Swegon Actionair ThermShield FD Installation Manual
  1. Manuals
  2. Brands
  3. Swegon Manuals
  4. Fire and Smoke Dampers
  5. Actionair ThermShield FD
  6. Installation manual
Swegon Actionair ThermShield FD Installation Manual

Swegon Actionair ThermShield FD Installation Manual

Mf on wall / floor installation method
Hide thumbs Also See for Actionair ThermShield FD:
Table of Contents

Advertisement

Quick Links

Download this manual
INSTALLATION GUIDE
ThermShield MF On Wall / Floor Installation Method
Contents
Applies to................................................................................1
Health and safety..................................................................1
CE Installation Method Overview.......................................2
Square flexible wall subframe.............................................8
(circular)................................................................................10
Circular flexible wall subframe..........................................14
Periodic maintenance.........................................................15
Actuators..............................................................................16
Wiring Diagrams..................................................................19
Dimensional Data...............................................................21
Inspection and handover check sheet............................25

Applies to...

• Actionair ThermShield FD
• Actionair Thermshield FD-C

Health and safety

• This process must be undertaken by competent
persons. More than one person may be required to
ensure the safe handling of large dampers and other
materials. Use must be made of access equipment
to ensure unsafe practices are not used to approach
walls or difficult access areas.
• Standard site PPE should be used (minimum steel
toe cap boots, hard hat); together with any pro-
tective eyewear, gloves and masks, when drilling or
cutting is being undertaken. The latter should also
be used when handing the wall construction mate-
rials, as defined by the material suppliers. If loud
equipment is being used, hearing protection should
be used.
• All waste materials should be collected and disposed
of as defined by the relevant supplier.
• Actuators: All wiring should be carried out in accor-
dance with the wiring details provided by the IEE
and BS regulations and by a competent person.
Care must be taken when installing and inspecting
dampers, as they are likely to close without war-
ning due to loss of electrical power or a temperature
rise in the ductwork. This is their prime function. Do
not insert any items, fingers or limbs between the
blades. Larger dampers must be handled in accor-
dance with current regulations and good practice
due to weight.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Actionair ThermShield FD and is the answer not in the manual?

Questions and answers

Related Manuals for Swegon Actionair ThermShield FD

Summary of Contents for Swegon Actionair ThermShield FD

  • Page 1: Table Of Contents

    INSTALLATION GUIDE ThermShield MF On Wall / Floor Installation Method Applies to... Contents Applies to................1 • Actionair ThermShield FD Health and safety..............1 • Actionair Thermshield FD-C CE Installation Method Overview........2 Health and safety Fire damper installation square openings......3 Rigid wall installation MF2 installation frame....4 •...

  • Page 2: Ce Installation Method Overview

    • Under the Fire Damper Product standard BS EN 15650 our Fire Damper products are tested to BS EN 1366-2 and classified under BS EN 13501-3. Swegon reserves the right to alter specifications. 20210615 - L00010...

  • Page 3: Fire Damper Installation Square Openings

    Check the operation of the fire damper before commencing the installation. 20210615 - L00010 Swegon reserves the right to alter specifications.

  • Page 4: Rigid Wall Installation Mf2 Installation Frame

    2. Insert fire damper into wall and fasten with screws. FD25 - 4 pieces, 6(d)x140(l) mm, FD40 - 12 pieces, 6(d)x140(l) mm Ensure that the damper is sufficiently supported. Test the operation of the damper blade. Swegon reserves the right to alter specifications. 20210615 - L00010...

  • Page 5: Flexible Wall Installation Mf2 Installation Frame

    3. Fasten the fire damper with suitable fixing screws. FD25 - 4 pieces, 6(d)x140(l) mm, FD40 - 12 pieces, 6(d)x140(l) mm Ensure that the damper is sufficiently supported. Test the operation of the damper blade. 20210615 - L00010 Swegon reserves the right to alter specifications.

  • Page 6: Shaft Wall Installation Mf2 Installation Frame

    3. Insert fire damper into wall and fasten with screws 12 pieces, 6(d) x 160(l) mm. Ensure that the damper is sufficiently supported. Test the operation of the damper blade. Swegon reserves the right to alter specifications. 20210615 - L00010...

  • Page 7: Rigid Floor/Ceiling Mf2 Installation (Square)

    (8 mm). To find B and H please see the Dimension Data section. 3. Mount between 4 and 12 sets (depending on number of fixings on damper) of threaded rods along with washer, nut and locking-nut on one side. 20210615 - L00010 Swegon reserves the right to alter specifications.

  • Page 8: Square Flexible Wall Subframe

    When installing the fire dampers in the flexible walls it is necessary to make a metal subframe onto which the damper will be fixed with screws. Subframe should be prepared according to the drawings below. Swegon reserves the right to alter specifications. 20210615 - L00010...

  • Page 9: Fire Damper Installation Circular Openings

    (except for installation with MF installation frame). Check the operation of the fire damper before commencing the installation. 20210615 - L00010 Swegon reserves the right to alter specifications.

  • Page 10: Rigid Wall Installation Mf2 Installation Frame (Circular)

    3. Fasten the fire damper with screws FDC25- 4 pieces, 6(d)x160(l) mm, FDC40- 12 pieces, 6(d)x160(l) mm. Ensure that the damper is sufficiently supported. Test the operation of the damper blade. Swegon reserves the right to alter specifications. 20210615 - L00010...

  • Page 11: Flexible Wall Installation Mf2 Installation Frame

    Test the operation of the damper blade. mandatory to use the mineral wool inside the wall (mineral wool with density up to 100 kg/m³ can be used). The minimum thickness of the wall is 100 mm. 20210615 - L00010 Swegon reserves the right to alter specifications.

  • Page 12: Shaft Wall Installation Mf2 Installation Frame

    Ensure that the damper is sufficiently 3. Insert fire damper into wall and fasten with screws (12 supported. pieces, 6(d)x140(l) mm). Test the operation of the damper blade. Test the operation of the damper blade! Swegon reserves the right to alter specifications. 20210615 - L00010...

  • Page 13: Rigid Floor/Ceiling Mf2 Installation Frame

    2. Remove the fire damper and drill the marked places (8 mm). 3. Mount between 4 and 12 sets (depending on number of fixings on damper) of threaded rods along with washer, nut and locking-nut on one 20210615 - L00010 Swegon reserves the right to alter specifications.

  • Page 14: Circular Flexible Wall Subframe

    When installing the fire dampers in the flexible walls it is necessary to make a metal subframe onto which the damper will be fixed with screws. Subframe should be prepared according to the drawings below. Swegon reserves the right to alter specifications. 20210615 - L00010...

  • Page 15: Periodic Maintenance

    • A comprehensive example of the maintenance procedure is given in Annex D of the standard. Some automatic systems may allow more frequent testing 20210615 - L00010 Swegon reserves the right to alter specifications.

  • Page 16: Actuators

    Ambient temperature min. -30 °C, max. 50 °C range 95% r.h., Ambient humidity non-condensing Service life Min. 30,000 cycles Maintenance Maintenance-free (see page 20) Weight R25/R40 0,5 kg / 1,7 kg Swegon reserves the right to alter specifications. 20210615 - L00010...
  • Page 17 < 120 s Running spring time ~ 20 s ~ 20 s ~ 20 s ~ 20 s ~16 s ~16 s return Ambient temperature min. -30 °C, max. 50 °C range 20210615 - L00010 Swegon reserves the right to alter specifications.
  • Page 18 Min. 10,000 cycles @ 10 s, min Min. 10,000 cycles @ 10 s, min Service life 1000 cycles @ 1s 1000 cycles @ 1s Maintenance Maintenance-free Maintenance-free Weight 3,5 kg 3,5 kg Swegon reserves the right to alter specifications. 20210615 - L00010...

  • Page 19: Wiring Diagrams

    (ambient temperature) max. 72 °C 20210615 - L00010 Swegon reserves the right to alter specifications.
  • Page 20 Thermal fuse is located on the underside of the fire damper. side as Belimo actuator (below). same side as Belimo actuator. Bottom View Side view Side view Electric Actuator Schischek ExMax Swegon reserves the right to alter specifications. 20210615 - L00010...

  • Page 21: Dimensional Data

    ThermShield MF On Wall Installation Method Dimensional Data FD25-MF2-R FD25-MF2-M FD40-MF2-M 20210615 - L00010 Swegon reserves the right to alter specifications.
  • Page 22 ThermShield MF On Wall Installation Method FD40-MF2-R Swegon reserves the right to alter specifications. 20210615 - L00010...
  • Page 23 ThermShield MF On Wall Installation Method Dimensional Data FDC25-MF1-R FDC25-MF1-M FDC25-MF2-R 20210615 - L00010 Swegon reserves the right to alter specifications.
  • Page 24 ThermShield MF On Wall Installation Method Dimensional Data FDC25-MF2-M FDC40-MF2-M FDC40-MF2-R Swegon reserves the right to alter specifications. 20210615 - L00010...

  • Page 25: Inspection And Handover Check Sheet

    ThermShield MF On Wall Installation Method Inspection and handover check sheet This certificate applies only to Swegon Fire Dampers. The installer must complete this installation certificate when installing fire and smoke dampers. A separate certificate must be completed for each individual fire and smoke damper.

This manual is also suitable for:

Actionair thermshield fd-cFd25-mf2-rFd25-mf2-mFd40-mf2-mFd40-mf2-rFdc25-mf1-r ... Show all

Table of Contents