DeWalt DWDCF883B Instruction Manual
  1. Manuals
  2. Brands
  3. DeWalt Manuals
  4. Impact Driver
  5. DWDCF883B
  6. Instruction manual

DeWalt DWDCF883B Instruction Manual

3/8" (9.5 mm) 20v max* cordless impact wrench
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
INSTRUCTION MANUAL
DCF883
3/8" (9.5 mm) 20V Max* Cordless Impact Wrench

Advertisement

Table of Contents
loading

Related Manuals for DeWalt DWDCF883B

Summary of Contents for DeWalt DWDCF883B

  • Page 1 INSTRUCTION MANUAL DCF883 3/8" (9.5 mm) 20V Max* Cordless Impact Wrench...

  • Page 2: Defi Nitions: Safety Guidelines

    1) WORK AREA SAFETY Defi nitions: Safety Guidelines a) Keep work area clean and well lit. Cluttered or dark areas invite accidents. The definitions below describe the level of severity for each b) Do not operate power tools in explosive atmospheres, signal word.

  • Page 3: Personal Safety

    3) PERSONAL SAFETY 4) POWER TOOL USE AND CARE a) Stay alert, watch what you are doing and use common a) Do not force the power tool. Use the correct power tool sense when operating a power tool. Do not use a power for your application.

  • Page 4: Additional Specific Safety Rules

    battery pack may create a risk of fire when used with another • Bits, sockets and tools get hot during operation. Wear gloves battery pack. when touching them. b) Use power tools only with specifically designated battery • Air vents often cover moving parts and should be avoided. packs.

  • Page 5: Important Safety Instructions For All Battery Packs

    and water. Allowing dust to get into your mouth, eyes, or lay on Important Safety Instructions for All the skin may promote absorption of harmful chemicals. Battery Packs WARNING: Use of this tool can generate and/or disburse dust, When ordering replacement battery packs, be sure to include the which may cause serious and permanent respiratory or other injury.

  • Page 6: Specific Safety Instructions For Lithium Ion (Li-Ion)

    pack. Do not use a battery pack or charger that has received a sharp • Contents of opened battery cells may cause respiratory blow, been dropped, run over or damaged in any way (e.g., pierced irritation. Provide fresh air. If symptoms persist, seek medical with a nail, hit with a hammer, stepped on).
  • Page 7 • Before using the charger, read all instructions and cautionary • When operating a charger outdoors, always provide a dry markings on the charger, battery pack and product using the location and use an extension cord suitable for outdoor use. battery pack.

  • Page 8: Charge Indicators

    • Do not operate the charger if it has received a sharp blow, Indicator Light Operation been dropped or otherwise damaged in any way. Take it to an authorized service center. PACK CHARGING • Do not disassemble the charger; take it to an authorized service center when service or repair is required.

  • Page 9: Important Charging Notes

    LEAVING THE BATTERY PACK IN THE CHARGER throughout the entire charging cycle and will not return to maximum charge rate even if the battery pack warms. The charger and battery pack can be left connected with the charge indicator showing Pack Charged. 4.

  • Page 10: Storage Recommendations

    Storage Recommendations FIG. 2 DCF883 1. The best storage place is one that is cool and dry, away from direct sunlight and excess heat or cold. 2. For long storage, it is recommended to store a fully charged battery pack in a cool dry place out of the charger for optimal results.

  • Page 11: Operation

    IMPORTANT: When attaching or replacing the belt hook, use only the FUEL GAUGE BATTERY PACKS (FIG. 4) screw (I) that is provided. Be sure to securely tighten the screw. Some D WALT battery packs include a fuel gauge which consists of three green LED lights that indicate the level of charge remaining in The belt hook (H) can be be attached to either side of the tool using the battery pack.
  • Page 12 NOTE: Continuous use in variable speed range is not recommended. FIG. 5 FIG. 6 It may damage the switch and should be avoided. Forward/Reverse Control Button (Fig. 2) A forward/reverse control button (B) determines the direction of the tool and also serves as a lock-off button. To select forward rotation, release the trigger switch and depress the forward/reverse control button on the right side of the tool.

  • Page 13: Maintenance

    Usage MAINTENANCE Your impact tool can generate the following maximum torque: WARNING: To reduce the risk of serious personal injury, place the forward/reverse button in the lock-off position or turn tool Cat # Ft.-Lbs. In.-Lbs. off and disconnect battery pack before making any adjustments or removing/installing attachments or accessories.
  • Page 14 WARNING: To reduce the risk of injury, use only D WALT impact- ready accessories. CAUTION: Use only impact sockets. Non-impact sockets may break and cause a hazardous condition. Inspect sock et prior to use to ensure that it con tains no cracks. Repairs The charger and battery pack are not serviceable.

This manual is also suitable for:

Dcf883

Table of Contents