Page 1 SmartAX MA5616 Multi-service Access Module V800R308C01 Configuration Guide Issue Date 2011-10-30 HUAWEI TECHNOLOGIES CO., LTD.
Page 2 All other trademarks and trade names mentioned in this document are the property of their respective holders. Notice The purchased products, services and features are stipulated by the contract made between Huawei and the customer. All or part of the products, services and features described in this document may not be within the purchase scope or the usage scope.
Page 3: About This Document
SmartAX MA5616 Multi-service Access Module Configuration Guide About This Document About This Document Intended Audience This document describes the configuration of important services supported by the MA5616. The description covers the following topics: Purpose Networking Data plan Prerequisite(s) Note Configuration flowchart...
Page 4 SmartAX MA5616 Multi-service Access Module Configuration Guide About This Document Symbol Description Indicates a tip that may help you solve a problem or save your time. Provides additional information to emphasize or supplement important points of the main text. Command Conventions...
Page 5 SmartAX MA5616 Multi-service Access Module Configuration Guide About This Document 3.3.1 Configuring an Uplink Ethernet Port 3.15.1.2 Configuring the Monitoring Through the ESCM 3.15.2.1 Configuring the Monitoring Through the EPS30-4815AF 3.15.3 Configuring the Monitoring Through the Fan Updates in Issue 03 (2011-03-31)
Page 6: Table Of Contents
SmartAX MA5616 Multi-service Access Module Configuration Guide Contents Contents About This Document........................ii 1 Deploying Network Devices.......................1 1.1 Introduction to the Network Device Deployment....................2 1.2 Example of Deploying Network Devices......................3 2 Checking Before the Configuration...................7 2.1 Checking the Software Version..........................8 2.2 Checking the Board Status..........................8 3 Basic Configuration........................10...
Page 7 SmartAX MA5616 Multi-service Access Module Configuration Guide Contents 3.8.1.1 Configuring the Adaptive Clock Reference Source...............67 3.8.1.2 Configuring the Line Clock Reference Source................68 3.8.2 Configuring the Priority of the System Clock..................68 3.9 Configuring the System Time...........................69 3.9.1 Configuring the NTP Time........................69 3.9.1.1 (Optional) Configuring NTP Authentication..................70...
Page 8 SmartAX MA5616 Multi-service Access Module Configuration Guide Contents 3.14.3.2 Adding a Priority Tag to the Traffic Matching an ACL Rule............128 3.14.3.3 Enabling the Statistics Collection of the Traffic Matching an ACL Rule........129 3.14.3.4 Enabling the Mirroring of the Traffic Matching an ACL Rule..........130 3.15 Configuring Environment Monitoring......................130...
Page 9 SmartAX MA5616 Multi-service Access Module Configuration Guide Contents 7.1.1.6 (Optional) Configuring the Ringing Mode of an MG Interface...........227 7.1.1.7 (Optional) Configuring the TID Format of an MG Interface............229 7.1.1.8 Enabling an MG Interface......................231 7.1.2 Configuring the VoIP PSTN User......................232 7.1.2.1 Configuring the PSTN User Data....................232 7.1.2.2 (Optional) Configuring the System Parameters................235...
Page 10 SmartAX MA5616 Multi-service Access Module Configuration Guide Contents 7.4 Configuring the FoIP Service (Based on the H.248 Protocol)...............297 7.5 Configuring the FoIP Service (Based on the SIP Protocol)................299 7.6 Configuring the MoIP Service (Based on the H.248 Protocol)..............302 7.7 Configuring the MoIP Service (Based on the SIP Protocol)................304 7.8 Configuring the Security and Reliability of the Voice Service..............306...
Page 11 SmartAX MA5616 Multi-service Access Module Configuration Guide Contents 9.2 Configuration Example of the Multicast Service (Multicast VLAN Mode)..........426 9.2.1 Configuration Example of the Multicast Video Service (Static Configuration Mode)......426 9.2.2 Configuration Example of the Multicast Video Service (Dynamic Generation Mode)......430 9.3 Configuration Example of the VoIP Service....................434...
Page 12: Deploying Network Devices
SmartAX MA5616 Multi-service Access Module Configuration Guide 1 Deploying Network Devices Deploying Network Devices About This Chapter Deploy the ONUs at sites according to network planning so that the NMS, OLT, and ONU can communicate with each other. 1.1 Introduction to the Network Device Deployment...
Page 13: Introduction To The Network Device Deployment
SmartAX MA5616 Multi-service Access Module Configuration Guide 1 Deploying Network Devices 1.1 Introduction to the Network Device Deployment This topic describes how to deploy network devices, including optical network unit (ONU) data plan, ONU offline deployment (through the NMS or the CLI of the OLT), ONU installation, and ONU binding.
Page 14: Example Of Deploying Network Devices
SmartAX MA5616 Multi-service Access Module Configuration Guide 1 Deploying Network Devices Table 1-2 Activities involved in network device deployment in the scenario without the NMS Activities Description ONU data plan Perform the data plan for the OLT and ONU according to the actual FTTx service plan and the corresponding OLT version.
Page 15 SmartAX MA5616 Multi-service Access Module Configuration Guide 1 Deploying Network Devices Figure 1-1 Example network of device deployment in the scenario with the NMS NMS client_A NMS client_B Router Splitter Splitter ONU_A ONU_B ONU_C ONU_D The procedure for deploying network devices in the scenario with the NMS is as follows: According to the user's FTTx data plan, the commissioning engineer prepares the network planning sheet and obtains the resource deployment sheet.
Page 16 SmartAX MA5616 Multi-service Access Module Configuration Guide 1 Deploying Network Devices l If the Auth LED is always on, it indicates that the ONU registers successfully. After confirming that the ONU works in the normal state (the Link LED is on and the Auth LED blinks), the hardware installation engineer records the ONU SN and reports the SN to the commissioning engineer.
Page 17 SmartAX MA5616 Multi-service Access Module Configuration Guide 1 Deploying Network Devices The procedure for deploying network devices in the scenario without the NMS is as follows: According to the user's FTTx service plan and the corresponding OLT version, the commissioning engineer performs the data plan for the OLT and ONU.
Page 18: Checking Before The Configuration
SmartAX MA5616 Multi-service Access Module Configuration Guide 2 Checking Before the Configuration Checking Before the Configuration About This Chapter Before the service configuration, you need to check the software version and board status of the MA5616 to ensure that the service runs normally after the configuration.
Page 19: Checking The Software Version
The versions of the host software and patch meet the deployment requirement. If the versions do not meet the deployment requirement, contact Huawei technical support center to upgrade the host software if necessary. For details about the upgrade, see the MA5616 Upgrade guide.
Page 20 SmartAX MA5616 Multi-service Access Module Configuration Guide 2 Checking Before the Configuration – If all the required boards are inserted correctly and all the boards are in the normal state, the operation ends. – If a required board is not inserted in the device, insert the board and run the board confirm command to confirm the board in the auto-find state.
Page 21: Basic Configuration
This topic describes three modes of managing the MA5616 from the maintenance terminal. 3.2 Configuring the U2000 The MA5616 can be interconnected with Huawei iManager U2000 (hereinafter referred to as U2000). Hence, the administrator can maintain and manage the device through the U2000. The MA5616 can be interconnected with the U2000 in inband or outband networking mode.
Page 22 SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration Configuring the xDSL profile is a prerequisite for configuring an xDSL access service. This topic describes how to configure an ADSL2+ profile, an SHDSL profile, and a VDSL2 profile. 3.8 Configuring the System Clock This topic describes how to configure the system clock to restrict the clock frequency and phase of each node on a network within the preset tolerance scope.
Page 23: Configuring The Maintenance Terminal
SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration 3.1 Configuring the Maintenance Terminal This topic describes three modes of managing the MA5616 from the maintenance terminal. 3.1.1 Configuring Management Through a Local Serial Port This topic describes how to connect the maintenance terminal to the MA5616 through a local serial port, log in to the MA5616, and then manage the MA5616 from the maintenance terminal.
Page 24 SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration Figure 3-2 Flowchart for configuring management through a local serial port Start Connect the serial port cable Start the HyperTerminal Set parameters of the HyperTerminal Set the terminal emulation type...
Page 25 SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration Figure 3-3 Setting up a connection Set the serial port. On the PC that is connected to the MA5616, select the number of the standard character terminal or PC terminal serial port. You can select "COM1" or "COM2". In this example, "COM2"...
Page 26 SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration l Baud rate: 9600 bit/s l Data bit: 8 l Parity: None l Stop bit: 1 l Flow control: None NOTE l The baud rate of the HyperTerminal must be the same as that of the serial port on the MA5616. By default, the baud rate of the serial port on the MA5616 is 9600 bit/s.
Page 27 SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration Figure 3-6 HyperTerminal interface Step 4 Set the terminal emulation type. Choose File > Properties on the HyperTerminal interface. In the dialog box that is displayed, click the Settings tab, and set the terminal emulation type to VT100 or Auto detect. Use default values for other parameters.
Page 28 SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration Figure 3-7 Setting the terminal emulation type Step 5 Set the line delay and the character delay. Click ASCII Setup. In the dialog box that is displayed, set Line delay to 200 ms and Character delay to 200 ms, and use default values for other parameters.
Page 29: Configuring Outband Management
SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration Figure 3-8 Setting the line delay and the character delay ----End Result On the HyperTerminal interface, press Enter, and the system prompts you to enter the user name. Enter the user name and the password for user registration (by default, the super user name is root and the password is mduadmin), and wait until the CLI prompt character is displayed.
Page 30 SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration Figure 3-9 Example network for configuring outband management over a LAN in the telnet mode MA5616 In this example network, the IP address of the maintenance Ethernet port of the MA5616 and the IP address of the maintenance terminal are in the same network segment.
Page 31 SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration Figure 3-10 Example network for configuring outband management over a WAN in the telnet mode Router MA5616 In this example network, the MA5616 is connected to the WAN through the maintenance Ethernet port.
Page 32 SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration Figure 3-11 Flowchart for outband management in the telnet mode Start Set up the configuration environment Configure the IP address and subnet mask of the maintenance port Is it a WAN environment?
Page 33: Configuring Inband Management (Gpon Upstream)
>>User name:root >>User password: Huawei Integrated Access Software (MA5616). Copyright(C) Huawei Technologies Co., Ltd. 2002-2010. All rights reserved. ----End Result After logging in to the MA5616, you can manage the MA5616. For instructions on CLI, see CLI Operation Characteristics.
Page 34 SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration Networking - LAN Figure 3-13 Example network for configuring inband management over a LAN in the GPON upstream mode MA5616 Networking - WAN Figure 3-14 Example network for configuring inband management over a WAN in the GPON...
Page 35: Configuring Inband Management (Ge Upstream)
SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration Figure 3-15 Flowchart for configuring inband management in the GPON upstream mode Start Set up the configuration environment Configure the L3 interface of the OLT Configure corresponding profiles Adding an ONU...
Page 36 SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration Prerequisites You must be logged in to the system through a local serial port. For the configuration process, see 3.1.1 Configuring Management Through a Local Serial Port. The IP address of the maintenance terminal must be properly configured.
Page 37 SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration Networking - WAN Figure 3-17 shows an example network for configuring inband management over a WAN in the telnet mode. Figure 3-17 Example network for configuring inband management over a WAN in the telnet...
Page 38 SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration Figure 3-18 Flowchart for configuring inband management in the telnet mode Start Set up the configuration environment Configure the IP address of the VLAN L3 interface Is it a WAN...
Page 39 >>User name:root >>User password: Huawei Integrated Access Software (MA5616). Copyright(C) Huawei Technologies Co., Ltd. 2002-2010. All rights reserved. ----End Result After logging in to the MA5616, you can manage the MA5616. For instructions on CLI, see CLI Operation Characteristics.
Page 40: Configuring The U2000
3 Basic Configuration 3.2 Configuring the U2000 The MA5616 can be interconnected with Huawei iManager U2000 (hereinafter referred to as U2000). Hence, the administrator can maintain and manage the device through the U2000. The MA5616 can be interconnected with the U2000 in inband or outband networking mode. The following part describes how to configure the inband networking and outband networking based on SNMP V1, SNMP V2c, and SNMP V3 respectively.
Page 41 SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration Networking - Outband Networking Mode As shown in Figure 3-21, the SNMP protocol is transmitted through the management channel. Service packets and management packets are transmitted through different channels. The outband NMS management is implemented through the maintenance network port.
Page 42 SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration Figure 3-22 Flowchart for configuring the NMS Flowchart for configuring the MXU Start Set the SNMP parameters Enable trap sending Set the IP address of the target host for traps...
Page 43 Run the snmp-agent target-host command to configure the IP address of the target host of the traps. The host name is huawei, the IP address of the host is 10.10.1.10/24 (that is, the IP address of the U2000), the name of the target host is ABC, the SNMP version is V1, and the security name is private (that is, the SNMP community name).
Page 44 SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration Run the route print command to query the information about the current routing table. NOTE If the IP address of the outband NMS port and the IP address of the U2000 are in the same network segment, you need not configure the route.
Page 45: Configuring The U2000 (Based On Snmpv2C)
HW-075528780808 snmp-agent sys-info location Shenzhen_China snmp-agent sys-info version v1 snmp-agent trap enable standard snmp-agent target-host trap-hostname huawei address 10.10.1.10 trap-paramsname ABC snmp-agent target-host trap-paramsname ABC v1 securityname private snmp-agent trap source meth 0 save The following part provides the script for configuring the inband NMS (on the device). The management VLAN ID of the upstream port is 30.
Page 46 SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration If the device is interconnected with the NMS through the GE upstream port in inband networking mode, the communication port (GE upstream port) must be configured. For detailed procedure, see 3.1.4 Configuring Inband Management (GE...
Page 47 Run the command to configure the IP address of the target host of the traps. The host name is huawei, the IP address of the host is 10.10.1.10/24 (that is, the IP address of the U2000), the name of the target host is ABC, the SNMP version is V2c, and the security name is private (that is, the SNMP community name).
Page 48 SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration Run the route add 10.50.1.0 mask 255.255.255.0 10.10.1.1 command to add a route. Run the route print command to query the information about the current routing table. NOTE If the IP address of the outband NMS port and the IP address of the U2000 are in the same network segment, you need not configure the route.
Page 49: Configuring The U2000 (Based On Snmpv3)
HW-075528780808 snmp-agent sys-info location Shenzhen_China snmp-agent sys-info version v2c snmp-agent trap enable standard snmp-agent target-host trap-hostname huawei address 10.10.1.10 trap-paramsname ABC snmp-agent target-host trap-paramsname ABC v2c securityname private snmp-agent trap source meth 0 save The following part provides the script for configuring the inband NMS (on the device). The management VLAN ID of the upstream port is 30.
Page 50 Internet subtree. huawei(config)#snmp-agent usm-user v3 user1 group1 authentication- mode md5 authkey123 privacy-mode des56 prikey123 huawei(config)#snmp-agent group v3 group1 privacy read-view hardy write-view hardy huawei(config)#snmp-agent mib-view hardy include internet (Optional) Set the information about the administrator and the device.
Page 51 Run the snmp-agent target-host command to configure the IP address of the target host of the traps. The host name is huawei, the IP address of the host is 10.10.1.10/24 (that is, the IP address of the U2000), the name of the target host is ABC, the SNMP version is V3, the security name is user1 (when SNMP V3 is used, the security name is the USM user name), and the traps are authenticated and encrypted.
Page 52 SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration Configure the IP address of the gateway from the NMS server to network segment 10.50.1.0/24 to 10.10.1.1. – In the Solaris operating system (OS), do as follows: Run the route add 10.50.1.0 10.10.1.1 command to add a route.
Page 53 The IP address is the management IP address of the MA5616. l Select the SNMP parameters based on the selected SNMP version. This section considers the SNMP V3: huawei profile as an example. You can select the profile according to the plan.
Page 54: Configuring The Attributes Of The Upstream Port
Shenzhen_China snmp-agent local-engineid 0123456789 snmp-agent sys-info version v3 snmp-agent trap enable standard snmp-agent target-host trap-hostname huawei address 10.10.1.10 trap-paramsname ABC snmp-agent target-host trap-paramsname ABC v3 securityname user1 privacy snmp-agent trap source meth 0 save The following part provides the script for configuring the inband NMS (on the device). The management VLAN ID of the upstream port is 30.
Page 55 SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration Table 3-5 Configuration principles of uplink and cascaded ports on an MA5616 Control Board Daughter Board Configuration Principles on the Control Board CCUB GP1A l GE port 0: is set as a cascaded or uplink port.
Page 56 SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration – After the auto-negotiation mode is enabled, the port automatically negotiates with the peer port for the rate and working mode of the Ethernet port. – After the auto-negotiation mode is disabled, the rate and working mode of the port are in the forced mode (adopt default values or are set through command lines).
Page 57: Configuring The Attributes Of The Upstream Pon Port
SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration Run the flow-control command to enable the flow control on the Ethernet port. Run the mirror port command to mirror the Ethernet port. ----End Example Assume that: The port rate is 1000 Mbit/s.
Page 58: Configuring The System Energy-Saving Function
SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration Example To set the password for registering with the OLT through the GPON port, set the lower limit for the receive optical power of the optical transceiver to 5 dBm and the upper limit for the receive...
Page 59: Configuring The Link Aggregation Of Upstream Ethernet Port
SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration – Run the undo broad-service power-off shutdown command to enable disabled bandwidth services. ----End Example To manually power off an ASRB board that is not used and in slot 0/4 of an MA5616 to reduce...
Page 60: Configuring The Ancp
SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration Run the display link-aggregation all command to query the type, number and working mode of the aggregated Ethernet ports. ----End Result In ETH mode, the PC can still access the Internet through PPPoE dialup after you run the shutdown command to deactivate port 0/0/0 or 0/0/1.
Page 61 SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration Procedure Step 1 Run the ancp session command to enter the ANCP session mode. NOTE Currently, the system supports only two ANCP sessions. Step 2 Run the ancp ip command to configure the GSMP communication IP address for the ANCP session.
Page 62 SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration NOTE Before an ANCP session is enabled, related parameters can be modified. After an ANCP session is enabled, related parameters cannot be modified. Step 9 Run the quit command to quit the ANCP mode.
Page 63: Configuring A Vlan
SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration Session down send trap status : Disable Session up send trap status : Disable 3.6 Configuring a VLAN Configuring VLAN is a prerequisite for configuring a service. Hence, before configuring a service, make sure that the VLAN configuration based on planning is complete.
Page 64 SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration Table 3-8 Default parameter settings of VLAN Parameter Default Setting Remarks Default VLAN of VLAN ID: 1 the system Type: smart VLAN Reserved VLAN VLAN ID range: You can run the vlan reserve command to...
Page 65 SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration VLAN Configuration VLAN Description Application Scenario Type Command To add a MUX VLAN, One MUX VLAN may MUX VLANs are VLAN run the vlan vlanid contain multiple applicable to FE or mux command.
Page 66 SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration Configuration VLAN Type VLAN Application Command Description Scenario Attri bute QinQ To configure QinQ The VLAN with The packets from a Applicable to the as the attribute of a this attribute can...
Page 67 SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration Configuration VLAN Type VLAN Application Command Description Scenario Attri bute To configure The VLAN with The packets from a Applicable to the stacking as the this attribute can stacking VLAN...
Page 68: Configuring The Xdsl Profile
SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration NOTE l To configure attributes for the VLANs with consecutive IDs in batches, run the vlan attrib vlanid to end- vlanid command. l To configure attributes for the VLANs with inconsecutive IDs in batches, run the vlan attrib vlan-list command.
Page 69 SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration Prerequisites Run the switch adsl mode to rfc4706 command to switch to the ADSL mode NGADSL. Context The MA5616 supports two ADSL modes, that is, ADSL mode and NGADSL mode. The two modes can be switched by running a command.
Page 70 SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration – snr: Indicates the SNR margin, which refers to the idle space for carrying noise, excluding the space for carrying signals. In general, the SNR margin of the minimum tone is considered as the SNR margin of the entire ADSL connection.
Page 71: Configuring The Shdsl Profile
3 interleaved-delay 10 10 rate 1024 2048 3096 1024 2048 3096 huawei(config)#adsl line-template quickadd 3 line 3 channel1 3 60 70 channel2 3 3.7.2 Configuring the SHDSL Profile This topic describes how to configure the SHDSL line profile and alarm profile.
Page 72: Configuring The Vdsl2 Profile
To add SHDSL line profile 3 with the line rate of 4096 kbit/s, which is used to activate the 4- wire SHDSL port, do as follows: huawei(config)#shdsl line-profile quickadd 3 line four-wire rate 4096 Assume that the loop attenuation threshold is 10 dB, SNR margin is 0 dB, ES threshold is 100s, SES threshold is 100s, CRC abnormality duration threshold is 10000, LOSWS threshold is 100s, UAS threshold is 100s.
Page 73 SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration Context A VDSL2 line template consists of a VDSL2 line profile and a VDSL2 channel profile. Before activating a VDSL2 port, bind a VDSL2 line template to the port. A VDSL2 alarm template consists of a VDSL2 line alarm profile and a VDSL2 channel alarm profile.
Page 74 SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration and therefore the setting of the path mode is not required in this case. To set the ATM mode as the VDSL2 path mode, select atm. To set the PTM mode as the VDSL2 path mode, select ptm.
Page 75: Configuring The Vdsl2 Profile (Ti Mode)
SNR margin: 6 dB Downstream minimum INP: 4 Upstream minimum INP: 2 huawei(config)#vdsl line-profile quickadd 3 snr 60 0 300 60 0 300 huawei(config)#vdsl channel-profile quickadd 3 interleaved-delay 8 2 inp 4 2 rate 128 10000 128 10000 2048 2048 huawei(config)#vdsl line-template quickadd 3 line 3 channel1 3 100 100 3.7.3.2 Configuring the VDSL2 Profile (TI Mode)
Page 76 SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration Procedure Configure a VDSL2 line profile. Run the vdsl service-profile quickadd command to quickly add a VDSL2 service profile, or run the vdsl service-profile add command to interactively add a VDSL2 service profile.
Page 77: Configuring The System Clock
3 bearer1-interleaved-delay 8 2 bearer1-inp 4 2 huawei(config)#vdsl noise-margin-profile quickadd 3 snr-margin 60 0 100 60 0 3.8 Configuring the System Clock This topic describes how to configure the system clock to restrict the clock frequency and phase of each node on a network within the preset tolerance scope.
Page 78: Configuring The Reference Source Of The System Clock
SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration On the traditional telecommunications network, the TDM service carried on the AN is mainly the voice service. Cumulative inconsistency between the clocks at both ends of the bearer network over a long time causes frame slip, which reduces the quality of the voice service.
Page 79: Configuring The Line Clock Reference Source
SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration Example To configure system clock resource 0 for receiving ACM clock packets from Layer 3 interface whose IP address is 20.20.20.20 (assume that the subnet mask length is 24), run the following...
Page 80: Configuring The System Time
SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration Prerequisites The system clock reference source must be configured. Context The added system clock source can be used in the system only after it is configured with a priority. The priority of the clock source takes effect immediately after it is configured. This operation, however, may cause the clock switching in the system.
Page 81: Optional) Configuring Ntp Authentication
SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration NTP is developed from the time protocol and the ICMP timestamp message protocol, with special design on the aspects of accuracy and robustness. NTP runs over UDP with port number as 123.
Page 82: Configuring The Ntp Broadcast Mode
SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration Prerequisites Before configuring the NTP authentication, make sure that the network interface and the routing protocol of the MA5616 are configured so that the server and the client are reachable to each other at the network layer.
Page 83 SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration Prerequisites Before configuring the NTP broadcast mode, make sure that the network interface and the routing protocol of the MA5616 are configured so that the server and the client are reachable to each other at the network layer.
Page 84: Configuring The Ntp Multicast Mode
SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration Run the ntp-service authentication-keyid command to set an NTP authentication key. Run the ntp-service reliable authentication-keyid command to declare that the key is reliable. Add a VLAN L3 interface. Run the vlan command to create a VLAN.
Page 85 SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration to 3 (client mode) and 4 (server mode) with the server to estimate the network delay between the client and the server. The client then enters the multicast client mode, continues to listen to...
Page 86: Configuring The Ntp Unicast Server Mode
SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration Run the ip address command to configure the IP address and subnet mask of the VLAN interface so that the IP packets in the VLAN can participate in the L3 forwarding.
Page 87 SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration Precaution In the client/server mode, you need to configure only the client, and need not configure the server. The clock stratum of the synchronizing device must be lower than or equal to that of the synchronized device.
Page 88: Configuring The Ntp Peer Mode
2 huawei(config-if-vlanif2)#ip address 10.10.10.10 24 huawei(config-if-vlanif2)#quit huawei(config)#ntp-service unicast-server 10.20.20.20 source-interface vlanif 2 huawei(config)#acl 3010 huawei(config-acl-adv-3010)#rule deny ip source any destination 10.10.10.10 0.0.0.0 huawei(config-acl-adv-3010)#rule permit ip source 10.20.20.20 0.0.0.0 destination 10.10.10.10 0.0.0.0 huawei(config-acl-adv-3010)#quit huawei(config)#packet-filter inbound ip-group 3010 port 0/0/0 3.9.1.5 Configuring the NTP Peer Mode...
Page 89 SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration Figure 3-29 NTP peer mode Precaution In the peer mode, you need to configure the NTP mode only on the active peer. The peers determine clock synchronization according to the clock stratum instead of according to whether the peer is an active peer.
Page 90: Configuring The User Security
SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration Example Assume the following configurations: One MA5616 functions as the NTP active peer (IP address of the L3 interface of VLAN 2: 10.10.10.10/24) and works on clock stratum 4, the other MA5616 (IP address: 10.10.10.20/24) functions as the NTP passive peer, the active peer sends...
Page 91: Configuring Anti-Theft And Roaming Of User Account Through Pitp
SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration Parameter Default Setting Remarks DHCP option82 Global function: disabled The DHCP option82 function can be enabled only when the functions VLAN-level function: enabled at all levels are enabled. Anti-IP Global function: disabled...
Page 92 SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration of PC1, the BRAS discovers that the user account does not match the physical port information and thus rejects the dialup access request of PC2. Default Configuration Table 3-14 lists the default settings related to PITP.
Page 93 SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration The PITP function can be enabled or disabled at two levels. The PITP function is enabled only when it is enabled at both levels. Global PITP function: Run the pitp enable pmode command to enable global PITP P mode.
Page 94: Configuring Anti-Theft And Roaming Of User Accounts Through Dhcp
CID format for the Ethernet access mode: shelf ID slot ID port ID:VLAN ID To enable the PITP P function for the traffic stream with VLAN ID 30, do as follows: huawei(config)#raio-mode user-defined pitp-pmode huawei(config)#raio-format pitp-pmode cid atm anid atm frame/slot/port:vpi.vci huawei(config)#raio-format pitp-pmode cid eth anid eth frame/slot/port:vlanid huawei(config)#raio-format pitp-pmode rid atm plabel...
Page 95 SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration Table 3-15 Default settings related to DHCP option82 Parameter Default Setting Status of the DHCP option82 function Global status: disabled VLAN-level status: enabled Status of the DHCP sub-option 7 Disabled...
Page 96: Configuring The Anti-Ip Address Attack
RID format for all access modes: label of the service port To enable the DHCP option82 function, do as follows: huawei(config)#raio-mode user-defined dhcp-option82 huawei(config)#raio-format dhcp-option82 cid eth anid eth frame/slot/subslot/ port:vlanid huawei(config)#raio-format dhcp-option82 cid atm anid frame/slot/port:vpi.vci huawei(config)#raio-format dhcp-option82 rid eth splabel...
Page 97: Configuring The Anti-Mac Address Attack
SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration After the configuration, only the users with specified IP addresses can access the network, preventing malicious users from forging the IP addresses of authorized users. The procedure for configuring anti-IP address spoofing is as follows: Anti-IP address spoofing can be enabled or disabled at two levels.
Page 98 SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration MA5616 does not support direct binding of a MAC address to a port. Instead, you need to configure static MAC address entries for the port and set its maximum number of learnable MAC addresses to 0.
Page 99: Configuring System Security
SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration The index of the service port is 1. The static MAC address of this service port is 1010-1010-1010. The maximum number of learnable MAC addresses of this service port is 0.
Page 100: Configuring Firewall
SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration 3.11.1 Configuring Firewall Configuring system firewall can control the packets that go through the management port of the device so that unauthorized operators cannot access the system through the inband or outband channel.
Page 101 To add the IP addresses in network segment 10.10.10.0 to the firewall blacklist and bind ACL 3000 to these IP addresses, do as follows: huawei(config)#acl 3000 huawei(config-acl-adv-3000)#rule deny ip source 10.10.10.0 0.0.0.255 destination 10.10.10.20 0 huawei(config-acl-adv-3000)#quit huawei(config)#firewall blacklist enable acl-number 3000...
Page 102: Preventing The Access Of Invalid Users
To deny the users in network segment 172.16.25.0 to access the maintenance Ethernet port with IP address 172.16.25.28 on the device, do as follows: huawei(config)#acl 3001 huawei(config-acl-adv-3001)#rule 5 deny icmp source 172.16.25.0 0.0.0.255 destin ation 172.16.25.28 0 huawei(config-acl-adv-3001)#quit huawei(config)#firewall enable...
Page 103: Preventing The Attack Of Invalid Users
SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration To bind static MAC address 1010-1010-1010 to service port 1, and set the maximum number of learnable MAC addresses to 0, that is, service port 1 permits only the packet whose source...
Page 104 SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration CAUTION To ensure device security, it is recommended that you enable this function. The anti-MAC spoofing function can be enabled or disabled at three levels. The anti-MAC spoofing function is enabled only when it is enabled at all the three levels.
Page 105: Configuring Aaa
SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration huawei(config-vlan-srvprof-2)#quit huawei(config)#vlan bind service-profile 10 profile-id 2 To enable anti-MAC spoofing for VLAN 10, and set the maximum number of MAC addresses that can be bound to service port 2 to 7, do as follows:...
Page 106: Configuring The Local Aaa
SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration Figure 3-30 Example network of the AAA application RADIUS server MA5616 MA5600T HWTACACS server The preceding figure shows that the AAA function can be implemented on the MA5616 in the following three ways: The MA5616 functions as a local AAA server.
Page 107 Step 2 Create a domain. NOTE l A domain is a group of users of the same type. l In the user name format userid@domain-name (for example, huawei20041028@huawei.net), "userid" indicates the user name for authentication and "domain-name" followed by "@" indicates the domain name.
Page 108: Configuring The Remote Aaa (Based On The Radius Protocol)
SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration Info: Create a new domain huawei(config-aaa-domain-isp)#authentication-scheme newscheme huawei(config-aaa-domain-isp)#quit huawei(config-aaa)#local-user user1 password a123456 3.12.2 Configuring the Remote AAA (Based on the RADIUS Protocol) The MA5616 is interconnected with the RADIUS server through the RADIUS protocol to implement authentication and accounting.
Page 109 By default, the shared key of the RADIUS server is huawei. (Optional) Run the radius-server timeout command to set the response timeout time of the RADIUS server.
Page 110 Step 4 Create a domain. A domain is a group of users of the same type. In the user name format userid@domain-name (for example, huawei20041028@huawei.net), "userid" indicates the user name for authentication and "domain-name" followed by "@" indicates the domain name.
Page 111: Configuring The Remote Aaa (Based On The Hwtacacs Protocol)
SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration Run the quit command to return to the AAA mode. ----End Example User1 in the isp domain adopts the RADIUS protocol for authentication and accounting. The accounting interval is 10 minutes, the authentication password is a123456, RADIUS server 129.7.66.66 functions as the primary authentication and accounting server, and RADIUS server...
Page 112 SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration obtains the prompt of entering the user name from the daemon. Then, the NAS displays the message to the user. When the remote user enters the user name, the NAS transmits the user name to the daemon.
Page 113 SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration Run the quit command to return to the AAA mode. Step 4 Configure the HWTACACS protocol. The configuration of the HWTACACS protocol of the MA5616 is on the basis of the HWTACACS server group.
Page 114 Step 5 Create a domain. A domain is a group of users of the same type. In the user name format userid@domain-name (for example, huawei20041028@huawei.net), "userid" indicates the user name for authentication and "domain-name" followed by "@" indicates the domain name.
Page 115: Configuration Example Of The Authentication Based On The Radius Protocol (Device Management Users)
SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration Example User1 in the isp domain adopts the HWTACACS protocol for authentication, authorization, and accounting. The accounting interval is 10 minutes, the authentication password is a123456, HWTACACS server 129.7.66.66 functions as the primary authentication, authorization, and accounting server, and HWTACACS server 129.7.66.67 functions as the standby authentication,...
Page 116 SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration The RADIUS server with the IP address 129.7.66.67 functions as the secondary server for authentication. The authentication port ID is 1812. Other parameters adopt the default settings. Networking Figure 3-31 shows the example network of RADIUS authentication.
Page 117 SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration Step 3 Create a domain named isp1. NOTE l A domain is a group of users of the same type. l When the user name is in the format of userid@domain-name (for example, huawei20041028@isp1.net), "domain-name"...
Page 118: Configuration Example Of The Authentication Based On The Hwtacacs Protocol (Device Management Users)
SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration Permitted Reenter Number(0--4):4 User's Appended Info(<=30 chars): aaa Adding user succeeds Repeat this operation? (y/n)[n]:n ----End Result When the RADIUS server is reachable, the management user can log in to the MA5616 through Telnet.
Page 119 SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration Service Requirements Prefer the HWTACACS server to authenticate management user of domain isp1. Local authentication can be used when the HWTACACS server is unreachable. The user logs in to the server carrying the domain name.
Page 120 SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration Create HWTACACS server template named test-login with HWTACACS server 129.7.66.66 as the primary authentication server, and HWTACACS server 129.7.66.67 as the secondary authentication server. huawei(config)#hwtacacs-server template test-login Create a new HWTACACS-server template huawei(config-hwtacacs-test-login)#hwtacacs-server authentication 129.7.66.66 1812...
Page 121: Configuring The Acl For Packet Filtering
SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration huawei(config)#terminal user name User Name(length<6,15>):user01 //Management user name: user01 User Password(length<6,15>): //Password: test01pwd Confirm Password(length<6,15>): User profile name(<=15 chars)[root]: User's Level: 1. Common User 2. Operator 3. Administrator:2 Permitted Reenter Number(0--4):4 User's Appended Info(<=30 chars): aaa...
Page 122 If the rules are issued to the port from different ACLs, the rule activated later has priority over the one activated earlier. Precaution Because the ACL is flexible in use, Huawei provides the following suggestions on its configuration: It is recommended that you define a general rule, such as permit any or deny any, in each ACL, so that each packet has a matching traffic rule that determines to forward or filter the unspecified packet.
Page 123: Configuring The Basic Acl For Packet Filtering
SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration Check whether ACL rules occupy too many resources. If ACL rules occupy too many resources, deactivate or delete the unimportant or temporarily unused ACL configurations, and then configure and enable the protocol module.
Page 124: Configuring The Advanced Acl For Packet Filtering
SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration huawei(config)#time-range time1 00:00 to 12:00 fri huawei(config)#acl 2000 huawei(config-acl-basic-2000)#rule permit source 2.2.2.2 0.0.0.0 time-range time1 huawei(config-acl-basic-2000)#rule deny time-range time1 huawei(config-acl-basic-2000)#quit huawei(config)#packet-filter inbound ip-group 2000 port 0/1/0 huawei(config)#save 3.13.2 Configuring the Advanced ACL for Packet Filtering...
Page 125: Configuring The Link Layer Acl For Packet Filtering
VLAN interface on the device, do as follows: huawei(config)#acl 3001 huawei(config-acl-adv-3001)rule 1 deny icmp destination 10.10.10.101 0 huawei(config-acl-adv-3001)rule 2 deny tcp destination 10.10.10.101 0 destination- port eq telnet huawei(config-acl-adv-3001)quit huawei(config)#packet-filter inbound ip-group 3001 rule 1 port 0/1/0...
Page 126: Configuring Qos
To create a link layer ACL rule that allows data packets with protocol type 0x8863 (pppoe- control message), VLAN ID 12, CoS 1, source MAC address 2222-2222-2222, and destination MAC address 00e0-fc11-4141 to pass, do as follows: huawei(config)#acl 4001 huawei(config-acl-link-4001)rule 1 permit type 0x8863 cos 1 source 12 2222-2222-2222 0000-0000-0000 destination 00e0-fc11-4141 0000-0000-0000 huawei(config-acl-basic-4001)quit huawei(config)#save 3.14 Configuring QoS...
Page 127: Configuring Traffic Management
SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration 3.14.1 Configuring Traffic Management This topic describes how to configure traffic management on the MA5616. Overview The MA5616 supports traffic management for the inbound and outbound traffic streams of the system.
Page 128 SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration Item Parameter Description Priority policies The priority policies are classified into the following three types: l user-cos: Copy the 802.1p priority in the outer VLAN tag of the packet to the 802.1p priority in the VLAN tag of the upstream packet.
Page 129 Assume that the CIR is 2048 kbit/s, 802.1p priority of the upstream packet is 6, and the scheduling policy of the downstream packet is Tag-In-Package. To add traffic profile 9 with these settings, do as follows: huawei(config)#traffic table ip index 9 cir 2048 priority 6 priority-policy tag-In- Package Create traffic descriptor record successfully...
Page 130: Configuring Rate Limitation On An Ethernet Port
SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration CTAG Mapping Priority: - CTAG Default Priority: 0 Priority Policy : tag-pri : 2048 kbps : 67536 bytes : 4096 kbps : 133072 bytes Color Mode : color-blind Referenced Status...
Page 131 SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration services can hold a burst of the total user bandwidth so that the total user bandwidth can be managed in a unified manner. Context The voice service, IPTV service, and Internet access service of each user share a total user bandwidth.
Page 132: Configuring Traffic Suppression
0/2 huawei(config-if-adsl-0/2)#deactivate 0 huawei(config-if-adsl-0/2)#activate 0 template-index 10 huawei(config-if-adsl-0/2)#quit huawei(config)#traffic table ip index 10 cir 2048 pir 10240 priority 4 priority- policy local-Setting huawei(config)#service-port 100 vlan 2 adsl 0/2/0 vpi 0 vci 35 multi-service user- vlan 20 rx-cttr 10 tx-cttr 10...
Page 133 SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration Context Traffic suppression can be configured based on the port of a board. Procedure Step 1 Run the interface eth command to enter the ETH mode. Step 2 Query the thresholds of traffic suppression.
Page 134: Configuring Queue Scheduling
SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration --------------------------------------------------------------------- huawei(config-if-eth-0/3)#traffic-suppress all broadcast value 8 huawei(config-if-eth-0/3)#display traffic-suppress 0 Command: display traffic-suppress 0 Traffic suppression ID definition: --------------------------------------------------------------------- Min bandwidth(kbps) Max bandwidth(kbps) Package number(pps) --------------------------------------------------------------------- 1153 2319 4639 9265 18531...
Page 135 SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration The system supports WRR for eight queues. Each queue has a weight value (w7, w6, w5, w4, w3, w2, w1, and w0 in a descending order) for resource acquisition. In the WRR scheduling mode, the queues are scheduled in turn, which ensures that each queue can be scheduled.
Page 136: Configuring The Mapping Between The Queue And The 802.1P Priority
SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration huawei(config)#queue-scheduler wrr 10 10 20 20 10 10 10 10 huawei(config)#display queue-scheduler Queue scheduler mode : WRR --------------------------------- Queue Scheduler Mode WRR Weight --------------------------------- --------------------------------- To adopt the PQ+WRR scheduling mode and set the weight values of the six queues to 20, 20,...
Page 137: Configuring The Queue Depth
To map 802.1p priority 0 to queue 0, 802.1p priority 1 to queue 2, and the other 802.1p priorities to queue 6, do as follows: huawei(config)#cos-queue-map cos0 0 cos1 2 cos2 6 cos3 6 cos4 6 cos5 6 cos6 6 cos7...
Page 138 Step 2 Run the display queue-buffer command to query the queue depth of the current service board. ----End Example To set the queue depths to 20, 20, 10, 10, 10, 10, 10, and 10, do as follows: huawei(config)#queue-buffer 20 20 10 10 10 10 10 10 huawei(config)#display queue-buffer ------------------------ Queue...
Page 139: Configuring Traffic Management Based On Acl Rules
Step 2 Run the display qos-info traffic-limit port command to query the traffic limit information on the specified port. ----End Example To limit the traffic that matches ACL 2001 received on port 0/2/0 to 512 kbit/s, do as follows: huawei(config)#traffic-limit inbound ip-group 2001 512 port 0/2/0 huawei(config)#display qos-info traffic-limit port 0/2/0 traffic-limit: port 0/2/0: Inbound:...
Page 140: Enabling The Statistics Collection Of The Traffic Matching An Acl Rule
To add a priority tag to the traffic that matches ACL 2001 received on port 0/2/0, and the local priority of the traffic is 0 , do as follows: huawei(config)#traffic-priority inbound ip-group 2001 local-precedence 0 port 0/2/0 huawei(config)#display qos-info traffic-priority port 0/2/0...
Page 141: Enabling The Mirroring Of The Traffic Matching An Acl Rule
ACL rule on a specified port. ----End Example To mirror the traffic that matches ACL 2001 received on port 0/2/0 to port 0/0/1, do as follows: huawei(config)#traffic-mirror inbound ip-group 2001 port 0/2/0 to port 0/0/1 huawei(config)#display qos-info traffic-mirror port 0/2/0 traffic-mirror: port 0/2/0:...
Page 142: Configuring Monitoring Through The Esc
SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration 3.15.1 Configuring Monitoring Through the ESC This topic describes how to configure the H831VESC and the MiniESC on the MA5616. 3.15.1.1 Configuring the Monitoring Through the H831VESC You can monitor the environment status of the MA5616 through its built-in virtual EMU H831VESC.
Page 143 SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration Example Table 3-23 shows the parameter plan for configuring the H831VESC. Table 3-23 Data plan for configuring the H831VESC Item Data Remarks Digital Digital parameter ID: 0 In the F01S50 and F01S100 cabinets, digital...
Page 144 SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration Item Data Remarks Name of digital parameter 2: This digital parameter is set according to the Arrester actual requirements. The monitoring digital parameter of the lightning arrester status sensor is set to monitor the arrester status.
Page 145: Configuring The Monitoring Through The Escm
SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration 3.15.1.2 Configuring the Monitoring Through the ESCM The ESCM is an EMU that integrates the environment monitoring board, terminal blocks, and DIP switches. The ESCM monitors the environment parameters such as smoke, water, door status, wiring, temperature, and humidity of the device, and also provides extended monitoring ports.
Page 146 SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration Monitoring Parameter on Host Device Port Analog 2 Analog 3 Wiring JTP1 (MDF) Door0 JTM1 (door status) Digital 2 JTD1 Digital 3 JTD2 Digital 4 JTD3 Digital 5 JTD4 Digital 6...
Page 147 SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration Run the quit command to quit the miniesc mode, and then run the save command to save the data. ----End Result After the configuration, the ESCM works in the normal state and monitors the analog and digital parameters set on the MA5616.
Page 148 SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration Item Data Remarks Analog parameter ID: 2 The user-defined humidity monitoring analog parameter is added to monitor the ambient humidity of the device. For values and details of this parameter, see the esc analog command.
Page 149: Configuring Monitoring Through The Power System
16: diesel; 17: smell 18: air-condition; 19: arrester; 20: DC voltage; 21 output switch; 22: digital user-defined alarm huawei(config)#emu add 3 MINIESC 0 8 RS485 MiniESC huawei(config)#interface emu 3 huawei(config-if-miniesc-3)#esc analog 0 alarm-upper-limit 54 alarm-lower-limit 6 Send command to environment monitor board ,please waiting for the ack...
Page 150: Configuring The Monitoring Through The Eps30-4815Af
SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration 3.15.2.1 Configuring the Monitoring Through the EPS30-4815AF The EPS30-4815AF system converts the input 220 VAC into the -48 VDC to provide the -48 VDC power. In addition, the EPS30-4815AF system can manage one VRLA battery set and monitor other environment parameters through its EPMU03 monitoring module.
Page 151 SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration NOTE Before adding a user-defined analog or digital monitoring parameter, make sure that the port corresponding to this analog or digital monitoring parameter is properly connected with an environment monitoring cable.
Page 152 SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration Table 3-27 Data plan for configuring the power monitoring through the EPS30-4815AF Item Data Remarks Type: Power4830 (Pwr4830) The selected type of the EPS30-4815AF is Power4830 (Pwr4830). SN: 2 Subnode ID: 4 The DIP switch on the EPS30-4815AF is set to 4.
Page 153 SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration Item Data Remarks Battery set Battery set power-off permission You can change the configuration by power-off status: permit running the power charge command parameters according to the actual requirements. Battery set power-off voltage: 43...
Page 154 User-defined alarm ID of When the lightning arrester is faulty, the extended digital parameter 3: 19 MA5616 reports an alarm. huawei(config)#emu add 2 POWER4830 0 4 RS485 POWER4830 huawei(config)#interface emu 2 huawei(config-if-power4830-2)#display power system parameter EMU ID: 2 Power system information...
Page 155 DigitalID Name Available Level|DigitalID Name Available Level ---------------------------------------------------------------------------- huawei(config-if-power4830-2)#power battery parameter 1 0.15 60 75 huawei(config-if-power4830-2)#power module-num 2 huawei(config-if-power4830-2)#power temperature-off battery-off-state permit huawei(config-if-power4830-2)#power environment humidity 80 10 100 0 This command is invalid unless in the condition of install the sensor, would...
Page 156: Configuring The Monitoring Through The H831Pmu (Backup Power Using The Vrla Battery)
SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration module 0 : normal module 1 : normal ---------------------------------------------------------------------------- DigitalID Name Alarm State|DigitalID Name Alarm State Normal Normal Normal Normal Normal Normal Normal ---------------------------------------------------------------------------- huawei(config-if-power4830-2)#quit huawei(config)#save 3.15.2.2 Configuring the Monitoring Through the H831PMU (Backup Power Using...
Page 157 DC undervoltage alarm threshold: 48 V huawei(config)#emu add 3 H831PMU 0 0 RS485 huawei(config)#interface emu 3 huawei(config-if-h831pmu-3)#power battery parameter 1 0.15 90 12 Send command to environment monitor board ,please waiting for the ack...
Page 158: Configuring The Monitoring Through The Eps30-4815Af (Backup Power Using The Pbl 02A Fe-Lithium Battery)
SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration huawei(config-if-h831pmu-3)# Execute command successful huawei(config-if-h831pmu-3)#power charge voltage equalizing-voltage 56.8 floating- voltage 53.5 Send command to environment monitor board ,please waiting for the ack huawei(config-if-h831pmu-3)# Execute command successful huawei(config-if-h831pmu-3)#power off battery-off-state permit battery-off-voltage...
Page 159 SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration The Fe-lithium battery is connected to the input port of the power system through a power cable and connected to the MA5616 through an RS485 serial port cable. When detecting a Fe-lithium battery, the MA5616 issues a command to the power system to adjust the voltage.
Page 160: Configuring The Monitoring Through The H831Pmu (Backup Power Using The Pbl 02A Fe-Lithium Battery)
The time for installing the battery is 2010-08-20. To configure the power monitoring through the Power4830 (backup power using the Fe-lithium battery) with such configurations, do as follows: huawei(config)#emu add 2 POWER4830 0 4 RS485 POWER4830 huawei(config)#interface emu 2 huawei(config-if-power4830-2)#power module-num 2...
Page 161 SmartAX MA5616 Multi-service Access Module Configuration Guide 3 Basic Configuration Context The MA5616 supports a Fe-lithium battery set for power backup. Compared with the lead-acid battery, the Fe-lithium battery features long lifespan, large capacity, optimized discharging function, fast charging, and flexible environment adaptability. In addition, it supports intelligent management so that the battery can be automatically charged or discharged.
Page 162: Configuring The Monitoring Through The Fan
59 48 Send command to environment monitor board ,please waiting for the ack huawei(config-if-h831pmu-3)# Execute command successful huawei(config-if-h831pmu-3)#quit huawei(config)#emu add 4 liBATTERY 0 23 rs485 battery1 huawei(config)#interface emu 4 huawei(config-if-libattery-4)#power batteryinstall 2010-08-20 huawei(config-if-libattery-4)#display power run info EMU ID: 4...
Page 163 When the temperature of the fan temperature is very high: permit tray is very high, the device reports an alarm automatically. huawei(config)#emu add 1 FAN 0 2 RS485 FAN huawei(config)#interface emu 1 huawei(config-if-fan-1)#fan speed mode automatic huawei(config-if-fan-1)#fan alarmset block permit...
Page 164: Configuring The Ethernet Cfm Oam
SmartAX MA5616 Multi-service Access Module Configuration Guide 4 Configuring the Ethernet CFM OAM Configuring the Ethernet CFM OAM On the Ethernet network, Ethernet connectivity fault management (CFM) OAM is defined as connectivity fault management in IEEE 802.1ag to implement the OAM function of connectivity detection on the Ethernet bearer network.
Page 165 SmartAX MA5616 Multi-service Access Module Configuration Guide 4 Configuring the Ethernet CFM OAM Procedure Step 1 Create a VLAN. Run the vlan command to create a VLAN that is associated with the object managed by a maintenance association (MA). Each MA corresponds to one VLAN. The Ethernet CFM checks the connectivity for each MA.
Page 166 MA5616_A: VLAN 10 is associated with the MA; the MEP port is 0/0/0; the local MEP is 0/0/1; the remote MEP is 0/0/2; the name of the object managed by the MA is huawei-1; the name of the object managed by the MD is huawei; the level of the object managed by the MD is 7.
Page 167 10 smart //Create a VLAN that is associated with the MA. huawei(config)#port vlan 10 0/0 0 huawei(config)#cfm md 0 name-format string huawei level 7 huawei(config)#cfm ma 0/0 name-format string huawei-1 huawei(config)#cfm ma 0/0 vlan 10 huawei(config)#cfm ma 0/0 meplist 1...
Page 168: Configuring The Xdsl Internet Access Service
SmartAX MA5616 Multi-service Access Module Configuration Guide 5 Configuring the xDSL Internet Access Service Configuring the xDSL Internet Access Service About This Chapter xDSL broadband Internet access is applicable in the scenario where the Internet service is provided through the ordinary twisted pairs. In this scenario, a user can access Internet in IPoE, PPPoE, IPoA, PPPoA, or 802.1X mode.
Page 169 SmartAX MA5616 Multi-service Access Module Configuration Guide 5 Configuring the xDSL Internet Access Service Data preparation Before configuring an xDSL Internet access service, plan the data items as listed in Table 5-1. Table 5-1 Data plan for the xDSL Internet access service...
Page 170 SmartAX MA5616 Multi-service Access Module Configuration Guide 5 Configuring the xDSL Internet Access Service Item Data Remarks BRAS The BRAS performs the related configurations according to the authentication and accounting requirements for dial-up users. For example, the BRAS configures the...
Page 171: Configuring A Vlan
SmartAX MA5616 Multi-service Access Module Configuration Guide 5 Configuring the xDSL Internet Access Service 5.1 Configuring a VLAN Configuring VLAN is a prerequisite for configuring a service. Hence, before configuring a service, make sure that the VLAN configuration based on planning is complete.
Page 172 SmartAX MA5616 Multi-service Access Module Configuration Guide 5 Configuring the xDSL Internet Access Service Table 5-3 Default parameter settings of VLAN Parameter Default Setting Remarks Default VLAN of VLAN ID: 1 the system Type: smart VLAN Reserved VLAN VLAN ID range:...
Page 173 SmartAX MA5616 Multi-service Access Module Configuration Guide 5 Configuring the xDSL Internet Access Service VLAN Configuration VLAN Description Application Scenario Type Command To add a MUX VLAN, One MUX VLAN may MUX VLANs are VLAN run the vlan vlanid contain multiple applicable to FE or mux command.
Page 174 SmartAX MA5616 Multi-service Access Module Configuration Guide 5 Configuring the xDSL Internet Access Service Configuration VLAN Type VLAN Application Command Description Scenario Attri bute QinQ To configure QinQ The VLAN with The packets from a Applicable to the as the attribute of a...
Page 175 SmartAX MA5616 Multi-service Access Module Configuration Guide 5 Configuring the xDSL Internet Access Service Configuration VLAN Type VLAN Application Command Description Scenario Attri bute To configure The VLAN with The packets from a Applicable to the stacking as the this attribute can...
Page 176: Configuring An Upstream Port
SmartAX MA5616 Multi-service Access Module Configuration Guide 5 Configuring the xDSL Internet Access Service NOTE l To configure attributes for the VLANs with consecutive IDs in batches, run the vlan attrib vlanid to end- vlanid command. l To configure attributes for the VLANs with inconsecutive IDs in batches, run the vlan attrib vlan-list command.
Page 177: Configuring An Xdsl Port
0 100 huawei(config-if-eth-0/0)#speed 1 100 huawei(config-if-eth-0/0)#quit huawei(config)#link-aggregation 0/0 0 0/0 1 egress-ingress workmode lacp-static 5.3 Configuring an xDSL Port An xDSL can transmit services only when it is activated. This topic describes how to activate an xDSL port and bind the port with an xDSL profile.
Page 178 SmartAX MA5616 Multi-service Access Module Configuration Guide 5 Configuring the xDSL Internet Access Service activated state of a port. That is, services can be transmitted between the xDSL port and the xTU-R. If the xTU-R is online (powered on), the activating process is completed after the training is successful.
Page 179: Creating An Xdsl Service Port
SmartAX MA5616 Multi-service Access Module Configuration Guide 5 Configuring the xDSL Internet Access Service NOTE To activate a port, you must bind the port with a line template. If you do not specify the index of the line template, the system uses the template bound with the port last time to activate the port.
Page 180 SmartAX MA5616 Multi-service Access Module Configuration Guide 5 Configuring the xDSL Internet Access Service Table 5-6 Default settings of a service port Parameter Default Setting Traffic profile ID Administration status Activated Maximum number of learnable MAC addresses Procedure Step 1 Add a traffic profile.
Page 181 SmartAX MA5616 Multi-service Access Module Configuration Guide 5 Configuring the xDSL Internet Access Service Select multi-service user-8021p user-8021p [ user-vlan user-vlanid ]. – By VLAN + user-side service encapsulation mode (user-encap) Select multi-service user-vlan { untagged | user-vlanid | priority-tagged } user- encap user-encap.
Page 182 : 198608 bytes Referenced Status : not used ------------------------------------------------ huawei(config)#service-port 3 vlan 100 adsl 0/2/0 vpi 1 vci 39 inbound traffic- table index 8 outbound traffic-table index 8 huawei(config)#mac-address max-mac-count service-port 3 2 huawei(config)#service-port 3 adminstatus disable A residential user requests the Internet access service with the access rate 2048 kbit/s. To...
Page 183 3072 100304 6144 198608 local-pri ---------------------------------------------------------------------------- Total Num : 8 huawei(config)#traffic table ip index 9 cir 8192 priority 4 priority-policy loca l-Setting Create traffic descriptor record successfully ------------------------------------------------ TD Index TD Name : ip-traffic-table_9 Priority Mapping Priority Mapping Index...
Page 184: Optional) Configuring The Xpoa-Xpoe Protocol Conversion
SmartAX MA5616 Multi-service Access Module Configuration Guide 5 Configuring the xDSL Internet Access Service 5.5 (Optional) Configuring the xPoA-xPoE Protocol Conversion Configuring protocol conversion is required only when the encapsulation mode is IPoA or PPPoA; it is not required when the encapsulation mode is IPoE or PPPoE.
Page 185 SmartAX MA5616 Multi-service Access Module Configuration Guide 5 Configuring the xDSL Internet Access Service Table 5-7 Default settings of the xPoA-xPoE protocol conversion Parameter Default Setting Maximum number of the MAC addresses in the MAC address pool Status of the IPoA-IPoE protocol conversion...
Page 186 10.1.1.1 huawei(config)#encapsulation 0/2/0 vpi 0 vci 35 type ipoa llc srcIP 10.1.1.20 The PPPoA service encapsulation mode is LLC. To enable the PPPoA-PPPoE protocol conversion with the start MAC address 0000-1010-1000 in the MAC address pool that contains...
Page 187: Configuring The Multicast Service (Multicast Vlan Mode)
SmartAX MA5616 Multi-service Access Module Configuration Guide 6 Configuring the Multicast Service (Multicast VLAN Mode) Configuring the Multicast Service (Multicast VLAN Mode) About This Chapter This topic describes how to configure the multicast service on the MA5616 in multicast VLAN mode.
Page 188: Default Settings Of The Multicast Service
SmartAX MA5616 Multi-service Access Module Configuration Guide 6 Configuring the Multicast Service (Multicast VLAN Mode) 6.1 Default Settings of the Multicast Service This topic provides the default settings of the multicast service in the system, including the configuration of multicast protocol, IGMP version, program configuration mode, bandwidth management, program preview, and log function.
Page 189: Configuring Global Multicast Parameters
SmartAX MA5616 Multi-service Access Module Configuration Guide 6 Configuring the Multicast Service (Multicast VLAN Mode) Table 6-2 Data plan for configuring the multicast service on a standalone MA5616 Device Item Remarks MA5616 Multicast VLAN Generally, a multicast VLAN is allocated to each multicast ISP.
Page 190 SmartAX MA5616 Multi-service Access Module Configuration Guide 6 Configuring the Multicast Service (Multicast VLAN Mode) Purpose: A general query packet is periodically sent by the MA5616 to check whether there is any multicast user who leaves the multicast group without sending the leave packet.
Page 191 SmartAX MA5616 Multi-service Access Module Configuration Guide 6 Configuring the Multicast Service (Multicast VLAN Mode) Step 5 Run the display igmp config global command to check whether the parameters are configured correctly. ----End Example To configure multicast general query parameters by setting the query interval to 150s, maximum...
Page 192: Configuring The Multicast Program
SmartAX MA5616 Multi-service Access Module Configuration Guide 6 Configuring the Multicast Service (Multicast VLAN Mode) 6.2.2 Configuring the Multicast Program A multicast program can be configured statically or generated dynamically. After the program is configured, the multicast user with the corresponding rights can watch or preview the program.
Page 193 SmartAX MA5616 Multi-service Access Module Configuration Guide 6 Configuring the Multicast Service (Multicast VLAN Mode) Dynamic generation mode: A program is generated according to the request of the user. In this mode, the program list is not required; however, the functions such as program management, user multicast bandwidth management, program preview, and program prejoin are not supported.
Page 194 This operation will delete all the programs in current multicast vlan Are you sure to change current match mode? (y/n)[n]: y Command is being executed, please wait... Command has been executed successfully huawei(config-mvlan10)#igmp program add name movie ip 224.1.1.1 sourceip 10.10.10.10 hostip 10.0.0.254 bandwidth 5000 huawei(config-mvlan10)#igmp uplink-port 0/0/1...
Page 195 Are you sure to change current match mode? (y/n)[n]: y Command is being executed, please wait... Command has been executed successfully huawei(config-mvlan10)#igmp match group ip 224.1.1.1 to-ip 224.1.1.100 huawei(config-mvlan10)#igmp uplink-port 0/0/1 huawei(config-mvlan10)#igmp mode proxy Are you sure to change IGMP mode?(y/n)[n]:y...
Page 196: Configuring The Multicast User
SmartAX MA5616 Multi-service Access Module Configuration Guide 6 Configuring the Multicast Service (Multicast VLAN Mode) Query the attributes and information of the program in the multicast VLAN in dynamic generation mode. huawei(config-mvlan10)#display igmp config vlan 10 ---------------------------------------------------------------------- IGMP mode : proxy...
Page 197 SmartAX MA5616 Multi-service Access Module Configuration Guide 6 Configuring the Multicast Service (Multicast VLAN Mode) l Run the igmp user add service-port index max-program command to configure the maximum number of programs that can be concurrently watched by the multicast user.
Page 198: Optional) Configuring The Multicast Bandwidth
Result Check whether the multicast user is configured correctly. huawei(config)#display igmp user 0 //0 is the index of the multicast user. You can run the display igmp user all command to query the index of the multicast user. { <cr>||<K> }:...
Page 199 Mbit/s, and the bandwidth of the multicast program with IP address 224.1.1.1 is 1 Mbit/s. To perform the configurations, do as follows: huawei(config)#btv huawei(config-btv)#igmp bandwidthcAC enable huawei(config-btv)#igmp user add service-port 0 max-bandwidth 10240 //0 is the service port ID of the multicast user. huawei(config-btv)#multicast-vlan 10 huawei(config-mvlan10)#igmp program add ip 224.1.1.1 bandwidth 1024...
Page 200 SmartAX MA5616 Multi-service Access Module Configuration Guide 6 Configuring the Multicast Service (Multicast VLAN Mode) Result Check whether the bandwidths of the multicast user and multicast program are configured correctly. Check whether the bandwidth of the multicast user is configured correctly.
Page 201 SmartAX MA5616 Multi-service Access Module Configuration Guide 6 Configuring the Multicast Service (Multicast VLAN Mode) 0.00 Total video bandwidth Mcast video bandwidth Check whether the bandwidth of the multicast program is configured correctly. huawei(config)#display igmp program all { <cr>|| <K> }:...
Page 202: Optional) Configuring The Multicast Preview
SmartAX MA5616 Multi-service Access Module Configuration Guide 6 Configuring the Multicast Service (Multicast VLAN Mode) Program Grade --------------------------------------------- 6.2.5 (Optional) Configuring the Multicast Preview Multicast preview is an advertising method provided by carriers for ISPs. The purpose is to allow users to have an overview of a program so that the user can determine whether to request for the program.
Page 203 224.1.1.1 is added, and other parameters use the default values. To perform the configurations, do as follows: huawei(config)#btv huawei(config-btv)#igmp preview enable huawei(config-btv)#igmp preview-profile add index 1 duration 150 times 10 huawei(config-btv)#quit huawei(config)#multicast-vlan 10 huawei(config-mvlan10)#igmp program add ip 224.1.1.1 preview-profile 1 Result Check whether the preview function of the multicast program is configured correctly.
Page 204 SmartAX MA5616 Multi-service Access Module Configuration Guide 6 Configuring the Multicast Service (Multicast VLAN Mode) V2 router present timeout(s) User action report switch disable Preview switch : enable //The multicast preview function is enabled. Recognition time(s) The time of reset preview-count...
Page 205: Optional) Configuring The Program Prejoin
SmartAX MA5616 Multi-service Access Module Configuration Guide 6 Configuring the Multicast Service (Multicast VLAN Mode) The queried program index is 0. huawei(config)#display igmp program index 0 { <cr>|| <K> }: Command: display igmp program index --------------------------------------------- Program index Create mode...
Page 206 To enable the program prejoin function when adding a program whose IP address is 224.1.1.1, do as follows: huawei(config)#multicast-vlan 10 huawei(config-mvlan10)#igmp program add ip 224.1.1.1 prejoin enable Result Query the status of the program prejoin function and unsolicited report function.
Page 207: Optional) Configuring The Multicast Log
SmartAX MA5616 Multi-service Access Module Configuration Guide 6 Configuring the Multicast Service (Multicast VLAN Mode) Command: display igmp program index 0 --------------------------------------------- Program index Create mode : static Program name : PROGRAM-0 IP address : 224.1.1.1 VLAN ID : 10...
Page 208 SmartAX MA5616 Multi-service Access Module Configuration Guide 6 Configuring the Multicast Service (Multicast VLAN Mode) The MA5616 can report the multicast log to the log server in syslog mode or in call detailed record (CDR) mode. By default, the MA5616 reports the log in syslog mode.
Page 209 SmartAX MA5616 Multi-service Access Module Configuration Guide 6 Configuring the Multicast Service (Multicast VLAN Mode) – After the multicast log report function in CDR mode is enabled, the MA5616 reports local multicast logs to the multicast log server in the form of a file.
Page 210: Configuring The Multicast Service On A Subtending Network
SmartAX MA5616 Multi-service Access Module Configuration Guide 6 Configuring the Multicast Service (Multicast VLAN Mode) Auto create log interval(h) Uplink port mode : default Bandwidth management switch : enable CDR auto report interval(s) : 600 CDR auto report number : 200...
Page 211 SmartAX MA5616 Multi-service Access Module Configuration Guide 6 Configuring the Multicast Service (Multicast VLAN Mode) Figure 6-1 Example network of the multicast service in subtending networking mode Multicast source ISP2 ISP1 Router MA5616_A MA5616_B user1 user2 Data Plan Table 6-3 provides the data plan for configuring the multicast service in subtending networking mode.
Page 212 SmartAX MA5616 Multi-service Access Module Configuration Guide 6 Configuring the Multicast Service (Multicast VLAN Mode) Device Item Data Subtending 0/0/0 port IGMP version IGMP V3 (default multicast version of the system in multicast VLAN mode) Multicast There are two multicast sources, namely, ISP 1 and ISP 2.
Page 213 You cannot name a program, instead the system automatically names a program PROGRAM-M, in which M is the index of the added program. huawei(config-mvlan4002)#igmp program add name program1 ip 224.1.1.1 sourceip 10.10.10.10 huawei(config-mvlan4002)#multicast-vlan 4003 huawei(config-mvlan4003)#igmp program add name program2 ip 224.1.1.2 sourceip 10.10.10.11...
Page 214 4002-4005 smart huawei(config)#port vlan 4002-4005 0/0 0 Configure service ports. huawei(config)#service-port 100 vlan 4004 vdsl mode ptm 0/1/0 multi- service user-vlan untagged rx-cttr 6 tx-cttr 6 huawei(config)#service-port 101 vlan 4005 vdsl mode ptm 0/1/1 multi- service user-vlan untagged rx-cttr 6 tx-cttr 6 Configure multicast VLANs and the IGMP mode.
Page 215 SmartAX MA5616 Multi-service Access Module Configuration Guide 6 Configuring the Multicast Service (Multicast VLAN Mode) Result User 1 belongs to multicast VLAN 4002 and user 1 can watch the program with IP address 224.1.1.1 provided by ISP1. User 2 belongs to multicast VLAN 4003 and user 2 can watch the program with IP address 224.1.1.2 provided by ISP2.
Page 216 SmartAX MA5616 Multi-service Access Module Configuration Guide 6 Configuring the Multicast Service (Multicast VLAN Mode) igmp user add service-port 100 igmp user add service-port 101 multicast-vlan 4002 igmp multicast-vlan member service-port 100 multicast-vlan 4003 igmp multicast-vlan member service-port 101 quit...
Page 217: Configuring The Voice Service
SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service Configuring the Voice Service About This Chapter The MA5616 supports user access through copper cables to provide the voice service. Context The MA5616 can provide the voice service through the H.248 or Session Initiation Protocol (SIP) protocol.
Page 218 SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service Dual homing Supports dual homing from the MG to the MGC through the H.248 protocol and authentication from the SIP AG to the SIP proxy server through the SIP protocol.
Page 219: Configuring The Voip Pstn Service (Based On The H.248 Protocol)
SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service 7.1 Configuring the VoIP PSTN Service (Based on the H.248 Protocol) This topic describes how to configure the VoIP PSTN service on the MA5616 when the H.248 protocol is used.
Page 220 SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service Table 7-1 Data plan for configuring the VoIP PSTN service based on the H.248 protocol Item Remarks MG interface Parameter Media and It is used as the upstream VLAN of the...
Page 221 SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service Item Remarks Domain name of It corresponds to parameter the MG interface domainName of the MG interface. When the H.248 protocol is used, this parameter must be configured if parameter MIDType of the H.248...
Page 222 SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service Item Remarks TID Format of an MG The TID format determines the Interface generation mode of various types of user terminals on an MG interface. Voice service Slot that houses the voice...
Page 223: Configuring An Mg Interface
SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service Item Remarks Overseas Parameters The attributes such as the upper and lower thresholds of the flash-hooking duration need to be configured according to the local standards to ensure that the response of the user terminal complies with the local standards.
Page 224: Configuring The Upstream Vlan Interface
3 vlanif3 current state : UP Line protocol current state : UP Description : HUAWEI, SmartAX Series, vlanif3 Interface The Maximum Transmit Unit is 1500 bytes Internet Address is 10.13.4.116/16 Internet Address is 10.13.4.117/16 Secondary IP Sending Frames' Format is PKTFMT_ETHNT_2, Hardware address is 00e0-fc32-1118 7.1.1.2 Configuring the Media and Signaling IP Address Pools...
Page 225 SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service Prerequisites The IP address of the L3 interface of the media and signaling upstream VLAN must be configured. For details about how to configure the IP address, see 7.1.1.1 Configuring the...
Page 226: Adding An Mg Interface
SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service MAC Address..: 00-E0-FC-AF-91-33 IP Address...: 10.13.4.117 Subnet Mask..: 255.255.0.0 Gateway....: 10.13.1.1 MAC Address..: 00-E0-FC-AF-91-33 huawei(config-voip)#display ip address signaling Signaling: IP Address...: 10.13.4.116 Subnet Mask..: 255.255.0.0 MAC Address..: 00-E0-FC-AF-91-33 IP Address...: 10.13.4.117...
Page 227 MGC. Generally, UDP is used. start-negotiate-version If the MGC connecting to the MG is a Huawei device, the profile (parameter profile-index) does not need to be set; if the MGC connecting to the MG is a device of another...
Page 228: Optional) Configuring The Digitmap Of An Mg Interface
SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service MG signalling Port 2944 MG media IP1 10.71.46.69 MG media IP2 10.13.4.117 MIDType IP4_ADDR DeviceName Retrans Enable Active MGC MGC Port :2944 MGC IP1:10.13.2.118 Active MGC MGC Port...
Page 229 SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service Table 7-3 Digitmap format in the H.248 protocol Digit or Description Character Indicate dialed digits 0-9. Indicate A-D. Indicates * in the DTMF mode. Indicates for # in the DTMF mode.
Page 230: Optional) Configuring The Software Parameters Of An Mg Interface
SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service Step 4 Check whether the configuration of the digitmap timer is the same as that in the data plan. l Run the display digitmap command to check whether the digitmap is configured correctly.
Page 231 SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service Table 7-4 Software parameters of an MG interface that supports H.248 Parameter Description Default Setting Indicates whether the MG Numeral type. Range: 0-2. interface supports dual homing. l 0: Indicates that dual homing To configure an MG interface is not supported.
Page 232 SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service Parameter Description Default Setting Indicates whether a wildcard is Numeral type. Range: 0-1. used for the registration of the l 0: Indicates that a wildcard is MG interface.
Page 233 SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service Parameter Description Default Setting Indicates whether the MG Numeral type. Range: 0-1. interface supports security l 0: Indicates that security header. header is supported. To configure an MG interface...
Page 234 SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service Parameter Description Default Setting Indicates the maximum Numeral type. Range: 0-1. digitmap matching flag of the l 0: Indicates that the match MG interface. follows the protocol. To configure digitmap...
Page 235 SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service Parameter Description Default Setting Indicates the length of the timer Numeral type. Range: 0-30s. for filtering the media stream Default: 5s source port of the MG interface. To configure the length of the...
Page 236 SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service Parameter Description Default Setting Indicates the type of remote Numeral type. Range: 0-4. blocking play tone. l 0: Indicates the busy tone. l 1: Indicates the device congestion tone.
Page 237 SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service Parameter Description Default Setting Indicates whether the MG Numeral type. Range: 0-1. actively establishes or releases l 0: Yes the link for the BRA user after l 1: No the MGC initiates the in-service or OOS request.
Page 238: Optional) Configuring The Ringing Mode Of An Mg Interface
SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service Example To configure software parameter 11 of H.248-based MG interface 0 to 1 so that the MG interface supports emergency standalone and allows only internal calls, do as follows:...
Page 239 0 (the values of the corresponding parameters cadence and initialring are 128 and 144 respectively). To configure the ringing mode of MG interface 0, do as follows: huawei(config)#user defined-ring modify 0 para1 400 para2 200 para3 400 para4 2000 huawei(config)#display user defined-ring --------------------------------------------------...
Page 240: Optional) Configuring The Tid Format Of An Mg Interface
SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service Command: display mg-ringmode attribute ------------------------------------------------------- MGID PeerPara CadenceRing InitialRing ------------------------------------------------------- ------------------------------------------------------- 7.1.1.7 (Optional) Configuring the TID Format of an MG Interface The TID format determines how various user terminal IDs on the MG interface are generated.
Page 241 SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service template that is bound to the type of users. Then, run the display tid-template command to check whether the TID template supports the layering configuration. Hence, you can check whether the user supports terminal layering.
Page 242: Enabling An Mg Interface
TID template 3 is used. To add a PSTN user on port 0/2/0 and check whether the system automatically allocates a TID generated according to the template, do as follows: huawei(config)#display tid-template 3// Query the information about the TID template 3.
Page 243: Configuring The Voip Pstn User
SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service l Run the display if-h248 state command to check whether the MG interface is in the normal state. l Run the quit command to quit the global config mode, and then run the display if-h248 all command to check whether the MG interface is in the normal state.
Page 244 SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service Parameter Default Setting Whether to support the detection of Not support the ANSbar signal through monophony Whether to support the bell ANS Not support signal Power-off interval 100 ms...
Page 245 To add the PSTN users in slot 0/3 on MG interface 0 in batches, do as follows: huawei(config)#board confirm 0/3 huawei(config)#esl user huawei(config-esl-user)#mgpstnuser batadd 0/3/0 0/3/31 0 terminalid 0 telno 83110000 huawei(config-esl-user)#display mgpstnuser 0 0 32 ------------------------------------------------------------------------...
Page 246: Optional) Configuring The System Parameters
SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service /3 /31 83110031 Cat3 ------------------------------------------------------------------------ 7.1.2.2 (Optional) Configuring the System Parameters This topic describes how to configure the system parameters including the overseas version flag and message waiting indication (MWI) mode according to the local standards to ensure that the response of the user terminal complies with the local standards.
Page 247: Optional) Configuring The Overseas Parameters
SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service ----------------------------------------------------------------------------- Parameter name index: 1 Parameter value: 1 Mean: Overseas version flag, 0:China, 1:HongKong, 2:Brazil, 3:Egypt, 4: Singapore, 5:Thailand, 6:France, 7:Britain MSFUK, 8:Britain ETSI, 9:Bulgaria, 14:Turkey, 20:Germany ----------------------------------------------------------------------------- 7.1.2.3 (Optional) Configuring the Overseas Parameters...
Page 248: Optional) Configuring The Local Digitmap
SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service display oversea parameters ----------------------------------------------------------------------------- Parameter name index: 0 Parameter value: 800 Mean: Hooking upper threshold(ms), reference: China:350, HongKong:800 ----------------------------------------------------------------------------- Parameter name index: 1 Parameter value: 100 Mean: Hooking lower threshold(ms), reference: China:100, HongKong:100...
Page 249 SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service The MA5616 supports a maximum of eight local digitmaps. For the meaning of each character in the digitmap body, see the Context in 7.1.1.4 (Optional) Configuring the Digitmap of an MG Interface.
Page 250 SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service Name: huawei Body: ([2-8]xxxxxxx|[2-8]xxSxxxxxxx|13xxxxxxxxx|0xxxxxxxxx|9xxxx|1[0124-9]x|F| x.F|[0-9].S) ------------------------------------------ Assume that the SIP protocol is used on the MA5616. The local digitmap exists in the system. Table 7-10 lists the data of the local digitmap.
Page 251: Optional) Configuring The Attributes Of A Pstn Port
SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service Name: DefaultEmergencyDmm Type: emergency Body: (11X|91X) ------------------------------------------ Name: huawei0 Type: normal Body: ([2-8]xxxxxxx|[2-8]xxSxxxxxxx|13xxxxxxxxx|0xxxxxxxxx|9xxxx|1[0124-9]x|F| x.F|[0-9].S|15xxxxxxxxx) ------------------------------------------ Name: huawei1 Type: emergency Body: (11X|91X|0E) ------------------------------------------ 7.1.2.5 (Optional) Configuring the Attributes of a PSTN Port This topic describes how to configure the attributes of a PSTN port to ensure that the PSTN port can meet the actual application requirements.
Page 252: Optional) Configuring The Attributes Of The Ringing Current
To set the ringing current frequency to 16 Hz (parameter value 0) and AC amplitude to 65 Vrms (parameter value 1), do as follows: huawei(config)#voip huawei(config-voip)#ring attribute set frequency 0 acamplitude 1 huawei(config-voip)#display ring attribute ringing current frequency : 16Hz ringing current acamplitute: 65Vrms 7.2 Configuring the VoIP PSTN Service (Based on the SIP...
Page 253 SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service Context The voice over IP (VoIP) service uses the IP packet switching network for transmission after the traditional analog voice signals are compressed and packetized, to reduce the cost of the voice service.
Page 254 SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service Item Remarks Default IP address It is the IP address of the next hop from of the MG the MA5616 to the IMS core network device. CAUTION If the media IP address and the signaling IP...
Page 255 SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service Item Remarks Voice service Slot that houses the voice data service board (The data User Data Phone number The phone number that the IMS core configuration network device allocates to the user must be must be configured.
Page 256: Configuring The Sip Interface
SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service Item Remarks Local Digitmap Configure a proper local digitmap according to the local standards. After the configuration, the local digitmap can be directly used to match the phone number after the user picks the phone off the hook.
Page 257: Configuring The Media And Signaling Ip Address Pools
3 vlanif3 current state : UP Line protocol current state : UP Description : HUAWEI, SmartAX Series, vlanif3 Interface The Maximum Transmit Unit is 1500 bytes Internet Address is 10.13.4.116/16 Internet Address is 10.13.4.117/16 Secondary IP Sending Frames' Format is PKTFMT_ETHNT_2, Hardware address is 00e0-fc32-1118 7.2.1.2 Configuring the Media and Signaling IP Address Pools...
Page 258 SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service Context The media IP address and the signaling IP address for the MG or SIP interface must be selected from the IP address pools configured here. The signaling IP address pool is used to store the IP addresses of the MG or SIP interfaces, and the media IP address pool is used to store the IP addresses of the media streams controlled by the signaling.
Page 259: Adding An Sip Interface
SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service IP Address...: 10.13.4.116 Subnet Mask..: 255.255.0.0 MAC Address..: 00-E0-FC-AF-91-33 IP Address...: 10.13.4.117 Subnet Mask..: 255.255.0.0 MAC Address..: 00-E0-FC-AF-91-33 7.2.1.3 Adding an SIP Interface This topic describes how to add an SIP interface so that the MA5616 can communicate with the IMS through the SIP interface.
Page 260 IP address 1 of the secondary proxy server is 10.13.4.119, port ID of the secondary proxy server is 5060, home domain name is sip.huawei.com, and profile index is 1. To configure such attributes of SIP interface 0, do as follows: huawei(config)#interface sip 0 huawei(config)#if-sip attribute basic media-ip 10.13.4.116 signal-ip...
Page 261: Optional) Configuring The Ringing Mode Of The Sip Interface
SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service MGID Signalling IP 10.13.4.117 Signalling Port 5000 Media IP 10.13.4.116 Transfer Mode Primary Proxy IP 1 10.13.4.118 Primary Proxy IP 2 Primary Proxy Port 5060 Secondary Proxy IP 1 10.13.4.119...
Page 262 SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service Context If the preset ringing modes of the system can meet the user requirements, you can select the required ringing mode and configure the corresponding ringing mapping. If the preset ringing modes cannot meet the user requirements, you can use the user-defined ringing mode and configure the corresponding ringing mapping.
Page 263: Configuring The Voip Pstn User
Cadence ringing mode: 1 Initial ringing mode: 4 To add such a ringing mode mapping record on SIP interface 0, do as follows: huawei(config)#interface sip 0 huawei(config-if-sip-0)#ringmode add 1 alter-group cadencering 1 initialring 4 huawei(config-if-sip-0)#display ringmode 1 ----------------------------------------------------------------- MGID: 0...
Page 264 SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service Parameter Default Setting Format of the phone number of the SDMF(FSK) calling party Power-off interval 100ms FSK delay interval 800ms Whether to enable or disable VQE Disable automatic gain...
Page 265: Configuring The Centrex
SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service CAUTION When adding a user, you can configure the phone number (parameter telno). When the public ID is generated by phone number, you must enter the phone number. It is recommended that you configure this phone number to be the same as the phone number configured on the IMS.
Page 266 SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service – Similarity: When the members in a centrex need to call the members outside of the centrex, they must dial the centrex prefix. – Difference: If the centrex attribute is set to two-stage centrex, the members in a centrex can hear the dial tone again after dialing the centrex prefix.
Page 267 SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service Configure the centrex call function by using method 2 in Precaution: In global config mode, run the local-digitmap add command to configure a direct centrex digitmap or a two-stage centrex digitmap.
Page 268: Optional) Configuring The System Parameters
SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service 7.2.2.3 (Optional) Configuring the System Parameters This topic describes how to configure the system parameters including the overseas version flag and message waiting indication (MWI) mode according to the local standards to ensure that the response of the user terminal complies with the local standards.
Page 269: Optional) Configuring The Overseas Parameters
SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service Singapore, 5:Thailand, 6:France, 7:Britain MSFUK, 8:Britain ETSI, 9:Bulgaria, 14:Turkey, 20:Germany ----------------------------------------------------------------------------- 7.2.2.4 (Optional) Configuring the Overseas Parameters By default, the overseas parameters are configured according to the Chinese standards. In the...
Page 270: Optional) Configuring The Local Digitmap
SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service Mean: Hooking upper threshold(ms), reference: China:350, HongKong:800 ----------------------------------------------------------------------------- Parameter name index: 1 Parameter value: 100 Mean: Hooking lower threshold(ms), reference: China:100, HongKong:100 ----------------------------------------------------------------------------- Parameter name index: 2 Parameter value: 0...
Page 271 SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service For the meaning of each character in the digitmap body, see the Context in 7.1.1.4 (Optional) Configuring the Digitmap of an MG Interface. Precaution When the H.248 protocol is used, the type of the local digitmap can only be normal.
Page 272 SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service Body: ([2-8]xxxxxxx|[2-8]xxSxxxxxxx|13xxxxxxxxx|0xxxxxxxxx|9xxxx|1[0124-9]x|F| x.F|[0-9].S) ------------------------------------------ Assume that the SIP protocol is used on the MA5616. The local digitmap exists in the system. Table 7-18 lists the data of the local digitmap.
Page 273: Optional) Configuring The Attributes Of A Pstn Port
SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service Type: emergency Body: (11X|91X) ------------------------------------------ Name: huawei0 Type: normal Body: ([2-8]xxxxxxx|[2-8]xxSxxxxxxx|13xxxxxxxxx|0xxxxxxxxx|9xxxx|1[0124-9]x|F| x.F|[0-9].S|15xxxxxxxxx) ------------------------------------------ Name: huawei1 Type: emergency Body: (11X|91X|0E) ------------------------------------------ 7.2.2.6 (Optional) Configuring the Attributes of a PSTN Port This topic describes how to configure the attributes of a PSTN port to ensure that the PSTN port can meet the actual application requirements.
Page 274: Optional) Configuring The Attributes Of The Ringing Current
To set the ringing current frequency to 16 Hz (parameter value 0) and AC amplitude to 65 Vrms (parameter value 1), do as follows: huawei(config)#voip huawei(config-voip)#ring attribute set frequency 0 acamplitude 1 huawei(config-voip)#display ring attribute ringing current frequency : 16Hz ringing current acamplitute: 65Vrms 7.3 Configuring the VoIP ISDN BRA Service...
Page 275 SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service Prerequisites According to the actual network, a route from the MA5616 to the MGC must be configured to ensure that the MA5616 communicates with the MGC normally. Context The voice over IP (VoIP) service uses the IP packet switched network for transmission after the traditional analog voice signals are compressed and packetized.
Page 276 SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service Table 7-20 Data plan for configuring the H.248-based VoIP ISDN BRA service Item Remarks MG interface data Parameters of Upstream It is used as the upstream VLAN the media...
Page 277 SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service Item Remarks Coding mode Currently, only the text mode is of the MG supported. interface Transmission The transmission mode is mode of the selected according to the MG interface requirements of the MGC.
Page 278 SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service Item Remarks Software parameters of the Whether the MG interface MG interface supports the functions such as dual homing and emergency standalone is determined by the service requirements.
Page 279 SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service Item Remarks Remote IP It must be the same as the local IP address address of the link configured on the MGC. The SCTP protocol supports the multi-homing function.
Page 280: Configuring An Mg Interface
SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service Item Remarks System parameters The system parameters including the oversea version flag and message waiting indication (MWI) mode need to be configured according to the local standards to ensure that the response of the user terminal complies with the local standards.
Page 281: Configuring The Media And Signaling Ip Address Pools
3 vlanif3 current state : UP Line protocol current state : UP Description : HUAWEI, SmartAX Series, vlanif3 Interface The Maximum Transmit Unit is 1500 bytes Internet Address is 10.13.4.116/16 Internet Address is 10.13.4.117/16 Secondary IP Sending Frames' Format is PKTFMT_ETHNT_2, Hardware address is 00e0-fc32-1118 7.3.1.2 Configuring the Media and Signaling IP Address Pools...
Page 282 SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service Context The media IP address and the signaling IP address for the MG or SIP interface must be selected from the IP address pools configured here. The signaling IP address pool is used to store the IP addresses of the MG or SIP interfaces, and the media IP address pool is used to store the IP addresses of the media streams controlled by the signaling.
Page 283: Adding An Mg Interface
SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service IP Address...: 10.13.4.116 Subnet Mask..: 255.255.0.0 MAC Address..: 00-E0-FC-AF-91-33 IP Address...: 10.13.4.117 Subnet Mask..: 255.255.0.0 MAC Address..: 00-E0-FC-AF-91-33 7.3.1.3 Adding an MG Interface This topic describes how to add an MG interface, through which the MA5616 can communicate with the MGC.
Page 284 MGC. Generally, UDP is used. start-negotiate-version If the MGC connecting to the MG is a Huawei device, the profile (parameter profile-index) does not need to be set; if the MGC connecting to the MG is a device of another...
Page 285: Optional) Configuring The Digitmap Of An Mg Interface
SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service Retrans Enable Active MGC MGC Port :2944 MGC IP1:10.13.2.118 Active MGC MGC Port :2944 MGC IP2:- Active MGC MGC Domain Name:- Standby MGC MGC Port IP1:- Standby MGC...
Page 286 SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service Table 7-22 Digitmap format in the H.248 protocol Digit or Description Character Indicate dialed digits 0-9. Indicate A-D. Indicates * in the DTMF mode. Indicates for # in the DTMF mode.
Page 287: Optional) Configuring The Software Parameters Of An Mg Interface
SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service Step 4 Check whether the configuration of the digitmap timer is the same as that in the data plan. l Run the display digitmap command to check whether the digitmap is configured correctly.
Page 288 SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service Table 7-23 Software parameters of an MG interface that supports H.248 Parameter Description Default Setting Indicates whether the MG Numeral type. Range: 0-2. interface supports dual homing. l 0: Indicates that dual homing To configure an MG interface is not supported.
Page 289 SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service Parameter Description Default Setting Indicates whether a wildcard is Numeral type. Range: 0-1. used for the registration of the l 0: Indicates that a wildcard is MG interface.
Page 290 SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service Parameter Description Default Setting Indicates whether the MG Numeral type. Range: 0-1. interface supports security l 0: Indicates that security header. header is supported. To configure an MG interface...
Page 291 SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service Parameter Description Default Setting Indicates the maximum Numeral type. Range: 0-1. digitmap matching flag of the l 0: Indicates that the match MG interface. follows the protocol. To configure digitmap...
Page 292 SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service Parameter Description Default Setting Indicates the length of the timer Numeral type. Range: 0-30s. for filtering the media stream Default: 5s source port of the MG interface. To configure the length of the...
Page 293 SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service Parameter Description Default Setting Indicates the type of remote Numeral type. Range: 0-4. blocking play tone. l 0: Indicates the busy tone. l 1: Indicates the device congestion tone.
Page 294 SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service Parameter Description Default Setting Indicates whether the MG Numeral type. Range: 0-1. actively establishes or releases l 0: Yes the link for the BRA user after l 1: No the MGC initiates the in-service or OOS request.
Page 295: Optional) Configuring The Ringing Mode Of An Mg Interface
SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service Example To configure software parameter 11 of H.248-based MG interface 0 to 1 so that the MG interface supports emergency standalone and allows only internal calls, do as follows:...
Page 296 0 (the values of the corresponding parameters cadence and initialring are 128 and 144 respectively). To configure the ringing mode of MG interface 0, do as follows: huawei(config)#user defined-ring modify 0 para1 400 para2 200 para3 400 para4 2000 huawei(config)#display user defined-ring --------------------------------------------------...
Page 297: Optional) Configuring The Tid Format Of An Mg Interface
SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service Command: display mg-ringmode attribute ------------------------------------------------------- MGID PeerPara CadenceRing InitialRing ------------------------------------------------------- ------------------------------------------------------- 7.3.1.7 (Optional) Configuring the TID Format of an MG Interface The TID format determines how various user terminal IDs on the MG interface are generated.
Page 298 SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service template that is bound to the type of users. Then, run the display tid-template command to check whether the TID template supports the layering configuration. Hence, you can check whether the user supports terminal layering.
Page 299: Enabling An Mg Interface
TID template 3 is used. To add a PSTN user on port 0/2/0 and check whether the system automatically allocates a TID generated according to the template, do as follows: huawei(config)#display tid-template 3// Query the information about the TID template 3.
Page 300: Configuring The Iua Link
SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service l Run the display if-h248 state command to check whether the MG interface is in the normal state. l Run the quit command to quit the global config mode, and then run the display if-h248 all command to check whether the MG interface is in the normal state.
Page 301: Adding An Iua Link
20s, prefix of the IID is b/, IID generation mode is using the binary value that is automatically generated in ffsspp mode, namely, parameter 2. To add such an IUA link set, do as follows: huawei(config)#sigtran huawei(config-sigtran)#iua-linkset add 0 trafficmode override pendingtime 20 iid- map 2 braprefix b/ huawei(config-sigtran)#display iua-linkset attribute { <cr>|linksetno<L>...
Page 302: Configuring The Voip Isdn Bra User
Assume that the link ID is 0, link set ID is 0, local port ID is 1402, local IP address is 10.10.10.10, remote port ID is 1404, and remote IP address 1 is 10.10.10.20. To add such a link, do as follows: huawei(config)#sigtran huawei(config-sigtran)#iua-link add 0 0 1402 10.10.10.10 1404 10.10.10.20 huawei(config-sigtran)#display iua-link attribute { <cr>|linkno<L> }:...
Page 303 SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service Default Configuration Table 7-24 lists the default settings of the attributes of the ISDN BRA user. When configuring these attributes, you can modify the values according to the service requirements.
Page 304: Optional) Configuring The System Parameters
To add an ISDN BRA user with such configurations on port 0/4/0 of MG interface 0, do as follows: huawei(config-sigtran)#quit huawei(config)#esl user huawei(config-esl-user)#mgbrauser add 0/4/0 0 0 interfaceid 0 terminalid 2 prior ity cat3 telno 83110001 Are you sure to configure the working mode of the DSL board to normal and reset the board automatically? (y/n)
Page 305: Optional) Configuring The Overseas Parameters
SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service Parameter Description Default Setting Indicates the initial ringing stop 0: Indicates that the initial flag. ringing stop flag is not issued. Indicates the MWI mode. 1: Indicates that the FSK is sent with ringing.
Page 306: Optional) Configuring The Attributes Of An Isdn Bra Port
SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service Table 7-26 Overseas parameters supported by the MA5616 Parameter Description Default Setting Indicates the upper threshold of 350 ms (in compliance with the the flash-hooking duration. Chinese mainland standards)
Page 307 Assume that the working mode is p2mp, the activation mode is stable, and the auto-deactivation function is disabled. To configure such attributes of ISDN BRA port 0/4/0, do as follows: huawei(config)#braport huawei(config-braport)#braport attribute set 0/4/0 workmode p2mp activemode stable- active huawei(config-braport)#display braport attribute { frameid/slotid/portid<S><Length 1-15>|frameid/slotid<S><Length 1-15>...
Page 308: Configuring The Foip Service (Based On The H.248 Protocol)
SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service 7.4 Configuring the FoIP Service (Based on the H.248 Protocol) This topic describes how to configure the FoIP service when the H.248 protocol is used to transmit the fax data service over the IP network.
Page 309 SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service RFC 2198 function: Through the redundant transmission, the RFC 2198 function improves the reliability of data transmission. When the network packet loss occurs, the RFC 2198 can ensure the service quality.
Page 310: Configuring The Foip Service (Based On The Sip Protocol)
SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service NOTE If the fax machines are not configured on the same MG interface, the configurations for whether the T.38 fax port ID is added by 2 for the two sides must be consistent. That is, the T.38 fax port ID of the two sides are both added by 2 or not added by 2.
Page 311 SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service Context During the application of the fax service, the FoIP service can be classified into two modes according to the participation of the SIP signaling in the transmission control process: Self-switch: If the self-switch mode is configured, the fax working mode of the MA5616 needs to be configured manually.
Page 312 SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service Table 7-30 Default configuration of the flows of the FoIP service Item Default Codec negotiation mode Negotiation Codec mode Transparent transmission fax Procedure Step 1 Configure public fax and modem parameters.
Page 313: Configuring The Moip Service (Based On The H.248 Protocol)
SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service MGID Nego-mode :self-switch Rtp-interval :10ms Vbd-codec :G.711A Vbd-pt-type :static Vbd-attribute-type :v.152 ------------------------------------------------------------------------------- huawei(config-if-sip-0)#fax parameters transmode 0 huawei(config-if-sip-0)#quit huawei(config)#display fax parameters { <cr>|mgid<U><0,16777215> }:0 Command: display fax parameters 0...
Page 314 SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service The report mode of the modem event: Direct: In direct mode, the host reports the modem event to the MGC immediately when the host receives a modem event.
Page 315: Configuring The Moip Service (Based On The Sip Protocol)
SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service The 10 ms packing function and the RFC2198 intelligent startup function are enabled. The transmission mode of the modem event is ControlledByMGC (default). The codec mode of the VBD is G.711A (default).
Page 316 SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service This reduces delay, improves the performance of transparent transmission, and decreases the impact of packet loss on the transmission of the modem service data. RFC 2198 function: Through the redundant transmission, the RFC 2198 improves the reliability of data transmission.
Page 317: Configuring The Security And Reliability Of The Voice Service
MG ID, must be configured on the MGC. These parameters must be the same as the parameters configured on the MA5616. Precautions When the MGC is Huawei SoftX3000, the authentication MG ID must be a string of more than eight characters. Issue 04 (2011-10-30) Huawei Proprietary and Confidential Copyright ©...
Page 318 SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service Procedure Step 1 In global config mode, run the interface h248 command to enter the MG interface mode. Step 2 Run the mg-software parameter 4 command to configure the registration mode.
Page 319: Configuring The Device Authentication (Based On The Sip Protocol)
SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service ------------------------------------------------- APPENDIX: ------------------------------------------------- Interface software parameter name: 6: Whether MG supports authentication 0: Yes 1: No huawei(config-if-h248-0)#auth auth_mgid MA5616 initial_key 0123456789ABCDEF huawei(config-if-h248-0)#display auth [AUTH_PARA config] Initial Key : 0123456789ABCDEF...
Page 320: Configuring The Dual Homing
----End Example To configure the authentication information for SIP interface 0 with the user name of huawei.com and the password of 123456789, do as follows: huawi(config)#interface sip 0 huawei(config-if-sip-0)#sip-auth-parameter { <cr>|auth-mode<K>|password-mode<K> }:password-mode { password-mode-value<E><password,ha1> }:password { <cr>|auth-mode<K>...
Page 321: Configuring The Dual Homing (Based On The Sip Protocol)
SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service Procedure Step 1 In global config mode, run the interface h248 command to enter the MG interface mode. Step 2 Run the mg-software parameter 2 command to configure the MG interface to support the dual homing.
Page 322 5060 primary-proxy-domain proxy.domain secondary-proxy-ip1 10.10.10.15 secondary-proxy-port 5060 huawei(config-if-sip-0)#if-sip attribute basic home-domain huawei.com sipprofile- index 1 { <cr>|media-ip<K>|primary-proxy-domain<K>|primary-proxy-ip1<K>|primary-proxy-ip 2<K>|primary-proxy-port<K>|proxy-addr-mode<K>|secondary-proxy-domain<K>|secondar y-proxy-ip1<K>|secondary-proxy-ip2<K>|secondary-proxy-port<K>|server-dhcp-option <K>|signal-ip<K>|signal-port<K>|srvlogic-index<K>|transfer<K> }: Command: if-sip attribute basic home-domain huawei.com sipprofile-index 1 huawei(config-if-sip-0)#reset Issue 04 (2011-10-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
Page 323: Configuring The Emergency Standalone
SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service Related Operation Table 7-33 lists the related operation for configuring the dual homing. Table 7-33 Related operation for configuring the dual homing To... Run the Command... Query the configuration of the SIP...
Page 324 SmartAX MA5616 Multi-service Access Module Configuration Guide 7 Configuring the Voice Service NOTE In general, the default parameters of the emergency standalone timers are used, and you need not configure them. ----End Example To configure MG0 to support the emergency standalone function and configure the digitmap...
Page 325: Configuration Example Of Services On The Ma5616 Through Gpon Upstream Transmission
SmartAX MA5616 Multi-service Access Module 8 Configuration Example of Services on the MA5616 Configuration Guide Through GPON Upstream Transmission Configuration Example of Services on the MA5616 Through GPON Upstream Transmission About This Chapter This topic describes how to configure Internet access service, multicast service, voice service, and triple play service on the MA5616 on different networks.
Page 326: Configuration Example Of The Xdsl Internet Access Service
SmartAX MA5616 Multi-service Access Module 8 Configuration Example of Services on the MA5616 Configuration Guide Through GPON Upstream Transmission 8.1 Configuration Example of the xDSL Internet Access Service This topic describes how to configure the xDSL Internet access service in the PPPoE, IPoE, PPPoA and IPoA modes.
Page 327 SmartAX MA5616 Multi-service Access Module 8 Configuration Example of Services on the MA5616 Configuration Guide Through GPON Upstream Transmission MA5616 in the upstream direction. For the identification purpose, the user name and password for dial-up Internet access must be configured on the BRAS.
Page 328 VPI and VCI of the modem are 1 and 39, and the access port ID is 0/2/0. To facilitate the maintenance of the service port, also configure the service port description. huawei(config)#service-port 1 vlan 50 adsl 0/2/0 vpi 1 vci 39 inbound traffic- table index 5 outbound traffic-table index 5 huawei(config)#service-port desc 1 description Vlanid:50/adsl/vpi:1vci:39/ stacking Set the C-VLAN ID of the preset service port 1 to 10 for identifying the user.
Page 329 S-VLAN ID to 50. Set the SHDSL channel mode to PTM, and create service port 2 on SHDSL port 0/4/0. To facilitate the maintenance of the service port, also configure the service port description. huawei(config)#service-port 2 vlan 50 shdsl mode ptm 0/4/0 inbound traffic- table index 5 outbound traffic-table index 5 huawei(config)#service-port desc 2 description Vlanid:50/shdsl/vpi:1vci:39/ stacking Set the C-VLAN ID of the preset service port 2 to 10 for identifying the user.
Page 330 2 ms, SNR margin is 6 dB, minimum downstream INP is 4, and minimum upstream INP is 2. huawei(config)#vdsl line-profile quickadd 3 snr 60 0 300 60 0 300 huawei(config)#vdsl channel-profile quickadd 3 path-mode ptm interleaved-delay...
Page 331 S-VLAN ID to 50. Set the VDSL channel mode to PTM, and create service port 3 on VDSL port 0/1/0. To facilitate the maintenance of the service port, also configure the service port description. huawei(config)#service-port 3 vlan 50 vdsl mode ptm 0/1/0 inbound traffic- table index 5 outbound traffic-table index 5...
Page 332 SmartAX MA5616 Multi-service Access Module 8 Configuration Example of Services on the MA5616 Configuration Guide Through GPON Upstream Transmission vlan 50 smart vlan attrib 50 stacking vlan service-profile profile-id 1 forwarding vlan-connect commit quit vlan bind service-profile 50 profile-id 1...
Page 333: Configuration Example Of The Xdsl Ipoe Internet Access Service
SmartAX MA5616 Multi-service Access Module 8 Configuration Example of Services on the MA5616 Configuration Guide Through GPON Upstream Transmission 8.1.2 Configuration Example of the xDSL IPoE Internet Access Service This topic describes how to configure a user so that the user can access the MA5616 in the xDSL mode, and then access the Internet in the IPoE mode at a rate of 2048 kbit/s.
Page 334 SmartAX MA5616 Multi-service Access Module 8 Configuration Example of Services on the MA5616 Configuration Guide Through GPON Upstream Transmission huawei(config)#port vlan 50 0/0 0 Step 3 In the ADSL access mode, follow this procedure. Configure an ADSL2+ profile. For details, see 3.7.1 Configuring the ADSL2+...
Page 335 VPI and VCI of the modem are 1 and 39, and the access port ID is 0/2/0. To facilitate the maintenance of the service port, also configure the service port description. huawei(config)#service-port 1 vlan 50 adsl 0/2/0 vpi 1 vci 39 inbound traffic- table index 5 outbound traffic-table index 5 huawei(config)#service-port desc 1 description Vlanid:50/adsl/vpi:1vci:39/ stacking Set the C-VLAN ID of the preset service port 1 to 10 for identifying the user.
Page 336 2 ms, SNR margin is 6 dB, minimum downstream INP is 4, and minimum upstream INP is 2. huawei(config)#vdsl line-profile quickadd 3 snr 60 0 300 60 0 300 huawei(config)#vdsl channel-profile quickadd 3 path-mode ptm interleaved-delay...
Page 337 S-VLAN ID to 50. Set the VDSL channel mode to PTM, and create service port 3 on VDSL port 0/1/0. To facilitate the maintenance of the service port, also configure the service port description. huawei(config)#service-port 3 vlan 50 vdsl mode ptm 0/1/0 inbound traffic- table index 5 outbound traffic-table index 5...
Page 338 SmartAX MA5616 Multi-service Access Module 8 Configuration Example of Services on the MA5616 Configuration Guide Through GPON Upstream Transmission Step 6 Configure the security of user accounts. Assume that the RAIO mode is the user-defined mode, the CID is the access node name frame/ slot/port:vlanid, the RID is the label of the service port where the user is connected.
Page 339: Configuration Example Of The Xdsl Pppoa Internet Access Service
SmartAX MA5616 Multi-service Access Module 8 Configuration Example of Services on the MA5616 Configuration Guide Through GPON Upstream Transmission interface shl 0/4 activate 0 3 alarm-config 0 1 quit service-port 2 vlan 50 shdsl mode ptm 0/4/0 inbound traffic-table index 5 outbound...
Page 340 The ID of the ADSL2+ line profile is 3, the downstream rate is 2048 kbit/s, the channel mode is the interleave mode, the maximum interleave delay is 10 ms, and the SNR margin is 6 dB. huawei(config)#adsl line-profile quickadd 3 snr 60 30 120 60 30 120 huawei(config)#adsl channel-profile quickadd 3 interleaved-delay 10 10 rate 1024...
Page 341 Assume that the management VPI and VCI of the modem are 1 and 39. To facilitate the maintenance of the service port, also configure the service port description. huawei(config)#service-port 1 vlan 50 adsl 0/2/0 vpi 1 vci 39 inbound traffic- table index 5 outbound traffic-table index 5 huawei(config)#service-port desc 1 description MA5616HW/Vlanid:50/adsl/smart Set the maximum number of MAC addresses that can be learned by the service port is 16.
Page 342 ID of the SHDSL line profile is 3, the line rate is 2048 kbit/s, and the profile is used to activate 4-wire ports. huawei(config)#shdsl line-profile quickadd 3 line four-wire rate 2048 Activate the SHDSL port. The port is port 0/4/0, and SHDSL line profile 3 and the default alarm profile (alarm profile 1) are bound to the port.
Page 343 VCI of the peer modem. Assume that the management VPI and VCI of the modem are 1 and 39. To facilitate the maintenance of the service port, also configure the service port description. huawei(config)#service-port 2 vlan 50 shdsl mode atm 0/4/0 vpi 1 vci 39 inbound traffic-table index 5 outbound traffic-table index 5 huawei(config)#service-port desc 2 description MA5616HW/Vlanid:50/shdsl/smart Set the maximum number of MAC addresses that can be learned by the service port is 16.
Page 344 VCI of the peer modem. Assume that the management VPI and VCI of the modem are 1 and 39. To facilitate the maintenance of the service port, also configure the service port description. huawei(config)#service-port 3 vlan 50 vdsl mode atm 0/1/0 vpi 1 vci 39 inbound traffic-table index 5 outbound...
Page 345 SmartAX MA5616 Multi-service Access Module 8 Configuration Example of Services on the MA5616 Configuration Guide Through GPON Upstream Transmission NOTE For details about the PITP configuration for the user account security, see 3.10.1 Configuring Anti-Theft and Roaming of User Account Through PITP.
Page 346: Configuration Example Of The Xdsl Ipoa Internet Access Service
SmartAX MA5616 Multi-service Access Module 8 Configuration Example of Services on the MA5616 Configuration Guide Through GPON Upstream Transmission encapsulation 0/4/0 vpi 1 vci 39 type pppoa llc pitp enable pmode raio-mode cntel pitp-pmode save Configuration File for the VDSL access mode:...
Page 347 The ID of the ADSL2+ line profile is 3, the downstream rate is 2048 kbit/s, the channel mode is the interleave mode, the maximum interleave delay is 10 ms, and the SNR margin is 6 dB. huawei(config)#adsl line-profile quickadd 3 snr 60 30 120 60 30 120 huawei(config)#adsl channel-profile quickadd 3 interleaved-delay 10 10 rate 1024...
Page 348 Assume that the management VPI and VCI of the modem are 1 and 39. To facilitate the maintenance of the service port, also configure the service port description. huawei(config)#service-port 1 vlan 50 adsl 0/2/0 vpi 1 vci 39 inbound traffic- table index 5 outbound traffic-table index 5 huawei(config)#service-port desc 1 description MA5616HW/Vlanid:50/adsl/smart Set the maximum number of MAC addresses that can be learned by the service port is 16.
Page 349 VCI of the peer modem. Assume that the management VPI and VCI of the modem are 1 and 39. To facilitate the maintenance of the service port, also configure the service port description. huawei(config)#service-port 2 vlan 50 shdsl mode atm 0/4/0 vpi 1 vci 39 inbound traffic-table index 5 outbound traffic-table index 5 huawei(config)#service-port desc 2 description MA5616HW/Vlanid:50/shdsl/smart Set the maximum number of MAC addresses that can be learned by the service port is 16.
Page 350 2 ms, SNR margin is 6 dB, minimum downstream INP is 4, and minimum upstream INP is 2. huawei(config)#vdsl line-profile quickadd 3 snr 60 0 300 60 0 300 huawei(config)#vdsl channel-profile quickadd 3 path-mode atm interleaved-delay...
Page 351 VCI of the peer modem. Assume that the management VPI and VCI of the modem are 1 and 39. To facilitate the maintenance of the service port, also configure the service port description. huawei(config)#service-port 3 vlan 50 vdsl mode atm 0/1/0 vpi 1 vci 39 inbound traffic-table index 5 outbound...
Page 352: Configuration Example Of The Multicast Service (Multicast Vlan Mode)
SmartAX MA5616 Multi-service Access Module 8 Configuration Example of Services on the MA5616 Configuration Guide Through GPON Upstream Transmission 2048 3096 adsl line-template quickadd 3 line 3 channel1 3 60 70 channel2 3 interface adsl 0/2 deactivate 0 activate 0 template-index 3...
Page 353: Configuration Example Of The Multicast Video Service (Static Configuration Mode)
SmartAX MA5616 Multi-service Access Module 8 Configuration Example of Services on the MA5616 Configuration Guide Through GPON Upstream Transmission 8.2.1 Configuration Example of the Multicast Video Service (Static Configuration Mode) This topic describes how to configure the multicast video service if the program in the multicast VLAN is configured statically.
Page 354 SmartAX MA5616 Multi-service Access Module 8 Configuration Example of Services on the MA5616 Configuration Guide Through GPON Upstream Transmission Figure 8-5 Example network of the multicast service Multicast Source ISP2 ISP1 Router MA5616 Home Gateway user1 user2 Data Plan Table 8-1 provides the data plan for configuring the multicast service.
Page 355 Step 1 Create VLANs and add an uplink port to the VLANs. huawei(config)#vlan 4002-4003 smart huawei(config)#port vlan 4002-4003 0/0 1 Step 2 Configure service ports. huawei(config)#service-port 100 vlan 4002 vdsl mode ptm 0/1/0 multi-service user- vlan untagged rx-cttr 6 tx-cttr 6 huawei(config)#service-port 101 vlan 4003 vdsl mode ptm 0/1/1 multi-service user-...
Page 356 If the IGMP version of the multicast VLAN is V3, the source IP address of the program in the multicast VLAN must be configured. If the IGMP version of the multicast VLAN is V2, the source IP address of the program in the multicast VLAN cannot be configured. huawei(config-mvlan4002)#igmp program add name program1 ip 224.1.1.1 sourceip 10.10.10.10 huawei(config-mvlan4002)#multicast-vlan 4003 huawei(config-mvlan4003)#igmp program add name program2 ip 224.1.1.2 sourceip...
Page 357: Configuration Example Of The Multicast Video Service (Dynamic Generation Mode)
SmartAX MA5616 Multi-service Access Module 8 Configuration Example of Services on the MA5616 Configuration Guide Through GPON Upstream Transmission multicast-vlan 4002 igmp mode proxy multicast-vlan 4003 igmp mode proxy Configure the multicast uplink port, multicast programs, and multicast users. igmp uplink-port 0/0/1...
Page 358 SmartAX MA5616 Multi-service Access Module 8 Configuration Example of Services on the MA5616 Configuration Guide Through GPON Upstream Transmission Figure 8-6 Example network of the multicast service Multicast Source ISP2 ISP1 Router MA5616 Home Gateway user1 user2 Data Plan Table 8-2 provides the data plan for configuring the multicast service.
Page 359 Step 1 Create VLANs and add an uplink port to the VLANs. huawei(config)#vlan 4002-4005 smart huawei(config)#port vlan 4002-4005 0/0 1 Step 2 Configure service ports. huawei(config)#service-port 100 vlan 4004 vdsl mode ptm 0/1/0 multi-service user- vlan untagged rx-cttr 6 tx-cttr 6 huawei(config)#service-port 101 vlan 4005 vdsl mode ptm 0/1/1 multi-service user-...
Page 360 Therefore, plan the multicast program mode before configuring the multicast program. This command can be executed only when the IGMP function is disabled. huawei(config-mvlan4002)#igmp match group ip 224.1.1.1 to-ip 224.1.1.2 huawei(config-mvlan4002)#multicast-vlan 4003 huawei(config-mvlan4003)#igmp match group ip 224.1.1.1 to-ip 224.1.1.2 Step 6 Configure multicast users.
Page 361: Configuration Example Of The Voip Service
SmartAX MA5616 Multi-service Access Module 8 Configuration Example of Services on the MA5616 Configuration Guide Through GPON Upstream Transmission multicast-vlan 4002 igmp match mode disable igmp mode proxy multicast-vlan 4003 igmp match mode disable igmp mode proxy Configure the multicast uplink port, multicast programs, and multicast users.
Page 362 SmartAX MA5616 Multi-service Access Module 8 Configuration Example of Services on the MA5616 Configuration Guide Through GPON Upstream Transmission Figure 8-7 Example network of the VoIP service based on the H.248 protocol Data Plan After the service requirements are further confirmed and analyzed with engineers of the office,...
Page 363 SmartAX MA5616 Multi-service Access Module 8 Configuration Example of Services on the MA5616 Configuration Guide Through GPON Upstream Transmission Item Data configuration Media and 0/0/1 on the MGC.) signaling upstream port Media IP address These two IP addresses are both and signaling IP 10.10.10.10.
Page 364 SmartAX MA5616 Multi-service Access Module 8 Configuration Example of Services on the MA5616 Configuration Guide Through GPON Upstream Transmission Item Data Software Parameters of an According to the Context in Software MG Interface Parameters of an MG Interface confirmed with the engineers of the office, the default configuration can meet the service requirements.
Page 365 SmartAX MA5616 Multi-service Access Module 8 Configuration Example of Services on the MA5616 Configuration Guide Through GPON Upstream Transmission Item Data User priority Users are common users, and the user priority uses the default priority, namely, cat3. User type Users are common users, and the user type uses the default user type, namely, DEL.
Page 366 Step 5 Configure the TID template of the PSTN user on MG interface 0. Configure the TID generation mode. According to the data plan, the terminal prefix of the PSTN user needs to be configured to huawei, and the TID template adopts layering template 6. Issue 04 (2011-10-30) Huawei Proprietary and Confidential Copyright ©...
Page 367 SmartAX MA5616 Multi-service Access Module 8 Configuration Example of Services on the MA5616 Configuration Guide Through GPON Upstream Transmission CAUTION The MA5616 requires that the terminal prefixes of PSTN users, ISDN BRA users, and ISDN PRA users on the same H.248 interface are either the same or different. Note this when configuring the terminal prefix.
Page 368 If the MGC is configured with the call forwarding service, cancel the call forwarding service on the MGC. l If the MGC is not configured with the call forwarding service, contact Huawei technical support engineer to handle the fault.
Page 369: Configuration Example Of The Voip Pstn Service (Based On The Sip Protocol)
SmartAX MA5616 Multi-service Access Module 8 Configuration Example of Services on the MA5616 Configuration Guide Through GPON Upstream Transmission Query the running status of the MG interface. quit display if-h248 all Configure the PSTN user data. esl user mgpstnuser batadd 0/3/0 0/3/31 0 Configure the local digitmap.
Page 370 SmartAX MA5616 Multi-service Access Module 8 Configuration Example of Services on the MA5616 Configuration Guide Through GPON Upstream Transmission Figure 8-8 Example network of the VoIP PSTN service based on the SIP protocol Data Plan Run the display system parameters and display oversea parameters commands to query the system parameters and overseas parameters.
Page 371 Configure the data of the PSTN users (phone 0-phone 31) in slot 0/3. huawei(config)#esl user huawei(config-esl-user)#sippstnuser batadd 0/3/0 0/3/31 0 telno 83110000 Configure the priority of the PSTN user in slot 0/3/0 to Cat2. huawei(config-esl-user)#sippstnuser attribute set 0/3/0 priority cat2 Configure the type of the PSTN user in slot 0/3.
Page 372: Configuration Example Of The Voip Isdn Bra Service
If the IMS is configured with the call forwarding service, cancel the call forwarding service on the IMS. l If the IMS is not configured with the call forwarding service, contact Huawei technical support engineer to handle the fault.
Page 373 SmartAX MA5616 Multi-service Access Module 8 Configuration Example of Services on the MA5616 Configuration Guide Through GPON Upstream Transmission board, implementing the ISDN BRA service. The ISDN BRA service on the MA5616 can be supported only by the H.248 protocol.
Page 374 SmartAX MA5616 Multi-service Access Module 8 Configuration Example of Services on the MA5616 Configuration Guide Through GPON Upstream Transmission Figure 8-9 Example network for configuring the ISDN BRA service Data Plan Table 8-5 provides the data plan for configuring the ISDN BRA service.
Page 375 SmartAX MA5616 Multi-service Access Module 8 Configuration Example of Services on the MA5616 Configuration Guide Through GPON Upstream Transmission Item Data Default media gateway of 10.13.1.1 the MG interface TID profile ID of the TID profile used 2 (default, no configuration is required)
Page 376 SmartAX MA5616 Multi-service Access Module 8 Configuration Example of Services on the MA5616 Configuration Guide Through GPON Upstream Transmission Item Data Local port ID 1401 Local IP address 10.13.4.116/16 Remote port ID 1400 IP address of the primary 10.14.1.2/16 (IP address of the primary MGC)
Page 377 Step 11 Add an ISDN BRA user and configure the data. huawei(config-sigtran)#quit huawei(config)#esl user huawei(config-esl-user)#mgbrauser add 0/4/0 0 0 interfaceid 0 terminalid 2 priority cat3 telno 83110001 Are you sure to configure the working mode of the DSL board to normal and reset...
Page 378 SmartAX MA5616 Multi-service Access Module 8 Configuration Example of Services on the MA5616 Configuration Guide Through GPON Upstream Transmission When ISDN phone3 dials number 83110001, ISDN phone1 and ISDN phone2 can hear the ringing tone at the same time. In addition, ISDN phone1 and ISDN phone2 can communicate with ISDN phone3 at the same time.
Page 379: Configuration Example Of The Vlan Stacking Wholesale Service
SmartAX MA5616 Multi-service Access Module 8 Configuration Example of Services on the MA5616 Configuration Guide Through GPON Upstream Transmission mgbrauser add 0/4/0 0 0 interfaceid 0 terminalid 2 priority cat3 telno 83110001 mgbrauser add 0/4/1 0 0 interfaceid 2 terminalid 4 priority cat1 telno 83110002 Save the data.
Page 380 SmartAX MA5616 Multi-service Access Module 8 Configuration Example of Services on the MA5616 Configuration Guide Through GPON Upstream Transmission Figure 8-10 Example network for configuring the VLAN stacking wholesale service VLAN ID:101 VLAN ID:100 ISP2 ISP1 LAN Switch BRAS BRAS...
Page 381 VLAN stacking on the MA5616. You can also run the stacking inner-ethertype command to set the type of inner Ethernet protocol supported by VLAN stacking on the MA5616. To ensure that Huawei device is interconnected with the device of other vendors, the type of the inner/outer Ethernet protocol must be the same as that of the interconnect device.
Page 382 Step 4 Add service ports to VLANs. Create service ports for users 1, 2, 3, and 4, and then add the service ports to VLAN 100 and VLAN 101. huawei(config)#service-port 1 vlan 100 vdsl mode ptm 0/1/0 multi-service user-encap pppoe rx-cttr 6 tx-cttr 6...
Page 383: Configuration Example Of The Vlan Id Extension Service
SmartAX MA5616 Multi-service Access Module 8 Configuration Example of Services on the MA5616 Configuration Guide Through GPON Upstream Transmission Configuration File The following describes the configuration file of this configuration example. Note that certain steps must be performed manually and the configuration file cannot be imported directly.
Page 384 SmartAX MA5616 Multi-service Access Module 8 Configuration Example of Services on the MA5616 Configuration Guide Through GPON Upstream Transmission Service Requirements The Internet access service is deployed on the network. Two VLAN IDs are allocated on the BRAS to identify four access users.
Page 385 Add an uplink port to the VLAN. huawei(config)#port vlan 100 0/0 1 Add service ports to the VLAN. huawei(config)#service-port vlan 100 vdsl mode ptm 0/1/2 multi-service user-encap pppoe rx-cttr 6 tx-cttr 6 huawei(config)#service-port vlan 100 vdsl mode ptm 0/1/3 multi-service...
Page 386 SmartAX MA5616 Multi-service Access Module 8 Configuration Example of Services on the MA5616 Configuration Guide Through GPON Upstream Transmission INDEX VLAN VLAN PORT F/ S/ P VPI FLOW FLOW STATE ATTR TYPE TYPE PARA ------------------------------------------------------------------------- 100 common 0/1 /2 encap pppoe...
Page 387: Configuring The Triple Play Service
SmartAX MA5616 Multi-service Access Module 8 Configuration Example of Services on the MA5616 Configuration Guide Through GPON Upstream Transmission tx-cttr 6 Set the inner VLAN tag. stacking label service-port 0 11 stacking label service-port 1 12 Configuration file of MA5616_B Create a VLAN.
Page 388 SmartAX MA5616 Multi-service Access Module 8 Configuration Example of Services on the MA5616 Configuration Guide Through GPON Upstream Transmission Service Requirements The MA5616 is used on the GPON upstream transmission network. VDSL2 user 1 and VDSL2 user 2 are connected to the MA5616 to implement the triple play.
Page 389 SmartAX MA5616 Multi-service Access Module 8 Configuration Example of Services on the MA5616 Configuration Guide Through GPON Upstream Transmission Table 8-8 Data plan of the triple play service based on the user-side VLAN Item Data VDSE Service ports: 0/1/0 and 0/1/1...
Page 390 SmartAX MA5616 Multi-service Access Module 8 Configuration Example of Services on the MA5616 Configuration Guide Through GPON Upstream Transmission Item Data Upstream The 802.1p priorities are used. The VoIP service has priority 6, IPTV service priority priority 5, and Internet service priority 1.
Page 391 Add service ports to the VLAN. Add service ports to the VLAN and use the traffic profile configured in the preceding step. huawei(config)#service-port vlan 102 vdsl mode atm 0/1/0 vpi 0 vci 35 multi-serv ice user-vlan 2 rx-cttr 7 tx-cttr 7...
Page 392 Add service ports to the VLAN. Add service ports to the VLAN and use the traffic profile configured in the preceding step. huawei(config)#service-port 10 vlan 105 vdsl mode atm 0/1/0 vpi 0 vci 35 multi-serv ice user-vlan 4 rx-cttr 9 tx-cttr 9...
Page 393 SmartAX MA5616 Multi-service Access Module 8 Configuration Example of Services on the MA5616 Configuration Guide Through GPON Upstream Transmission Configure multicast users. huawei(config-btv)#igmp user add service-port 10 huawei(config-btv)#igmp user add service-port 11 auth huawei(config-btv)#igmp user bind-profile service-port 11 profile- name profile0...
Page 394: Configuring The Triple Play Service - Single Pvc For Multiple Services Based On The User-Side 802.1P
SmartAX MA5616 Multi-service Access Module 8 Configuration Example of Services on the MA5616 Configuration Guide Through GPON Upstream Transmission igmp uplink-port 0/0/1 igmp uplink-port-mode default multicast-vlan 104 igmp program add name program1 ip 224.1.1.1 sourceip 10.10.10.10 igmp program add name program2 ip 224.1.1.2 sourceip 10.10.10.11...
Page 395 SmartAX MA5616 Multi-service Access Module 8 Configuration Example of Services on the MA5616 Configuration Guide Through GPON Upstream Transmission Figure 8-14 Example network for configuring the triple play service in the single-PVC for multiple services mode based on the user-side 802.1p priority OSS &...
Page 396 SmartAX MA5616 Multi-service Access Module 8 Configuration Example of Services on the MA5616 Configuration Guide Through GPON Upstream Transmission Table 8-9 Data plan for configuring the triple play service in the single-PVC for multiple services mode based on the user-side 802.1p priority...
Page 397 SmartAX MA5616 Multi-service Access Module 8 Configuration Example of Services on the MA5616 Configuration Guide Through GPON Upstream Transmission Item Data Upstream The 802.1p priorities are used. The VoIP service has priority 6, IPTV service priority priority 5, and Internet service priority 1.
Page 398 Add service ports to the VLAN. Add service ports to the VLAN and use the traffic profile configured in the preceding step. huawei(config)#service-port vlan 102 vdsl mode atm 0/1/0 vpi 0 vci 35 multi-serv ice user-8021p 2 rx-cttr 7 tx-cttr 7...
Page 399 Add service ports to the VLAN. Add service ports to the VLAN and use the traffic profile configured in the preceding step. huawei(config)#service-port 10 vlan 105 vdsl mode atm 0/1/0 vpi 0 vci 35 multi-serv ice user-8021p 4 rx-cttr 9 tx-cttr 9...
Page 400 SmartAX MA5616 Multi-service Access Module 8 Configuration Example of Services on the MA5616 Configuration Guide Through GPON Upstream Transmission huawei(config)#btv huawei(config-btv)#igmp profile add profile-name profile0 huawei(config-btv)#igmp profile profile-name profile0 program-name program1 watc Configure multicast users. huawei(config-btv)#igmp user add service-port 10...
Page 401: Configuring The Triple Play Service - Multiple Pvcs For Multiple Services
SmartAX MA5616 Multi-service Access Module 8 Configuration Example of Services on the MA5616 Configuration Guide Through GPON Upstream Transmission ice user-8021p 4 rx-cttr 9 tx-cttr 9 service-port 11 vlan 105 vdsl mode atm 0/1/1 vpi 0 vci 35 multi-serv ice user-8021p 4 rx-cttr 9 tx-cttr 9...
Page 402 SmartAX MA5616 Multi-service Access Module 8 Configuration Example of Services on the MA5616 Configuration Guide Through GPON Upstream Transmission Figure 8-16 Example network of the triple play service in the multi-PVC for multiple services mode OSS & RADIUS Server/ Multicase Sever...
Page 403 SmartAX MA5616 Multi-service Access Module 8 Configuration Example of Services on the MA5616 Configuration Guide Through GPON Upstream Transmission Item Data VPI/VCI for the Internet service: 0/37 VPI/VCI for the VoIP service: 0/36 VPI/VCI for the IPTV service: 0/35 Traffic...
Page 404 Add service ports to the VLAN and use the traffic profile configured in the preceding step. huawei(config)#service-port vlan 102 vdsl mode atm 0/1/0 vpi 0 vci 37 rx- cttr 7 tx-cttr 7 huawei(config)#service-port vlan 102 vdsl mode atm 0/1/1 vpi 0 vci 37 rx- cttr 7 tx-cttr 7 Save the data.
Page 405 Add service ports to the VLAN and use the traffic profile configured in the preceding step. huawei(config)#service-port vlan 103 vdsl mode atm 0/1/0 vpi 0 vci 36 rx- cttr 8 tx-cttr 8 huawei(config)#service-port vlan 103 vdsl mode atm 0/1/1 vpi 0 vci 36 rx- cttr 8 tx-cttr 8 Save the data.
Page 406 Are you sure to change the uplink port mode?(y/n)[n]:y Configure the program library. huawei(config-btv)#multicast-vlan 104 huawei(config-mvlan104)#igmp program add name program1 ip 224.1.1.1 sourceip 10. 10.10.10 huawei(config-mvlan104)#igmp program add name program2 ip 224.1.1.2 sourceip 10. 10.10.11 Configure the right profile.
Page 407 SmartAX MA5616 Multi-service Access Module 8 Configuration Example of Services on the MA5616 Configuration Guide Through GPON Upstream Transmission The IPTV user on port 0/1/0 can watch all the programs, and the IPTV user on port 0/1/1 can watch program 1 only.
Page 408: Configuration Example Of Services On The Ma5616 Through Ge Upstream Transmission
SmartAX MA5616 Multi-service Access Module 9 Configuration Example of Services on the MA5616 Configuration Guide Through GE Upstream Transmission Configuration Example of Services on the MA5616 Through GE Upstream Transmission About This Chapter This topic describes how to configure Internet access service, multicast service, voice service, and triple play service on the MA5616 on different networks.
Page 409: Configuration Example Of The Xdsl Internet Access Service
SmartAX MA5616 Multi-service Access Module 9 Configuration Example of Services on the MA5616 Configuration Guide Through GE Upstream Transmission 9.1 Configuration Example of the xDSL Internet Access Service This topic describes how to configure the xDSL Internet access service in the PPPoE, IPoE, PPPoA and IPoA modes.
Page 410 LACP static mode, do as follows: huawei(config)#link-aggregation 0/0 0 0/0 1 egress-ingress workmode lacp-static NOTE The aggregated ports must meet the following requirements: The ports must work in the full-duplex mode; the port rates must be the same and the rate of an electrical port must not be of the auto-negotiation type;...
Page 411 VPI and VCI of the modem are 1 and 39, and the access port ID is 0/2/0. To facilitate the maintenance of the service port, also configure the service port description. huawei(config)#service-port 1 vlan 50 adsl 0/2/0 vpi 1 vci 39 inbound traffic- table index 5 outbound traffic-table index 5 huawei(config)#service-port desc 1 description Vlanid:50/adsl/vpi:1vci:39/ stacking Set the C-VLAN ID of the preset service port 1 to 10 for identifying the user.
Page 412 S-VLAN ID to 50. Set the SHDSL channel mode to PTM, and create service port 2 on SHDSL port 0/4/0. To facilitate the maintenance of the service port, also configure the service port description. huawei(config)#service-port 2 vlan 50 shdsl mode ptm 0/4/0 inbound traffic- table index 5 outbound traffic-table index 5 Issue 04 (2011-10-30) Huawei Proprietary and Confidential Copyright ©...
Page 413 2 ms, SNR margin is 6 dB, minimum downstream INP is 4, and minimum upstream INP is 2. huawei(config)#vdsl line-profile quickadd 3 snr 60 0 300 60 0 300 huawei(config)#vdsl channel-profile quickadd 3 path-mode ptm interleaved-delay...
Page 414 S-VLAN ID to 50. Set the VDSL channel mode to PTM, and create service port 3 on VDSL port 0/1/0. To facilitate the maintenance of the service port, also configure the service port description. huawei(config)#service-port 3 vlan 50 vdsl mode ptm 0/1/0 inbound traffic- table index 5 outbound traffic-table index 5...
Page 415 SmartAX MA5616 Multi-service Access Module 9 Configuration Example of Services on the MA5616 Configuration Guide Through GE Upstream Transmission Step 4: When downloading files through FTP, you can open Task Manager in Windows and click Networking to check the link speed. Then, you can calculate the Internet access rate by the following formula: Attainable Internet access rate = Computer network adapter rate/48 x 53 x 8.
Page 416: Configuration Example Of The Xdsl Ipoe Internet Access Service
SmartAX MA5616 Multi-service Access Module 9 Configuration Example of Services on the MA5616 Configuration Guide Through GE Upstream Transmission interface vdsl 0/1 deactivate 0 activate 0 template-index 3 alarm-config 0 1 quit service-port 3 vlan 50 vdsl mode ptm 0/1/0 inbound traffic-table index 5 outbound...
Page 417 LACP static mode, do as follows: huawei(config)#link-aggregation 0/0 0 0/0 1 egress-ingress workmode lacp-static NOTE The aggregated ports must meet the following requirements: The ports must work in the full-duplex mode; the port rates must be the same and the rate of an electrical port must not be of the auto-negotiation type;...
Page 418 VPI and VCI of the modem are 1 and 39, and the access port ID is 0/2/0. To facilitate the maintenance of the service port, also configure the service port description. huawei(config)#service-port 1 vlan 50 adsl 0/2/0 vpi 1 vci 39 inbound traffic- table index 5 outbound traffic-table index 5 huawei(config)#service-port desc 1 description Vlanid:50/adsl/vpi:1vci:39/ stacking Set the C-VLAN ID of the preset service port 1 to 10 for identifying the user.
Page 419 S-VLAN ID to 50. Set the SHDSL channel mode to PTM, and create service port 2 on SHDSL port 0/4/0. To facilitate the maintenance of the service port, also configure the service port description. huawei(config)#service-port 2 vlan 50 shdsl mode ptm 0/4/0 inbound traffic- table index 5 outbound traffic-table index 5 huawei(config)#service-port desc 2 description Vlanid:50/shdsl/vpi:1vci:39/...
Page 420 2 ms, SNR margin is 6 dB, minimum downstream INP is 4, and minimum upstream INP is 2. huawei(config)#vdsl line-profile quickadd 3 snr 60 0 300 60 0 300 huawei(config)#vdsl channel-profile quickadd 3 path-mode ptm interleaved-delay...
Page 421 S-VLAN ID to 50. Set the VDSL channel mode to PTM, and create service port 3 on VDSL port 0/1/0. To facilitate the maintenance of the service port, also configure the service port description. huawei(config)#service-port 3 vlan 50 vdsl mode ptm 0/1/0 inbound traffic- table index 5 outbound traffic-table index 5...
Page 422 SmartAX MA5616 Multi-service Access Module 9 Configuration Example of Services on the MA5616 Configuration Guide Through GE Upstream Transmission Configuration File Configuration File for the ADSL access mode: vlan 50 smart vlan attrib 50 stacking vlan service-profile profile-id 1 forwarding vlan-connect...
Page 423: Configuration Example Of The Xdsl Pppoa Internet Access Service
SmartAX MA5616 Multi-service Access Module 9 Configuration Example of Services on the MA5616 Configuration Guide Through GE Upstream Transmission activate 0 template-index 3 alarm-config 0 1 quit service-port 3 vlan 50 vdsl mode ptm 0/1/0 inbound traffic-table index 5 outbound...
Page 424 The ID of the ADSL2+ line profile is 3, the downstream rate is 2048 kbit/s, the channel mode is the interleave mode, the maximum interleave delay is 10 ms, and the SNR margin is 6 dB. huawei(config)#adsl line-profile quickadd 3 snr 60 30 120 60 30 120 huawei(config)#adsl channel-profile quickadd 3 interleaved-delay 10 10 rate 1024...
Page 425 Assume that the management VPI and VCI of the modem are 1 and 39. To facilitate the maintenance of the service port, also configure the service port description. huawei(config)#service-port 1 vlan 50 adsl 0/2/0 vpi 1 vci 39 inbound traffic- table index 5 outbound traffic-table index 5 huawei(config)#service-port desc 1 description MA5616HW/Vlanid:50/adsl/smart Set the maximum number of MAC addresses that can be learned by the service port is 16.
Page 426 VCI of the peer modem. Assume that the management VPI and VCI of the modem are 1 and 39. To facilitate the maintenance of the service port, also configure the service port description. huawei(config)#service-port 2 vlan 50 shdsl mode atm 0/4/0 vpi 1 vci 39 inbound traffic-table index 5 outbound traffic-table index 5...
Page 427 2 ms, SNR margin is 6 dB, minimum downstream INP is 4, and minimum upstream INP is 2. huawei(config)#vdsl line-profile quickadd 3 snr 60 0 300 60 0 300 huawei(config)#vdsl channel-profile quickadd 3 path-mode atm interleaved-delay...
Page 428 VCI of the peer modem. Assume that the management VPI and VCI of the modem are 1 and 39. To facilitate the maintenance of the service port, also configure the service port description. huawei(config)#service-port 3 vlan 50 vdsl mode atm 0/1/0 vpi 1 vci 39 inbound traffic-table index 5 outbound...
Page 429 SmartAX MA5616 Multi-service Access Module 9 Configuration Example of Services on the MA5616 Configuration Guide Through GE Upstream Transmission Verification Step 1: Set the VPI/VCI of the modem to 1/39 and encapsulation mode to llc-pppoa. Configure the user name and password used for dialing (the user name and password must be the same as those configured on the BRAS.)
Page 430: Configuration Example Of The Xdsl Ipoa Internet Access Service
SmartAX MA5616 Multi-service Access Module 9 Configuration Example of Services on the MA5616 Configuration Guide Through GE Upstream Transmission vlan 50 smart port vlan 50 0/0 0 port vlan 50 0/0 1 link-aggregation 0/0 0 0/0 1 egress-ingress workmode lacp-static...
Page 431 The ID of the ADSL2+ line profile is 3, the downstream rate is 2048 kbit/s, the channel mode is the interleave mode, the maximum interleave delay is 10 ms, and the SNR margin is 6 dB. huawei(config)#adsl line-profile quickadd 3 snr 60 30 120 60 30 120 huawei(config)#adsl channel-profile quickadd 3 interleaved-delay 10 10 rate 1024...
Page 432 Assume that the management VPI and VCI of the modem are 1 and 39. To facilitate the maintenance of the service port, also configure the service port description. huawei(config)#service-port 1 vlan 50 adsl 0/2/0 vpi 1 vci 39 inbound traffic- table index 5 outbound traffic-table index 5 huawei(config)#service-port desc 1 description MA5616HW/Vlanid:50/adsl/smart Set the maximum number of MAC addresses that can be learned by the service port is 16.
Page 433 VCI of the peer modem. Assume that the management VPI and VCI of the modem are 1 and 39. To facilitate the maintenance of the service port, also configure the service port description. huawei(config)#service-port 2 vlan 50 shdsl mode atm 0/4/0 vpi 1 vci 39 inbound traffic-table index 5 outbound traffic-table index 5...
Page 434 2 ms, SNR margin is 6 dB, minimum downstream INP is 4, and minimum upstream INP is 2. huawei(config)#vdsl line-profile quickadd 3 snr 60 0 300 60 0 300 huawei(config)#vdsl channel-profile quickadd 3 path-mode atm interleaved-delay...
Page 435 VCI of the peer modem. Assume that the management VPI and VCI of the modem are 1 and 39. To facilitate the maintenance of the service port, also configure the service port description. huawei(config)#service-port 3 vlan 50 vdsl mode atm 0/1/0 vpi 1 vci 39 inbound traffic-table index 5 outbound...
Page 436 SmartAX MA5616 Multi-service Access Module 9 Configuration Example of Services on the MA5616 Configuration Guide Through GE Upstream Transmission formula: Attainable Internet access rate = Computer NIC rate/48 x 53 x 8. The calculated result approximates to the planned 2048 kbit/s.
Page 437: Configuration Example Of The Multicast Service (Multicast Vlan Mode)
SmartAX MA5616 Multi-service Access Module 9 Configuration Example of Services on the MA5616 Configuration Guide Through GE Upstream Transmission service-port desc 3 description MA5616HW/Vlanid:50/vdsl/smart mac-address max-mac-count service-port 3 16 mac-pool xpoa 0000-1111-1010 300 ipoa enable ipoa default gateway 192.168.1.20 encapsulation 0/1/0 vpi 1 vci 39 type ipoa llc srcIP 192.168.1.1 save 9.2 Configuration Example of the Multicast Service...
Page 438 SmartAX MA5616 Multi-service Access Module 9 Configuration Example of Services on the MA5616 Configuration Guide Through GE Upstream Transmission Figure 9-5 Example network of the multicast service Data Plan Table 9-1 provides the data plan for configuring the multicast service.
Page 439 Step 1 Create VLANs and add an uplink port to the VLANs. huawei(config)#vlan 4002-4005 smart huawei(config)#port vlan 4002-4005 0/0 1 Step 2 Configure service ports. huawei(config)#service-port 100 vlan 4004 vdsl mode ptm 0/1/0 multi-service user- vlan untagged rx-cttr 6 tx-cttr 6 huawei(config)#service-port 101 vlan 4005 vdsl mode ptm 0/1/1 multi-service user-...
Page 440 If the IGMP version of the multicast VLAN is V3, the source IP address of the program in the multicast VLAN must be configured. If the IGMP version of the multicast VLAN is V2, the source IP address of the program in the multicast VLAN cannot be configured. huawei(config-mvlan4002)#igmp program add name program1 ip 224.1.1.1 sourceip 10.10.10.10 huawei(config-mvlan4002)#multicast-vlan 4003 huawei(config-mvlan4003)#igmp program add name program2 ip 224.1.1.2 sourceip...
Page 441: Configuration Example Of The Multicast Video Service (Dynamic Generation Mode)
SmartAX MA5616 Multi-service Access Module 9 Configuration Example of Services on the MA5616 Configuration Guide Through GE Upstream Transmission Configure the multicast uplink port, multicast programs, and multicast users. igmp uplink-port 0/0/1 multicast-vlan 4002 igmp uplink-port 0/0/1 igmp program add name program1 ip 224.1.1.1 sourceip 10.10.10.10 multicast-vlan 4003 igmp program add name program2 ip 224.1.1.2 sourceip 10.10.10.11...
Page 442 SmartAX MA5616 Multi-service Access Module 9 Configuration Example of Services on the MA5616 Configuration Guide Through GE Upstream Transmission Figure 9-6 Example network of the multicast service Data Plan Table 9-2 provides the data plan for configuring the multicast service.
Page 443 Step 1 Create VLANs and add an uplink port to the VLANs. huawei(config)#vlan 4002-4005 smart huawei(config)#port vlan 4002-4005 0/0 1 Step 2 Configure service ports. huawei(config)#service-port 100 vlan 4004 vdsl mode ptm 0/1/0 multi-service user- vlan untagged rx-cttr 6 tx-cttr 6 huawei(config)#service-port 101 vlan 4005 vdsl mode ptm 0/1/1 multi-service user-...
Page 444 Therefore, plan the multicast program mode before configuring the multicast program. This command can be executed only when the IGMP function is disabled. huawei(config-mvlan4002)#igmp match mode disable huawei(config-mvlan4002)#igmp match group ip 224.1.1.1 to-ip 224.1.1.2 huawei(config-mvlan4002)#multicast-vlan 4003 huawei(config-mvlan4003)#igmp match mode disable huawei(config-mvlan4003)#igmp match group ip 224.1.1.1 to-ip 224.1.1.2...
Page 445: Configuration Example Of The Voip Service
SmartAX MA5616 Multi-service Access Module 9 Configuration Example of Services on the MA5616 Configuration Guide Through GE Upstream Transmission Configure the multicast uplink port, multicast programs, and multicast users. igmp uplink-port 0/0/1 multicast-vlan 4002 igmp uplink-port 0/0/1 igmp match mode disable igmp match group ip 224.1.1.1 to-ip 224.1.1.2...
Page 446 SmartAX MA5616 Multi-service Access Module 9 Configuration Example of Services on the MA5616 Configuration Guide Through GE Upstream Transmission Figure 9-7 Example network of the VoIP service based on the H.248 protocol BRAS Router Media and signaling uplink VLAN: Standard VLAN 20...
Page 447 SmartAX MA5616 Multi-service Access Module 9 Configuration Example of Services on the MA5616 Configuration Guide Through GE Upstream Transmission Item Data configuration Media IP address These two IP addresses are both on the MGC.) and signaling IP 10.10.10.10. address Default IP address...
Page 448 SmartAX MA5616 Multi-service Access Module 9 Configuration Example of Services on the MA5616 Configuration Guide Through GE Upstream Transmission Item Data Software Parameters of an According to the Context in Software MG Interface Parameters of an MG Interface confirmed with the engineers of the office, the default configuration can meet the service requirements.
Page 449 SmartAX MA5616 Multi-service Access Module 9 Configuration Example of Services on the MA5616 Configuration Guide Through GE Upstream Transmission Item Data User priority Users are common users, and the user priority uses the default priority, namely, cat3. User type Users are common users, and the user type uses the default user type, namely, DEL.
Page 450 Step 5 Configure the TID template of the PSTN user on MG interface 0. Configure the TID generation mode. According to the data plan, the terminal prefix of the PSTN user needs to be configured to huawei, and the TID template adopts layering template 6. Issue 04 (2011-10-30) Huawei Proprietary and Confidential Copyright ©...
Page 451 SmartAX MA5616 Multi-service Access Module 9 Configuration Example of Services on the MA5616 Configuration Guide Through GE Upstream Transmission CAUTION The MA5616 requires that the terminal prefixes of PSTN users, ISDN BRA users, and ISDN PRA users on the same H.248 interface are either the same or different. Note this when configuring the terminal prefix.
Page 452 If the MGC is configured with the call forwarding service, cancel the call forwarding service on the MGC. l If the MGC is not configured with the call forwarding service, contact Huawei technical support engineer to handle the fault.
Page 453: Configuration Example Of The Voip Pstn Service (Based On The Sip Protocol)
SmartAX MA5616 Multi-service Access Module 9 Configuration Example of Services on the MA5616 Configuration Guide Through GE Upstream Transmission mg-ringmode add 0 0 4 Configure the TID template of the PSTN user on the MG interface. tid-format pstn prefix huawei template 6 An MG interface must be started manually and the configuration file cannot be imported directly.
Page 454 SmartAX MA5616 Multi-service Access Module 9 Configuration Example of Services on the MA5616 Configuration Guide Through GE Upstream Transmission Figure 9-8 Example network of the VoIP PSTN service based on the SIP protocol Data Plan Run the display system parameters and display oversea parameters commands to query the system parameters and overseas parameters.
Page 455 Configure the data of the PSTN users (phone 0-phone 31) in slot 0/3. huawei(config)#esl user huawei(config-esl-user)#sippstnuser batadd 0/3/0 0/3/31 0 telno 83110000 Configure the priority of the PSTN user in slot 0/3/0 to Cat2. huawei(config-esl-user)#sippstnuser attribute set 0/3/0 priority cat2 Configure the type of the PSTN user in slot 0/3.
Page 456: Configuration Example Of The Voip Isdn Bra Service
If the IMS is configured with the call forwarding service, cancel the call forwarding service on the IMS. l If the IMS is not configured with the call forwarding service, contact Huawei technical support engineer to handle the fault.
Page 457 SmartAX MA5616 Multi-service Access Module 9 Configuration Example of Services on the MA5616 Configuration Guide Through GE Upstream Transmission board, thus implementing the ISDN BRA service. The ISDN BRA service on the MA5616 can be supported only by the H.248 protocol.
Page 458 SmartAX MA5616 Multi-service Access Module 9 Configuration Example of Services on the MA5616 Configuration Guide Through GE Upstream Transmission Figure 9-9 Example network for configuring the ISDN BRA service Data Plan Table 9-5 provides the data plan for configuring the ISDN BRA service.
Page 459 SmartAX MA5616 Multi-service Access Module 9 Configuration Example of Services on the MA5616 Configuration Guide Through GE Upstream Transmission Item Data Default media gateway of 10.13.1.1 the MG interface TID profile ID of the TID profile used 2 (default, no configuration is required)
Page 460 SmartAX MA5616 Multi-service Access Module 9 Configuration Example of Services on the MA5616 Configuration Guide Through GE Upstream Transmission Item Data Local port ID 1401 Local IP address 10.13.4.116/16 MGC port ID 1400 IP address of the primary 10.14.1.2/16 (IP address of the primary MGC)
Page 461 Step 11 Add an ISDN BRA user and configure the data. huawei(config-sigtran)#quit huawei(config)#esl user huawei(config-esl-user)#mgbrauser add 0/4/0 0 0 interfaceid 0 terminalid 2 priority cat3 telno 83110001 Are you sure to configure the working mode of the DSL board to normal and reset...
Page 462 SmartAX MA5616 Multi-service Access Module 9 Configuration Example of Services on the MA5616 Configuration Guide Through GE Upstream Transmission When ISDN phone3 dials number 83110001, ISDN phone1 and ISDN phone2 can hear the ringing tone at the same time. In addition, ISDN phone1 and ISDN phone2 can communicate with ISDN phone3 at the same time.
Page 463: Configuration Example Of The Vlan Stacking Wholesale Service
SmartAX MA5616 Multi-service Access Module 9 Configuration Example of Services on the MA5616 Configuration Guide Through GE Upstream Transmission mgbrauser add 0/4/0 0 0 interfaceid 0 terminalid 2 priority cat3 telno 83110001 mgbrauser add 0/4/1 0 0 interfaceid 2 terminalid 4 priority cat1 telno 83110002 Save the data.
Page 464 SmartAX MA5616 Multi-service Access Module 9 Configuration Example of Services on the MA5616 Configuration Guide Through GE Upstream Transmission Figure 9-10 Example network for configuring the VLAN stacking wholesale service VLAN ID:101 VLAN ID:100 ISP2 ISP1 LAN Switch BRAS BRAS...
Page 465 VLAN stacking on the MA5616. You can also run the stacking inner-ethertype command to set the type of inner Ethernet protocol supported by VLAN stacking on the MA5616. To ensure that Huawei device is interconnected with the device of other vendors, the type of the inner/outer Ethernet protocol must be the same as that of the interconnect device.
Page 466 SmartAX MA5616 Multi-service Access Module 9 Configuration Example of Services on the MA5616 Configuration Guide Through GE Upstream Transmission pppoe rx-cttr 6 tx-cttr 6 Step 5 Set the inner VLAN tag. The inner VLAN tag is used to identify the user. An inner VLAN tag under the same ISP must be unique.
Page 467: Configuration Example Of The Vlan Id Extension Service
SmartAX MA5616 Multi-service Access Module 9 Configuration Example of Services on the MA5616 Configuration Guide Through GE Upstream Transmission port vlan 100 to 101 0/0 1 service-port 1 vlan 100 vdsl mode ptm 0/1/0 multi-service user-encap pppoe rx-cttr tx-cttr 6...
Page 468 SmartAX MA5616 Multi-service Access Module 9 Configuration Example of Services on the MA5616 Configuration Guide Through GE Upstream Transmission Figure 9-11 Example network for configuring the VLAN ID extension BRAS VLAN 100 VLAN 101 MA5616_A MA5616_B User 1 User 2 User 3 User 4...
Page 469 Add an uplink port to the VLAN. huawei(config)#port vlan 100 0/0 1 Add service ports to the VLAN. huawei(config)#service-port vlan 100 vdsl mode ptm 0/1/2 multi-service user-encap pppoe rx-cttr 6 tx-cttr 6 huawei(config)#service-port vlan 100 vdsl mode ptm 0/1/3 multi-service...
Page 470 SmartAX MA5616 Multi-service Access Module 9 Configuration Example of Services on the MA5616 Configuration Guide Through GE Upstream Transmission The procedure for configuring the VLAN ID extension on MA5616_B is as follows: The configuration procedure of MA5616_B is the same as the configuration procedure of MA5616_A.
Page 471: Configuring The Triple Play Service
SmartAX MA5616 Multi-service Access Module 9 Configuration Example of Services on the MA5616 Configuration Guide Through GE Upstream Transmission tx-cttr 6 service-port 1 vlan 101 vdsl mode ptm 0/1/3 multi-service user-encap pppoe rx-cttr tx-cttr 6 Set the inner VLAN tag.
Page 472 SmartAX MA5616 Multi-service Access Module 9 Configuration Example of Services on the MA5616 Configuration Guide Through GE Upstream Transmission Figure 9-12 Example network for configuring the triple play service based on the user-side VLAN OSS & RADIUS Server/ Multicase Sever...
Page 473 SmartAX MA5616 Multi-service Access Module 9 Configuration Example of Services on the MA5616 Configuration Guide Through GE Upstream Transmission Item Data Uplink port 0/0/1 Upstream Internet service: smart VLAN 102 VLANs VoIP service: smart VLAN 103 IPTV service: smart VLAN 104...
Page 474 Add service ports to the VLAN. Add service ports to the VLAN and use the traffic profile configured in the preceding step. huawei(config)#service-port vlan 102 vdsl mode atm 0/1/0 vpi 0 vci 35 multi-serv ice user-vlan 2 rx-cttr 7 tx-cttr 7...
Page 475 Add service ports to the VLAN. Add service ports to the VLAN and use the traffic profile configured in the preceding step. huawei(config)#service-port vlan 103 vdsl mode atm 0/1/0 vpi 0 vci 35 multi-serv ice user-vlan 3 rx-cttr 8 tx-cttr 8...
Page 476 9 Configuration Example of Services on the MA5616 Configuration Guide Through GE Upstream Transmission huawei(config)#service-port 10 vlan 105 vdsl mode atm 0/1/0 vpi 0 vci 35 multi-serv ice user-vlan 4 rx-cttr 9 tx-cttr 9 huawei(config)#service-port 11 vlan 105 vdsl mode atm 0/1/1 vpi 0 vci 35...
Page 477 SmartAX MA5616 Multi-service Access Module 9 Configuration Example of Services on the MA5616 Configuration Guide Through GE Upstream Transmission Result After the related upstream device and downstream device are configured, the triple play service (Internet, VoIP, and IPTV services) is available.
Page 478: Configuration Example Of The Triple Play Service - Single Pvc For Multiple Services Based On The User-Side 802.1P
SmartAX MA5616 Multi-service Access Module 9 Configuration Example of Services on the MA5616 Configuration Guide Through GE Upstream Transmission quit save 9.5.2 Configuration Example of the Triple Play Service - Single PVC for Multiple Services Based on the User-Side 802.1p This topic describes how to configure the triple play service in the single-PVC for multiple services mode based on the user-side 802.1p priority.
Page 479 SmartAX MA5616 Multi-service Access Module 9 Configuration Example of Services on the MA5616 Configuration Guide Through GE Upstream Transmission Figure 9-14 Example network for configuring the triple play service in the single-PVC for multiple services mode based on the user-side 802.1p priority OSS &...
Page 480 SmartAX MA5616 Multi-service Access Module 9 Configuration Example of Services on the MA5616 Configuration Guide Through GE Upstream Transmission Item Data Traffic Internet service: 1 Mbit/s profile VoIP service: 64 Kbit/s parameters IPTV service: no limit Uplink port 0/0/1 Upstream...
Page 481 Add service ports to the VLAN. Add service ports to the VLAN and use the traffic profile configured in the preceding step. huawei(config)#service-port vlan 102 vdsl mode atm 0/1/0 vpi 0 vci 35 multi-serv ice user-8021p 2 rx-cttr 7 tx-cttr 7...
Page 482 Add service ports to the VLAN. Add service ports to the VLAN and use the traffic profile configured in the preceding step. huawei(config)#service-port vlan 103 vdsl mode atm 0/1/0 vpi 0 vci 35 multi-serv ice user-8021p 3 rx-cttr 8 tx-cttr 8...
Page 483 9 Configuration Example of Services on the MA5616 Configuration Guide Through GE Upstream Transmission huawei(config)#service-port 10 vlan 105 vdsl mode atm 0/1/0 vpi 0 vci 35 multi-serv ice user-8021p 4 rx-cttr 9 tx-cttr 9 huawei(config)#service-port 11 vlan 105 vdsl mode atm 0/1/1 vpi 0 vci 35...
Page 484 SmartAX MA5616 Multi-service Access Module 9 Configuration Example of Services on the MA5616 Configuration Guide Through GE Upstream Transmission Result After the related upstream device and downstream device are configured, the triple play service (Internet, VoIP, and IPTV services) is available.
Page 485: Configuration Example Of The Triple Play Service - Multiple Pvcs For Multiple Services
SmartAX MA5616 Multi-service Access Module 9 Configuration Example of Services on the MA5616 Configuration Guide Through GE Upstream Transmission quit save 9.5.3 Configuration Example of the Triple Play Service - Multiple PVCs for Multiple Services This topic describes how to configure the triple play service in the multi-PVC for multiple services mode.
Page 486 SmartAX MA5616 Multi-service Access Module 9 Configuration Example of Services on the MA5616 Configuration Guide Through GE Upstream Transmission Figure 9-16 Example network of the triple play service in the multi-PVC for multiple services mode OSS & RADIUS Server/ Multicase Sever...
Page 487 SmartAX MA5616 Multi-service Access Module 9 Configuration Example of Services on the MA5616 Configuration Guide Through GE Upstream Transmission Item Data VPI/VCI for the Internet service: 0/37 VPI/VCI for the VoIP service: 0/36 VPI/VCI for the IPTV service: 0/35 Traffic...
Page 488 Add service ports to the VLAN and use the traffic profile configured in the preceding step. huawei(config)#service-port vlan 102 vdsl mode atm 0/1/0 vpi 0 vci 37 rx- cttr 7 tx-cttr 7 huawei(config)#service-port vlan 102 vdsl mode atm 0/1/1 vpi 0 vci 37 rx- cttr 7 tx-cttr 7 Save the data.
Page 489 Add service ports to the VLAN and use the traffic profile configured in the preceding step. huawei(config)#service-port vlan 103 vdsl mode atm 0/1/0 vpi 0 vci 36 rx- cttr 8 tx-cttr 8 huawei(config)#service-port vlan 103 vdsl mode atm 0/1/1 vpi 0 vci 36 rx- cttr 8 tx-cttr 8 Save the data.
Page 490 Are you sure to change the uplink port mode?(y/n)[n]:y Configure the program library. huawei(config-btv)#multicast-vlan 104 huawei(config-mvlan104)#igmp program add name program1 ip 224.1.1.1 sourceip 10. 10.10.10 huawei(config-mvlan104)#igmp program add name program2 ip 224.1.1.2 sourceip 10. 10.10.11 Configure the right profile.
Page 491 SmartAX MA5616 Multi-service Access Module 9 Configuration Example of Services on the MA5616 Configuration Guide Through GE Upstream Transmission The IPTV user on port 0/1/0 can watch all the programs, and the IPTV user on port 0/1/1 can watch program 1 only.
Page 492: Configuration Examples Of The Fttx
SmartAX MA5616 Multi-service Access Module Configuration Guide 10 Configuration Examples of the FTTx Configuration Examples of the FTTx About This Chapter The FTTx solution configuration guide describes how to configure typical FTTH, FTTB/C, FTTO, and FTTM services (such as high-speed Internet access, multicast, VoIP, and mobile backhaul services) on the OLT and the ONU step by step through examples.
Page 493: Fttx Network And Product
SmartAX MA5616 Multi-service Access Module Configuration Guide 10 Configuration Examples of the FTTx 10.1 FTTx Network and Product FTTx applications include FTTH, FTTB, FTTC, FTTO, Base station access, and VIP P2P access. Network Figure 10-1 shows an example network of full access services in the FTTx scenario. FTTx applications include FTTH, FTTB, FTTC, FTTO, Base station access, and VIP P2P access.
Page 494: Fttx Data Plan (Gpon Access)
SmartAX MA5616 Multi-service Access Module Configuration Guide 10 Configuration Examples of the FTTx Configuration Products Table 10-1 lists the configuration products for the FTTx solution. Table 10-1 Configuration products for the FTTx solution Network Configuration Product Version Description Positioni MA5600T and MA5603T...
Page 495 SmartAX MA5616 Multi-service Access Module Configuration Guide 10 Configuration Examples of the FTTx Table 10-2 Data plan for the FTTx GPON access Servic Item Data Remarks Classif ication Networ FTTH OLT PON port: In the current network, FTTH, FTTB, and...
Page 496 SmartAX MA5616 Multi-service Access Module Configuration Guide 10 Configuration Examples of the FTTx Servic Item Data Remarks Classif ication Service HSI service ONU upstream For the Internet access service, you can use VLAN VLAN: 1001-1016 two precisely-bound VLAN tags to extend VLANs and identify users.
Page 497 SmartAX MA5616 Multi-service Access Module Configuration Guide 10 Configuration Examples of the FTTx Servic Item Data Remarks Classif ication The queue scheduling mode is configured schedul IPTV service Priority: 4; queue globally. Queues with higher priorities ing) scheduling: WRR adopt PQ mode and queues with lower VoIP service Priority: 6;...
Page 498 SmartAX MA5616 Multi-service Access Module Configuration Guide 10 Configuration Examples of the FTTx Servic Item Data Remarks Classif ication VoIP service l Profile name: VOIP l Profile type: Type3 l Assured bandwidth (FTTH): 0.1 Mbit/s l Maximum bandwidth (FTTH): 1 Mbit/...
Page 499 SmartAX MA5616 Multi-service Access Module Configuration Guide 10 Configuration Examples of the FTTx Servic Item Data Remarks Classif ication QinQ private l Profile name: line service PrivateLine l Profile type: Type3 l Assured bandwidth: 20 Mbit/s l Maximum bandwidth: 50...
Page 500 SmartAX MA5616 Multi-service Access Module Configuration Guide 10 Configuration Examples of the FTTx Servic Item Data Remarks Classif ication IP address of 10.10.10.10 the multicast server Multicast 224.1.1.10 program VoIP Signaling 17.10.10.10/24 H.248 and SIP support separate media and service and media IP signaling.
Page 501 SmartAX MA5616 Multi-service Access Module Configuration Guide 10 Configuration Examples of the FTTx Servic Item Data Remarks Classif ication Index of the profile Different profile indexes are used for used by the MG interconnection with non-Huawei interface softswitches. You can run the if-h248 attribute profile-index command to query the profile index.
Page 502: Configuring Upstream Link Aggregation
SmartAX MA5616 Multi-service Access Module Configuration Guide 10 Configuration Examples of the FTTx Servic Item Data Remarks Classif ication User priorities: According to the service requirements, user Phone 1: Cat2; priorities must be specified. The user Phone 2-Phone 24: priorities include the following:...
Page 503: Configuring The Fttb And Fttc Access Services
SmartAX MA5616 Multi-service Access Module Configuration Guide 10 Configuration Examples of the FTTx Procedure Step 1 Configure an aggregation group. Configure upstream ports 0/19/0 and 0/19/1 as an aggregation group. Each member port in the aggregation group is allocated with packets according to the source MAC address. The working mode is LACP static aggregation.
Page 504: Configuring The Fttb And Fttc Internet Access Services (Adsl2+ Access)
SmartAX MA5616 Multi-service Access Module Configuration Guide 10 Configuration Examples of the FTTx Figure 10-2 Example network of the multiple service in FTTB and FTTC service 10.4.1 Configuring the FTTB and FTTC Internet Access Services (ADSL2+ Access) The OLT is connected to a remote ONU that supports ADSL2+ access by using the GPON port to provide users with the high-speed Internet access service.
Page 505 Configure the DBA profile name to PPPoE, type to Type4, and maximum bandwidth to 100 Mbit/s. huawei(config)#dba-profile add profile-name PPPoE type4 max 102400 Configure an ONU line profile. Create GPON ONU line profile 10 and bind T-CONT 4 to DBA profile PPPoE.
Page 506 SmartAX MA5616 Multi-service Access Module Configuration Guide 10 Configuration Examples of the FTTx huawei(config-gpon-lineprofile-10)#gem add 0 eth tcont 4 huawei(config-gpon-lineprofile-10)#gem add 1 eth tcont 4 NOTE a. To change the QoS mode, run the qos-mode command to configure the QoS mode to gem- car or flow-car, and run the gem add command to configure the ID of the traffic profile bound to the GEM port.
Page 507 SmartAX MA5616 Multi-service Access Module Configuration Guide 10 Configuration Examples of the FTTx – Automatically find an ONU: If the password or SN of an ONU is unknown, run the port ont-auto-find command in the GPON mode to enable the ONU auto-find function of the GPON port.
Page 508 SmartAX MA5616 Multi-service Access Module Configuration Guide 10 Configuration Examples of the FTTx After an ONU is added, run the display ont info command to query the current status of the ONU. Ensure that Control flag of the ONU is active, Run State is online, and Config state is normal.
Page 509 1 vlan 8 gpon 0/2/1 ont 1 gemport 0 multi- service user-vlan 8 rx-cttr 6 tx-cttr 6...
Page 510 10 10 20 20 40 0 0 0 Configure the mapping between the queues and 802.1p priorities. Priorities 0-7 map queues 0-7 respectively. huawei(config)#cos-queue-map cos0 0 cos1 1 cos2 2 cos3 3 cos4 4 cos5 5 cos6 6 cos7 7 10. Save the data.
Page 511 8, VCI 35, CVLAN untagged. The other service virtual ports can be added similarly by replacing the right SVLAN and the ADSL2+ port ID. huawei(config)#service-port 101 vlan 1001 adsl 0/1/1 vpi 8 vci 35 multi- service user-vlan untagged rx-cttr 8 tx-cttr 8...
Page 512 SmartAX MA5616 Multi-service Access Module Configuration Guide 10 Configuration Examples of the FTTx NOTE In the case of batch service provisioning, run the multi-service-port command to add service ports in batches. 10. Save the data. huawei(config)#save ----End Result Users can enjoy the high-speed Internet service with PC by PPPoE.
Page 513: Configuring The Fttb And Fttc Internet Access Services (Vdsl2 Access)
SmartAX MA5616 Multi-service Access Module Configuration Guide 10 Configuration Examples of the FTTx interface gpon 0/2 port 1 ont-auto-find enable ont confirm 1 ontid 1 sn-auth 32303131B39FD641 snmp ont-lineprofile-id 10 ont confirm 1 ontid 2 sn-auth 32303131B39FD642 snmp ont-lineprofile-id 10...
Page 514 DBA profile. Configure the DBA profile name to PPPoE, type to Type4, and maximum bandwidth to 100 Mbit/s. huawei(config)#dba-profile add profile-name PPPoE type4 max 102400 Configure an ONU line profile. Issue 04 (2011-10-30) Huawei Proprietary and Confidential...
Page 515 SmartAX MA5616 Multi-service Access Module Configuration Guide 10 Configuration Examples of the FTTx Create GPON ONU line profile 10 and bind T-CONT 4 to DBA profile PPPoE. In this way, the T-CONT can provide flexible DBA solutions based on different configurations in the DBA profile.
Page 516 SmartAX MA5616 Multi-service Access Module Configuration Guide 10 Configuration Examples of the FTTx – Run the gpon alarm-profile add command to configure an alarm profile, which is used for monitoring the performance of an activated ONU line. Add an ONU on the OLT.
Page 517 SmartAX MA5616 Multi-service Access Module Configuration Guide 10 Configuration Examples of the FTTx 32303131B39FD641 snmp ont-lineprofile-id 10 huawei(config-if-gpon-0/2)#ont confirm 1 ontid 2 sn-auth 32303131B39FD642 snmp ont-lineprofile-id 10 (Optional) Bind an alarm profile to the ONU. After an alarm profile is configured, bind it to the ONT. In this example, bind the default alarm profile, namely alarm profile 1 to the ONU.
Page 518 1 vlan 8 gpon 0/2/1 ont 1 gemport 0 multi- service user-vlan 8 rx-cttr 6 tx-cttr 6...
Page 519 10 10 20 20 40 0 0 0 Configure the mapping between the queues and 802.1p priorities. Priorities 0-7 map queues 0-7 respectively. huawei(config)#cos-queue-map cos0 0 cos1 1 cos2 2 cos3 3 cos4 4 cos5 5 cos6 6 cos7 7 10. Save the data.
Page 520 Step 5 Set the downstream rate adaptation ratio to 100% and the upstream rate adaptation ratio to 100%. huawei(config)#vdsl line-template quickadd 3 line 4 channel1 4 100 100 Activate VDSL2 port 0/1/0 and bind line template 3 to it. NOTE The other VDSL2 ports can be activated similarly.
Page 521 PTM, CVLAN untagged. The other service virtual ports can be added similarly by replacing the right SVLAN and the VDSL port ID. huawei(config)#service-port 101 vlan 1001 vdsl mode ptm 0/1/0 multi- service user-vlan untagged rx-cttr 8 tx-cttr 8 NOTE In the case of batch service provisioning, run the multi-service-port command to add service ports in batches.
Page 522: Configuring The Fttb And Fttc Voip Services (Based On The H.248 Protocol)
SmartAX MA5616 Multi-service Access Module Configuration Guide 10 Configuration Examples of the FTTx Configuration File On the OLT side. vlan 100 smart vlan attrib 100 satcking port vlan 100 0/19 0 dba-profile add profile-name PPPOE type4 max 102400 ont-lineprofile gpon profile-id 10...
Page 523 SmartAX MA5616 Multi-service Access Module Configuration Guide 10 Configuration Examples of the FTTx Service Requirements Users directly uses the existing phone sets for the voice service and no additional investment is required. The voice data is carried over the IP network, which reduces the communication costs to a great extent without compromising the communication quality.
Page 524 Configure the DBA profile name to VoIP, type to Type4, assure bandwidth to 15 Mbit/s and maximum bandwidth to 30 Mbit/s. huawei(config)#dba-profile add profile-name VoIP type3 assure 15360 max 30720 Configure an ONU line profile. Create GPON ONU line profile 10 and bind T-CONT 2 to DBA profile VoIP.
Page 525 SmartAX MA5616 Multi-service Access Module Configuration Guide 10 Configuration Examples of the FTTx Configure the mapping between the GEM port and the ONU-side service to the VLAN mapping mode (default), map the service port of management (the CVLAN ID is 8) to GEM port 0, and map the service port of VoIP service (the CVLAN ID is 200) to GEM port 1.
Page 526 SmartAX MA5616 Multi-service Access Module Configuration Guide 10 Configuration Examples of the FTTx Checkcode VenderID : HWTC Ont Version : MA5616 VER.B Ont SoftwareVersion : V8R309 C00 Ont EquipmentID : SmartAX MA5616 Ont autofind time : 2011-05-10 10:06:00+08:00 --------------------------------------------------------------------- Number...
Page 527 1 vlan 8 gpon 0/2/1 ont 1 gemport 0 multi- service user-vlan 8 rx-cttr 6 tx-cttr 6...
Page 528 10 10 20 20 40 0 0 0 Configure the mapping between the queues and 802.1p priorities. Priorities 0-7 map queues 0-7 respectively. huawei(config)#cos-queue-map cos0 0 cos1 1 cos2 2 cos3 3 cos4 4 cos5 5 cos6 6 cos7 7 11. Save the data.
Page 529 SmartAX MA5616 Multi-service Access Module Configuration Guide 10 Configuration Examples of the FTTx NOTE l The VLAN ID must be consistent with the CVLAN of the OLT. l The VLAN ID of the default upstream Ethernet port is 1. Use the default VLAN if no specific VLAN is required for the upstream transmission.
Page 530 The terminal ID must be unique on one MG interface. huawei(config)#esl user huawei(config-esl-user)#mgpstnuser batadd 0/2/0 0/2/23 0 terminalid 0 telno 83110001 Change the call priority of the PSTN user. Configure the call priority of the user on port 0/2/0 to Cat2 and the users of 0/2/1 to...
Page 531 SmartAX MA5616 Multi-service Access Module Configuration Guide 10 Configuration Examples of the FTTx When the caller dials the phone number of the callee, the phone of the callee can ring normally, and the caller can hear the ringback tone. The caller and the callee can communicate with each other successfully.
Page 532: Configuring The Fttb And Fttc Voip Services (Based On The Sip Protocol)
SmartAX MA5616 Multi-service Access Module Configuration Guide 10 Configuration Examples of the FTTx reset coldstart quit esl user mgpstnuser batadd 0/2/0 0/2/23 0 terminalid 0 telno 83110001 mgpstnuser modify 0/2/0 priority cat2 quit pstnport pstnport attribute batset 0/2/0 0/2/23 reverse-pole-pulse enable...
Page 533 Configure the DBA profile name to VoIP, type to Type4, assure bandwidth to 15 Mbit/s and maximum bandwidth to 30 Mbit/s. huawei(config)#dba-profile add profile-name VoIP type3 assure 15360 max 30720 Configure an ONU line profile. Create GPON ONU line profile 10 and bind T-CONT 2 to DBA profile VoIP.
Page 534 SmartAX MA5616 Multi-service Access Module Configuration Guide 10 Configuration Examples of the FTTx NOTE a. To change the QoS mode, run the qos-mode command to configure the QoS mode to gem- car or flow-car, and run the gem add command to configure the ID of the traffic profile bound to the GEM port.
Page 535 SmartAX MA5616 Multi-service Access Module Configuration Guide 10 Configuration Examples of the FTTx – Automatically find an ONU: If the password or SN of an ONU is unknown, run the port ont-auto-find command in the GPON mode to enable the ONU auto-find function of the GPON port.
Page 536 SmartAX MA5616 Multi-service Access Module Configuration Guide 10 Configuration Examples of the FTTx After an ONU is added, run the display ont info command to query the current status of the ONU. Ensure that Control flag of the ONU is active, Run State is online, and Config state is normal.
Page 537 1 vlan 8 gpon 0/2/1 ont 1 gemport 0 multi- service user-vlan 8 rx-cttr 6 tx-cttr 6...
Page 538 10 10 20 20 40 0 0 0 Configure the mapping between the queues and 802.1p priorities. Priorities 0-7 map queues 0-7 respectively. huawei(config)#cos-queue-map cos0 0 cos1 1 cos2 2 cos3 3 cos4 4 cos5 5 cos6 6 cos7 7 11. Save the data.
Page 539 – Signaling port ID of the primary IMS: 5060 – Media IP address 1: 17.10.10.10 – Homing domain name of SIP interface: huawei – SIP profile ID: 1 When the ONU is MA5616 with version of V800R306, run the command as follows: huawei(config-if-sip-0)#if-sip attribute basic media-ip 17.10.10.10...
Page 540 SmartAX MA5616 Multi-service Access Module Configuration Guide 10 Configuration Examples of the FTTx Modify the attributes of the PSTN port 0/2/0 to 0/2/23 so that the PSTN ports support the polarity reversal. huawei(config)#pstnport huawei(config-pstnport)#pstnport attribute batset 0/2/0 0/2/23 reverse- pole-pulse enable huawei(config-pstnport)#quit 12.
Page 541: Configuring The Fttb And Fttc Iptv Multicast Services
//When the ONU is MA5616 with version of V800R306 if-sip attribute basic media-ip 17.10.10.10 signal-ip 17.10.10.10 signal-port 5060 transfer udp primary-proxy-ip1 200.200.200.200 primary-proxy-port 5060 home-domain huawei sipprofile-index 1 //When the ONU is MA5603T, or MA5616 with a version newer than V800R306 reset...
Page 542 IPTV service. Bind GEM port 0 and GEM port 1 to T-CONT 3. Configure the QoS mode to priority-queue (default). huawei(config-gpon-lineprofile-10)#gem add 0 eth tcont 3 cascade on huawei(config-gpon-lineprofile-10)#gem add 1 eth tcont 3 cascade on...
Page 543 SmartAX MA5616 Multi-service Access Module Configuration Guide 10 Configuration Examples of the FTTx NOTE a. To change the default QoS mode, run the qos-mode command to configure the QoS mode to gem-car or flow-car, and run the gem add command to configure the index of the traffic profile to which the GEM port is bound.
Page 544 SmartAX MA5616 Multi-service Access Module Configuration Guide 10 Configuration Examples of the FTTx auto-find function of the GPON port. Then, run the ont confirm command to confirm the ONU. To add an ONU offline, do as follows: huawei(config)#interface gpon 0/2...
Page 545 SmartAX MA5616 Multi-service Access Module Configuration Guide 10 Configuration Examples of the FTTx huawei(config-if-gpon-0/2)#display ont info 1 1 --------------------------------------------------------------------- F/S/P 0/2/1 ONT-ID Control flag : active //Indicates that the ONU is activated. Run state : online //Indicates that the ONU already goes online normally.
Page 546 10 10 20 20 40 0 0 0 Configure the mapping between the queues and 802.1p priorities. Priorities 0-7 map queues 0-7 respectively. huawei(config)#cos-queue-map cos0 0 cos1 1 cos2 2 cos3 3 cos4 4 cos5 5 cos6 6 cos7 7 10. Configure a multicast subtending port.
Page 547 15. Configure the program library. The multicast IP address of the program is 224.1.1.10 and the IP address of the program source is 10.10.10.10 huawei(config-mvlan10000)#igmp program add name program1 ip 224.1.1.10 sourceip 10.10.10.10 16. Configure a log server. Enable CDR log reporting, and configure the IP address of the active server to 10.10.10.20.
Page 548 In xDSL access mode, xDSL ports must be activated before service ports are created. l The SVLAN must be the same as the CVLAN on the OLT. huawei(config)#service-port 100 vlan 1000 adsl 0/3/1 vpi 0 vci 35 rx-cttr 10 tx-cttr 10 Configure the multicast mode and multicast protocol version.
Page 549 SmartAX MA5616 Multi-service Access Module Configuration Guide 10 Configuration Examples of the FTTx Result The user can watch program 1 on the TV. Configuration File On the OLT side. vlan 1000 smart port vlan 1000 0/19 0 dba-profile add profile-name IPTV type4 max 61440...
Page 550 SmartAX MA5616 Multi-service Access Module Configuration Guide 10 Configuration Examples of the FTTx igmp mode proxy igmp uplink-port 0/0/1 igmp program add name program1 ip 224.1.1.10 sourceip 10.10.10.10 igmp user add service-port 100 no-auth multicast-vlan 1000 igmp multicast-vlan member service-port 100...
Page 551: A Acronyms And Abbreviations
SmartAX MA5616 Multi-service Access Module Configuration Guide A Acronyms and Abbreviations Acronyms and Abbreviations ADSL Asymmetrical Digital Subscriber Line Access Gateway BRAS Broadband Remote Access Server Broadband TV Committed Access Rate Committed Information Rate Command Line Interface DHCP Dynamic Host Configuration Protocol...
Page 552 SmartAX MA5616 Multi-service Access Module Configuration Guide A Acronyms and Abbreviations File Transfer Protocol Gigabit Ethernet GPON Encapsulation Method GPON Gigabit-capable Passive Optical Networks Internet Protocol IPoA Internet Protocol Over ATM IPoE IP over Ethernet Local Area Network Medium Access Control...
Page 553 SmartAX MA5616 Multi-service Access Module Configuration Guide A Acronyms and Abbreviations PITP Policy Information Transfer Protocol Passive Optical Network POTS Plain Old Telephone Service PPPoA Point-to-Point Protocol Over ATM PPPoE Point-to-Point Protocol Over Ethernet PSTN Public Switched Telephone Network Quality of Service...

Huawei SmartAX MA5616 Configuration Manual

About this Document

1 Deploying Network Devices

2 Checking before the Configuration

3 Basic Configuration

4 Configuring the Ethernet CFM OAM

5 Configuring the Xdsl Internet Access Service

6 Configuring the Multicast Service (Multicast VLAN Mode)

7 Configuring the Voice Service

8 Configuration Example of Services on the MA5616 through GPON Upstream Transmission

9 Configuration Example of Services on the MA5616 through GE Upstream Transmission

10 Configuration Examples of the Fttx

A Acronyms and Abbreviations

Quick Links

Related Manuals for Huawei SmartAX MA5616

Summary of Contents for Huawei SmartAX MA5616