Advertisement
Smart Modular Revolving Door Installation Guide (21501043-003, 21501044-001)
07
（可选）安装门禁机
(Optional) Installing a Access Control Device
步骤1：拆除安装位挡片。
步骤2：将过线孔位于下端的挡片固定在PAD安装件上。
步骤3：拆下门禁机固定螺钉（请妥善保存），取下底板。
步骤4：将底板固定在挡片上
步骤5：将门禁机线缆穿过挡片过线孔。
步骤6：将门禁机固定在底板上。
Step 1: Remove the baffle plate from the installation position.
Step 2: Secure the baffle plate with a cable hole on the lower part to the pad mounting kit.
Step 3: Remove the screws (set aside) of the access control device and take off the baseplate.
Step 4: Secure the baseplate to the baffle plate.
Step 5: Route the cable of the access control device with through the cable hole in the baffle plate.
Step 6: Secure the access control device to the baseplate.
08
（可选）安装通道双门电磁锁
(Optional) Installing a Double-Door Magnetic Lock for an Aisle
吸铁组件
7
M4 x10
7
1.2 N·m
步骤8：将吸铁组件插入到旋转门门板的安装座上，并使用自带螺钉及白色橡胶垫片
步骤5：将电磁锁固定板固定到门框顶部。
将电磁吸铁固定在门板上。
步骤6：使用自带六角扳手将电磁锁主体
安装到固定板上。
注意
步骤7：安装电磁锁后盖板。
将电磁吸铁装到门板上时，请勿将螺钉拧太紧，让白色橡胶垫片保持适当弹
Step 5: Secure the magnetic lock fixing
性，白色橡胶垫片在自身的弹性作用下会将电磁吸铁自动调节到合适位置。
plate to the top of the door frame.
Step 8: Insert the magnet into the mounting base of the revolving door panel,
Step 6: Install the magnetic lock body
and secure the magnet to the door panel using the delivered screws and
onto the fixing plate using the
white rubber washers.
delivered hex key.
Step 7: Install the rear mounting plate
of the magnetic lock.
When securing the magnet to the door panel, do not over-tighten the
screws so that the white rubber washer is elastic. The washer will adjust
the magnet to an appropriate position because of its elasticity.
智能微模块 旋转门 安装指南(21501043-003, 21501044-001)
08
2
1
电磁锁盖板母板
Magnetic lock cover
mounting plate
4
5
3
7
6
8
白色橡胶片
White rubber washer
8
Magnet
（通道内）
(Inside the aisle)
（可选）安装通道双门电磁锁
(Optional) Installing a Double-Door Magnetic Lock for an Aisle
电磁锁盖板
Magnetic lock cover
2
1
NOTE
Before installing the magnetic lock body,
安装电磁锁主体前需将电磁锁线缆
route the magnetic lock cable into the
穿入顶框安装件中。
upper frame mounting kit.
步骤1：拆除门上安装件后部盖板的紧固螺钉。
Step 1: Remove the screws from the rear cover
步骤2：拆除电磁锁盖板母板，并将拆掉的4颗
螺钉保留备用。
Step 2: Remove the mounting plate of the
步骤3：拆除电磁锁盖板。
Step 3: Remove the magnetic lock cover.
09
（可选）调节通道双门电磁锁
(Optional) Adjusting a Double-Door Magnetic Lock for an Aisle
1
步骤1：调节电磁吸铁，直至电磁吸铁与门板完全平行并贴合，如图中
注意
如果上电后，发现电磁吸铁不能正常吸合，请按照以下方法检查：
用可以被磁化的铁质零件去吸电磁吸铁，检查是否正常提供磁力。
检查电磁锁是否与电磁吸铁恰好面对面对齐。
检查电磁锁与电磁吸铁之间是否有间隙。
出现以上三种情况之一，均会导致双门电磁锁与电磁吸铁无法正常吸合，
请按照以下的方法调节电磁吸铁：
检查电路，解决电路问题。
1
电磁吸铁与电磁锁存在间隙，请按如图中的
所示方法调节。
2
电磁吸铁两端高低不平，请使用如图中的
所示方法调节。
调节电磁吸铁固定座和门板，保证双门电磁锁与电磁吸铁完全贴合，
3 4
保证偏差尽可能小，请按如图中的
所示方法调节。
4
3
步骤4：拆除电磁锁固定板，拆除的螺丝保留备用。
Step 4: Remove the magnetic lock fixing plate and save the
of the mounting kit on the door.
magnetic lock cover, and save the
removed four screws for later use.
4
5
2
3
Step 1: Adjust the magnet until it is completely parallel to the door panel and in close contact with the door panel,
5
所示。
as shown by (5) in the figure.
If the magnet does not work properly after power-on, check the following items:
Check that the magnet provides magnetic force by attaching magnetizable iron parts to it.
Check that the magnetic lock is aligned with the magnet face-to-face.
Check that no gap exists between the magnetic lock and the magnet.
If any of the preceding conditions is not met, the double-door magnetic lock fails to attract the magnet.
Troubleshoot the magnet as follows:
Check the circuit and rectify any circuit fault.
If a gap exists between the magnetic lock and the magnet, rectify the fault as shown by (1) in the figure.
If the magnet is not level, adjust it as shown by (2) in the figure.
Adjust the magnet base and door panel to ensure that the double-door magnetic lock is completely attached
to the magnet and that the deviation is minimum. Adjust them as shown by (3) and (4) in the figure.
01
4
M4
5
5
1.2 N·m
6
6
安装电磁锁主体前需将电磁锁线缆穿入顶框安装件中。
removed screws for future use.
NOTE
Before installing the magnetic lock body, route the
magnetic lock cable into the upper frame mounting kit.
版权所有 © 华为技术有限公司2019。保留一切权利。
Copyright © Huawei Technologies Co., Ltd. 2019. All rights reserved.
Advertisement
