Table of Contents
Advertisement
Quick Links
Network Camera
Installation Guide
EN
Please be sure to read the "Safety Precautions" section for correct use.
Caution
Request a professional installer for all installation work. Never try to install
the camera yourself. Doing so may result in unforeseen accidents such as
dropping the camera or electric shock.
Φ132 (Φ5.20)
M4
2 - 4.8 x 4.3 (0.19 x 0.17)
120.9 (4.76)
Unit: mm (in.)
Advertisement
Table of Contents
Related Manuals for Canon VB-S32VE
Summary of Contents for Canon VB-S32VE
- Page 1 Network Camera Installation Guide Φ132 (Φ5.20) 2 - 4.8 x 4.3 (0.19 x 0.17) 120.9 (4.76) Unit: mm (in.) Please be sure to read the “Safety Precautions” section for correct use. Caution Request a professional installer for all installation work. Never try to install the camera yourself.
- Page 2 This document has been prepared with the utmost attention to accuracy. If you have any comments, however, please contact a Canon sales representative. Canon shall assume no liability for any outcome of using this product, notwithstanding items listed above. Trademarks •...
-
Page 3: Part Names
Part Names 13 12 11 1. Microphone 2. Camera head 3. Top cover 4. Top cover lock screw 5. Audio output terminal (P. 15) 6. External device I/O terminal (P. 13) 7. 100Base-TX LAN Connector (P. 13) 8. Safety wire attachment 9. -
Page 4: Installing The Camera
Installing the Camera Template... - Page 5 Installing the Camera Dedicated wrench Remove the top cover. If using a memory card, insert at this time. To remove the memory card, push it in all the way until the card slightly pops out and remove. In this document, memory cards that can be used with the camera is referred to as “memory card”.
- Page 6 Installing the Camera Anchor or structure Safety wire M4 (1) Firmly attach the safety wire to the anchor or structure. After attaching the safety wire to the ceiling, secure it to the camera side and fasten the included screw.
- Page 7 Installing the Camera I/O interface cable RJ45 coupler Connect the cables to the camera. For power supply, external device I/O terminals, and audio output terminal, refer to “Connecting the Camera” (P. 13) . Important The camera head will move and make noise when the power is turned on. •...
- Page 8 Installing the Camera Secure the camera to the installation location. Be sure to prepare mounting screws separately. (Nominal diameter: M4, Head Shape: pan, x 2) Install the top cover. Tighten the screws to ensure waterproofness.
- Page 9 Installing the Camera Notes on Outdoor Installation • Wrap insulating tape around each cable connection to insulate. • The camera body complies with dust-resistant/waterproof specification (IP66), however, the cables connecting to external devices are not. When installing in a place where it may be exposed to even a small amount of water, wrap waterproofing tape (included) around the entire cable joint and the end of the insulated and unused cable to ensure waterproofing.
- Page 10 Installing the Camera How to Wrap Waterproofing Tape Refer to the following procedure to wrap the waterproofing tape. 30 mm (1.18 in.) Start wrap position Stretch the tape to double the length 2× Overlap half the width of the tape ½...
- Page 11 Installing the Camera Important • Wrap the tape so that there are no gaps in the tape, and that the tape has not peeled off or ripped. • Take care not to depress the tab on the LAN cable, when wrapping the connection.
- Page 12 Installing the Camera Overlay the end of the roll on the waterproofing tape Pressing the waterproofing tape moderately to make it adhere. Note • If necessary, wrap it with waterproofing tape to reinforce it.
-
Page 13: Connecting The Camera
Connecting the Camera Power Supply For details, refer to “Others” > “Power Supply” (P. 17) . Check with your dealer for more information about PoE devices. Some PoE devices allow power limits for each port, but applying limits may interfere with performance. - Page 14 Connecting the Camera 1k Ω 10k Ω 10k Ω Input terminal 0.1μF Internal Connection Diagram Output terminal ■ External Device Input Terminals The external device input terminal consists of a positive terminal (IN) and negative terminal (GND). Connecting cables to the positive and negative terminals and opening or closing the circuit notifies the Viewer.
- Page 15 Connecting the Camera Audio Output Terminal LINE OUT (monaural output) Connect the camera to a speaker with an amplifier. Audio can be sent to the speaker from the Viewer. • Output terminal: 3.5 mm ( 0.14 in.) mini jack (monaural) •...
- Page 16 Accessories The following dedicated accessories can be purchased separately as necessary. (Some accessories are not available in certain countries or regions.) Pendant Mounting Kit PC30VE-VB Dedicated accessory used to install the camera to the end of pipe that extends from high ceilings, such as in big-box stores.
-
Page 17: Specifications
Specifications For specifications not listed below, refer to Network Camera's "Specifications". ■ Camera 3.5x optical zoom (4x digital zoom) lens with auto focus Lens Angle of View For 16:9 aspect ratios Horizontal: 78.5° (W) – 20.9° (T) Vertical: 40.8° (W) – 11.7° (T) For 4:3 aspect ratios Horizontal: 55.8°... -
Page 18: Safety Precautions
Failure to do so may result in fire or electric shock. • If conditions such as smoke, strange sounds, heat or strange odors are discovered, immediately stop using the camera and contact a Canon's sales representative. Continuing the use of the product may result in fire or electric shock. - Page 19 • Depending on the computer and network environment, high-precision video transmission cannot be guaranteed due to video latency or loss of video. Canon will assume no liability for any accident or damage resulting from use of the camera under the conditions above.
- Page 20 Safety Precautions Important • Installation of a lightning arrester (a surge protection device) is recommended as a measure against failures caused by lightning strikes. • Do not turn the camera rotator by hand. • Do not install the camera on an unstable surface. •...
- Page 21 • Please be advised that Canon shall not be liable in any way in the event of a dispute between any user and any third party concerning the installation of the product or...
- Page 22 © BIE-7315-000 CANON INC. 2022...