a protective layer onto the floor e.g. the cardboard packing
from this product. Lay the worktop face down onto the protective
layer. Lay the support frame onto the top and align the six holes
in the frame with the six pre-drilled holes in the worktop (see
Fig.1). Fasten the frame to the top using the 6 M11 x 36mm hex
headed woodscrews provided.
4.2 Make up two end frames ensuring that the leg crosspiece that joins
the two legs together is the right way round as shown in Fig.2.
01284 757500
01284 703534
STEEL WORKBENCH
Fig. 1
Fig.2
www.sealey.co.uk
Web
sales@sealey.co.uk
email
AP0615, AP0620 - 1 - 230207