Sealey SA38.V2 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT
CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL
INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
Refer to Wear eye
instruction protection
manual
WARNING! Ensure that Health & Safety, local authority and general workshop practice regulations are adhered to when using this

equipment.
Familiarise yourself with the applications, limitations and potential hazards peculiar to the riveter.

WARNING! Disconnect the riveter from the air supply before changing accessories, servicing or performing any maintenance.

Maintain the riveter in good condition (use an authorised service agent).

Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.

Keep the work area clean, uncluttered and ensure that there is adequate lighting.

Keep the riveter clean for best and safest performance.

WARNING! Always wear approved eye or face protection when operating the riveter.

Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.

Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain, and/or tie back, long hair.

Keep the riveter away from your body and at a safe distance from others.

Keep children and unauthorised persons away from the work area.

Secure unstable workpiece with a clamp, vice or other adequate holding device.

Ensure that spent rivet stems are disposed of correctly and do not cause a hazard.

WARNING! Ensure that the correct air pressure is maintained and not exceeded.

Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure that all connections are secure.

 DO NOT use the riveter for any purpose other than that for which it is designed.
 DO NOT operate the riveter if any parts are damaged or missing.
 DO NOT carry the riveter by the hose, or yank the hose from the air supply.
 DO NOT get the riveter wet or use in damp or wet locations or areas where there is condensation.
 DO NOT allow untrained persons to operate the riveter.
 DO NOT point or fire the riveter at people or animals.
 DO NOT operate the riveter when you are tired or under the influence of alcohol, drugs or intoxicating medication.
 DO NOT direct air from the air hose at yourself or others.
When not in use disconnect from the air supply and store in a safe, dry, childproof area.

2. INTRODUCTION
Lightweight yet powerful riveter handles aluminium rivets up to 3/16"(4.8mm). Fast action unit capable of 28-30 rivets a minute. Well balanced,
trigger operated unit suitable for light production work. DO NOT use for steel rivets.
3. SPECIFICATION
Model No:. . . . . . . . . . . . . . . . . . . . . . . . SA38.V2
Nozzle Sizes: . . . . . . 3/32"(2.4mm), 1/8"(3.2mm),
. . . . . . . . . . . . . . . . . 5/32"(4.0mm), 3/16"(4.8mm)
Air Consumption: . . . . . . . . . . . . . . . . . . . . 0.6cfm
Operating Pressure: . . . . . . . . . . . . . . . .60-110psi
Air Inlet: . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/4"BSP
Weight: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.4kg
Noise Power: . . . . . . . . . . . . . . . . . . . . . . . . 88dB
Noise Pressure: . . . . . . . . . . . . . . . . . . . . . . 77dB
Vibration: . . . . . . . . . . . . . . . . . . . . . . . . . . 0.2m/s²
Uncertainty: . . . . . . . . . . . . . . . . . . . . . . . . 0.1m/s²
4. AIR SUPPLY
The recommended air system is shown in fig.1.
4.1. Ensure that the trigger is in the "Off" position before connecting to the air supply.
4.2. Ensure that the air pressure is set correctly (60-110psi).
WARNING! Ensure that the air supply is clean and does not exceed 110psi. Too high an air pressure and/or unclean air will shorten the
p
life of the riveter due to accelerated wear, and may cause damage and/or personal injury.
4.3. Drain the compressor air tank daily. Water in the air line will damage the riveter.
4.4. Clean the compressor air inlet filter screen weekly.
© Jack Sealey Limited
INSTRUCTIONS FOR:
AIR RIVETER
MODEL No:
Wear Wear
ear protective
protection gloves
Original Language Version
SA38.V2
SA38.V2 Issue: 2 - 07/11/14