Sealey SA390 Manual

thank you for purchasing a sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
instructions
1. safety
Do not operate unit if damaged during shipping, handling or use.
8
Read and understand all safety warnings and instructions before operating this product. Failure to read and follow all safety warnings
9
may result in serious personnel injury or death. Property damage and/or product damage may also occur if all warnings are not
followed.
Do not expose the product to flammable gases, vapours or fumes
8
Do not store flammable gases in or near this product
8
Never use flammable or toxic solvents to clean the product or any of the unit's parts
9
Never remove or alter any safety warning labels, tags, etc. located or provided with product.
9
Follow all directions for maintenance.
9
The use of other than genuine replacement parts may result in reduced equipment performance. Repairs must be performed by
9
authorised repair personnel, otherwise the warranty will be void.
▲ Danger! This product can be dangerous if used improperly. Children should not be allowed to use this equipment, as incorrect
setting can allow tyre to be over inflated and a subsequent tyre burst/explosion can occur!
Each person who is involved with installation, start-up, maintenance and the operation of the unit must read and understand the
9
complete operating manual.
The Sealey tyre inflators are exclusively approved for the dispensing of air/N2. Each use which doesn't follow this purpose as well as
9
modifications to the product will be deemed to be improper use. The manufacturer is not liable for damages caused by improper use,
the risk lies solely with the user.
Proper use of the product also implies the observance of the manufacturers instructions with regard to installation, start-up, operation
9
and maintenance.
All works concerning installation, start-up, adjustment and maintenance must be made by qualified staff. For the operation of this
9
tyre pressure inflator the local safety and accident prevention rules must be observed in all cases.
High Pressure air is stored within the system.
9
When using N2P mode , locate this system in a well ventilated area. Position the system away from any heat source.
9
Do not exceed the maximum air input pressure.
8
Do not operate this product if tired or under the influence of medication, drugs or alcohol.
8
warning! To avoid the risk of personal injury, especially to the eyes, face or skin Do not direct the air/N2 stream at any person.
‰
2. introDuction
Robust, high reliability and modern design which is space-saving and lightweight. Touch screen technology with human touch recognition
software. Electronic pressure pre-set with additional four button memory function. Three modes, inflate, deflate and over pressure setting
(OPS) – which allows operator to set the machine to automatically seat the bead on new tyres whilst getting on with alternative work. The
inclusion of the nitrogen (N2) purge facility allows the unit to increase the effectiveness of this increasingly popular tyre service. Red flashing
light, flashing screen and audio signal for end of cycle. Auto-start Inflation. Ceramic sensor gives guaranteed accuracy to ± 0.5% of full scale
reading even with hoses up to 50m in length. 21mm Backlit transflective LCD gives a clear easy to read display. Supplied with a wall bracket,
5m hose with new patented design clip-on connector and BS approved 13A plug. 2 year warranty.
3. sPecification
Model no:................................................................... sa390
Accuracy: .................................... ± 0.5% of full scale reading
Inlet Size: .................................................................1/4" BSP
Maximum Air Supply: ....12bar(174psi, 12.2kg/cm², 1200kPa)
Pressure Units: ......................................bar, psi, kg/cm², kPa
Range: ............. 0-12bar(0-174psi, 0-12.2kg/cm², 0-1200kPa)
© Jack Sealey limited
Professional air Qube Digital tyre
inflator with oPs + nitrogen Purge
sa390
Model no:
Original Language Version SA390 Issue 1 02/07/19