Sealey Professional TOOLS SA3702 Quick Start Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according
to these instructions and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL
REQUIREMENTS, WARNINGS, AND CAUTIONS. USE THIS PRODUCT CORRECTLY, AND WITH CARE
FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE
AND/OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY.
1. SAFETY INSTRUCTIONS
3 Keep the inflator clean and in good condition.
3 Keep children and non-essential persons away from the work area.
WARNING! This inflator is capable of producing a high pressure. DO NOT inflate any item beyond its maximum
p
p
specified pressure.
7 DO NOT direct inflation hose connector head at yourself, others or animals.
7 DO NOT leave the inflator operating unattended. Always monitor the inflation pressure.
7 DO NOT yank the hose from an inflation valve.
7 DO NOT get the inflator wet or use in the rain, it is recommended that it is installed under shelter.
7 DO NOT use the inflator for a task it is not designed for.
3 Check exact pressure required for task, refer to tyre/vehicle manufacturer’s instructions.
7 DO NOT exceed recommended tyre pressure.
7 DO NOT operate the inflator when you are tired or under the influence of alcohol, drugs or intoxicating medication.
7 DO NOT operate the inflator if any parts are missing or the inflator is damaged, as this may cause failure and/or personal
injury.
7 DO NOT open the unit.
7 DO NOT drive over hose or hose connector head.
3 Keep hose tidy and restrained with the hook supplied when not in use.
2. INTRODUCTION & SPECIFICATION
Professional wall-mounted forecourt unit with robust aluminium die-cast casing. Simple to use with large 30mm LCD display
and electronic push-button control. Auto start inflation feature with audible and visual end-of-cycle signal. Accurate pressure
delivery reduces tyre wear, extends tyre life, improves fuel economy and increases safety. Supplied with 7.6 metres of
high-pressure hose and twin hold-on connector.
Max. Inflation Pressure: . . . . . . . . . . . . . . . . .10bar (145psi)
Max. Inlet Pressure: . . . . . . . . . . . . . . . . . . . .16bar (232psi)
Accuracy: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .+/-0.5%
3. PREPARING INFLATOR FOR USE
In order to provide a trouble-free operation it is necessary to connect the power supply from the main switchboard with a MAX
3amp fuse/RCB protection device. This unit must be grounded.
The circuit breaker should be marked as the disconnecting device for the equipment.
4. OPERATING INSTRUCTIONS
Please refer to figure 1 (overleaf) when reading the following instructions:
p WARNING! if you are inflating a flat tyre, make sure you press the “FLAT TYRE” button before inflation, this
p
function will use 10 short pulses of air to begin the inflation, this is recommended for tyres with a pressure of 4
psi/0.3 bar or less.
4.1 Ensure the following
4.1.1 Upon start-up, the display automatically shows the software level (e.g P3.4).
4.1.2 That you do not connect the hose to the tyre during start-up.
4.2 Operation
4.2.1 Set required pressure using the +/- buttons.
4.2.2 Connect the hose to the tyre - the filling process will start automatically.
4.2.3 The inflator will sound when desired pressure is reached, also the display will read “END”.
4.2.4 After 90 seconds of being idle the unit will revert to it’s “Default Safe Setting”
4.2.5 To continue at the same pressure start from step 4.2.2, if different pressure is required begin from step 4.2.1.
DIGITAL TYRE INFLATOR
(WALL MOUNTED)
Input: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .230V
Hose Length: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7.6mtr
SA3702
Model:
SA3702 - 1 - 51104