Related Manuals for Titan TTB911CSW
Summary of Contents for Titan TTB911CSW
- Page 1 1500W Circular Saw TTB911CSW EAN: 5059340349978 WARNING: Read the instructions before using the product!
-
Page 2: Table Of Contents
Let’s get started These instructions are for your safety. Please read through them thoroughly before use and retain them for future reference. started... Getting Safety information Your product Before you start more detail... Product functions Operation Care and maintenance Troubleshooting Recycling and disposal Guarantee Declarations of conformity... - Page 3 TTB911CSW by TITAN Safety information Safety warnings General power tool safety warnings WARNING! Read all safety warnings, instructions, power tool. Failure to follow all instructions listed serious injury. Save all warnings and instructions for future reference. The term “power tool” in the...
-
Page 4: Safety Information
Safety information TTB911CSW by TITAN Safety warnings >Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock. - Page 5 TTB911CSW by TITAN Safety information >Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. >Do not overreach. Keep proper footing and balance at all times.
- Page 6 Safety information TTB911CSW by TITAN Safety warnings >Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
- Page 7 TTB911CSW by TITAN Safety information > Do not reach underneath the workpiece. The guard cannot protect you from the blade below the workpiece. >Adjust the cutting depth to the thickness of the workpiece. Less than a full tooth of the blade teeth should be visible below the workpiece.
- Page 8 Safety information TTB911CSW by TITAN Safety warnings >If the blade becomes twisted or misaligned in the cut, the teeth at the back edge of the blade can dig into the top surface of the wood causing the blade to climb out of the kerf and jump back toward the operator.
- Page 9 TTB911CSW by TITAN Safety information >Do not use dull or damaged blades. Unsharpened or improperly set blades produce narrow kerf causing excessive friction, blade binding and kickback. >Blade depth and bevel adjusting locking levers must be tight and secure before making cut. If blade adjustment shifts while cutting, it may cause binding and kickback.
- Page 10 Safety information TTB911CSW by TITAN Safety warnings >Always observe that the lower guard is covering the unprotected, coasting blade will cause the saw to walk backwards, cutting whatever is in its path. Be aware of the time it takes for the blade to stop after switch is released.
- Page 11 TTB911CSW by TITAN Safety information > >Handle saw blades with care. Store them in the original packaging or in special boxes. Wear gloves for handling and to reduce injuries. > blades. >Before use, make sure that the saw blade complies with technical requirements of the power tool and correctly >...
- Page 12 Safety information TTB911CSW by TITAN Safety warnings Vibration and noise reduction To reduce the impact of noise and vibration emission, limit the time of operation, use low-vibration and low-noise operating modes as well as wear personal protective equipment. Take the following points into account to minimise the vibration and noise exposure risks: >Only use the product as intended by its design and these...
- Page 13 TTB911CSW by TITAN Safety information Residual risks Even if you are operating this product in accordance with all the safety requirements, potential risks of injury and damage remain. The following dangers can arise in connection with the structure and design of this product: >Health defects resulting from vibration emission if the...
- Page 14 Safety information TTB911CSW by TITAN The following information applies to professional users only but is good practice for all users: Additional safety warnings for construction dust The updated Control of Substances Hazardous to Health Regulations 1st October 2012 now also targets to reduce the risks associated with silica, wood and gypsum dusts.
- Page 15 TTB911CSW by TITAN Safety information To protect the lung, the COSHH Regulations sets a limit on the amount of these dusts that you can breathe (called a Workplace Exposure Limit or WEL) when averaged over a normal working day. These limits are not a large amount of dust: when compared to a penny it is tiny –...
- Page 16 Safety information TTB911CSW by TITAN Additional safety warnings for construction dust Some examples of these chemicals are: >Lead from lead-based paints. >Crystalline silica from bricks and cement and other masonry products. >Arsenic and chromium from chemically treated timber. Your risk from these exposures varies, depending upon how often you do this type of work.
- Page 17 TTB911CSW by TITAN Safety information Calculating the actual period of the actual period off information. WARNING! The vibration emission value during actual use of the power tool can differ from the declared value depending on the ways in which the...
- Page 18 Safety information TTB911CSW by TITAN Additional safety warnings for construction dust Helping to minimise your vibration exposure risk. ALWAYS use sharp chisels, drills and blades. Maintain this tool in accordance with these instructions and keep well lubricated (where appropriate). Avoid using tools in temperatures of 10 ºC or less. Plan your work schedule to spread any high vibration tool use across a number of days.
- Page 19 TTB911CSW by TITAN Safety information Wear protective gloves. Wear protective, slip- resistant footwear. yyWxx Manufacturing date code; year of manufacturing (20yy) and week of manufacturing (Wxx) (20yy) and week of manufacturing (Wxx) Blade for cutting wood. Switch the product off and disconnect it from the power supply before assembly, cleaning, adjustments, maintenance, storage and transportation.
-
Page 20: Your Product
Your product TTB911CSW by TITAN Your product... - Page 21 TTB911CSW by TITAN Your product 1. Power cord with plug 13. Orientation mark 2. Dust extraction outlet 14. Parallel guide 3. Rear handle Scale* 4. On/off switch 15. Lower guard 5. Upper guard 16. Saw blade 6. Front handle 17. Locking bolt 7.
- Page 22 EQUIPMENT. This can influence other equipment (e.g. blinking of a lamp). If the MAINS-IMPEDANCE Zmax < 0.42 OHM, such disturbances are not expected. (In case of need, you may contact your local supply authority for further information. Rating Label Explanation TTB911CSW = Model Number...
-
Page 23: Before You Start
TTB911CSW by TITAN Before you start Unpacking > > Remove all packing materials and shipping devices, if applicable. > Make sure the delivery contents are complete and free of any damage. If you your dealer. Using an incomplete or damaged product represents a hazard to people and property. - Page 24 Before you start TTB911CSW by TITAN Setup WARNING! Always use the correct saw blade according to the intended use! Observe the technical requirements of this product (see section Saw blades are very sharp and become hot during use! Handle them...
- Page 25 TTB911CSW by TITAN Before you start > Open the lower guard (15) completely by moving the retracting lever (20) forward and hold it in position while placing the saw blade (16) on the spindle. Ensure that the rotational direction indicated on the saw blade (16) is the same as the one shown on the housing (Fig.
- Page 26 Before you start TTB911CSW by TITAN Parallel guide Attach the parallel guide (14) from the right side to perform cuts parallel to the workpiece edges. > knob (10) anticlockwise. > Align the parallel guide (14) to the support and insert it (Fig. 3).
- Page 27 TTB911CSW by TITAN Before you start Connection to power supply > Make sure the on/off switch (4) is in its off position. > Connect the power plug (1) to a suitable socket. WARNING! Check the voltage! The voltage must comply with the information on the rating label! >...
-
Page 28: In More Detail
TTB911CSW by TITAN more detail... Product functions Operation Care and maintenance Troubleshooting Recycling and disposal Guarantee Declarations of conformity... - Page 29 TTB911CSW by TITAN Product functions Product functions Intended use This product is intended for straight cuts in wood and similar material e. g. MDF and chipboard, with the installed blade. The product must not be used for cutting logs. on the workpiece. It may not be used upside down or as stationary product on a work bench.
- Page 30 Product functions TTB911CSW by TITAN Depth adjustment NOTE: The values shown on the depth scale are only valid for cutting 90°/0° cuts! For bevel cuts the cutting angle will be smaller than indicated. Bevel angle adjustment WARNING! Always switch the product off, disconnect it from power supply before making any adjustments! Adjust the cutting angle according to your needs.
- Page 31 TTB911CSW by TITAN Product functions Switching on/off > Press the lock-off button (21) and hold it in position. > Press the on/off switch (4) to switch the product on (Fig. 9). > Release the on/off switch (4) to switch the product off.
- Page 32 Operation TTB911CSW by TITAN General operation > Check the product, its power cord and plug as well as accessories for damage before each use. Do not use the product if it is damaged or shows wear. > > Always hold the product on its main handle and front handle. Keep the main handle and front handle dry to ensure safe support.
- Page 33 TTB911CSW by TITAN Operation > Cut in the direction of the wood grain whenever possible to avoid jamming the saw blade and fraying edges. > Take the cutting edge into consideration when cutting along marked cutting lines. Do not cut directly on the line but next to it (Fig. 11).
- Page 34 Operation TTB911CSW by TITAN Cutting WARNING! during operation! Do not try to make cuts with the product only held by hand! > workpiece. Higher pressure will not increase but lower the performance of the product and leads to uneven results.
- Page 35 TTB911CSW by TITAN Operation Bevel cutting > Adjust the required cutting angle; properly tightened. > Switch the product on and wait until it runs at full speed before placing it on the workpiece. > workpiece and push the product forward at an even speed (Fig. 14).
- Page 36 Care and maintenance TTB911CSW by TITAN The golden rules for care WARNING! Always switch the product off, disconnect it from the power supply and let the product cool down before performing inspection, maintenance and cleaning work! > Keep the product clean. Remove debris from it after each use and before storage.
-
Page 37: Care And Maintenance
TTB911CSW by TITAN Care and maintenance Maintenance Before and after each use, check the product and accessories (or attachments) for wear and damage. If required, exchange them for new ones as described in this instruction manual. Observe the technical requirements. - Page 38 Care and maintenance TTB911CSW by TITAN Repair This product does not contain any parts that can be repaired by the consumer. checked and repaired. Storage > Switch the product off and disconnect it from the power supply. > Clean the product as described above.
-
Page 39: Troubleshooting
TTB911CSW by TITAN Troubleshooting Troubleshooting Therefore check the product using this section. In most cases the problem can be solved quickly. WARNING! Only perform the steps described within these instructions! All further inspection, maintenance and repair work must be performed... -
Page 40: Recycling And Disposal
Recycling and disposal TTB911CSW by TITAN Recycling and disposal The product comes in a package that protects it against damage during shipping. Keep the package until you are sure that all parts have been delivered and the product is function properly. Recycle the package afterwards. -
Page 41: Guarantee
We take special care to select high quality materials and use manufacturing techniques that allow us to create products incorporating design and durability. This product (TITAN TTB911CSW) has a manufacturer’s guarantee of 2 years against manufacturing defects, from the date of purchase (if bought in store) or date of delivery (if bought online), at no additional cost. - Page 42 EC declaration of conformity TTB911CSW by TITAN EC declaration of conformity (EN) EU DECLARATION OF CONFORMITY (FR) DÉCLARATION UE DE CONFORMITÉ (PL) DEKLARACJA ZGODNOŚCI UE (RO) DECLARAȚIA DE CONFORMITATE UE (ES) DECLARACIÓN UE DE CONFORMIDAD (PT) DECLARAÇÃO DE CONFORMIDADE UE Product/ Produit/ Produkt/Produsul/Producto/Produto •...
- Page 43 TTB911CSW by TITAN EC declaration of conformity 2006/42/WE w zmienionej dyrektywie maszynowej 2014/30/UE ze zmianami Dyrektywa Kompatybilność elektromagnetyczna 2011/65/UE ze zmianami Dyrektywa Ograniczenie stosowania niektórych niebezpiecznych substancji w sprzęcie elektrycznym i elektronicznym 2006/42/CE, astfel a fost modificată Directiva privind echipamentele 2014/30/UE, astfel a fost modificată...
- Page 44 EC declaration of conformity TTB911CSW by TITAN EC declaration of conformity (UK) DECLARATION OF CONFORMITY Product 1500W Circular Saw • TTB911CSW • Serial number: 00001 to 999999 • Name and address of the manufacturer or his authorised representative: Kingfisher International Products Limited...
- Page 48 Manufacturer,Fabricant,Producent,Producător,Fabricante: UK Manufacturer: Kingfisher International Products Limited 3 Sheldon Square, London, W2 6PX United Kingdom www.kingfisher.com/products EU Manufacturer: Kingfisher International Products B.V. Rapenburgerstraat 175E 1011 VM Amsterdam The Netherlands www.kingfisher.com/products www.screwfix.com To view instruction manuals online, visit www.screwfix.ie www.kingfisher.com/products www.bricodepot.fr Pour consulter les manuels d’instructions en ligne, rendez-vous sur le site www.kingfisher.com/products www.bricodepot.es...
Need help?
Do you have a question about the TTB911CSW and is the answer not in the manual?
Questions and answers