Advertisement
▲
DANGER! DO NOT wear this respirator system to enter areas where:
1. Atmospheres are oxygen defi cient.
2. Contaminant concentrations are unknown.
3. Contaminant concentrations are Immediately Dangerous to Life or Health.
4. Contaminant concentrations exceed the maximum use concentration determined using the assigned Protection Factor for the
specifi c respirator system.
If ventilation is poor, wear an approved air-supplied respirator.
Work in confi ned space only if it is well ventilated, or while wearing an air-supplied respirator. Always have a trained watch-
person nearby. Ensure the breathing air is safe.
Read and follow these instructions and the safety labels carefully.
The powered air purifying respirator (PAPR) helps protect the user from specifi c airborne contaminants but must be used correctly
to be fully eff ective. Have an industrial hygienist test the air in your facility to ensure the PAPR provides adequate protection from
contaminants in your environment. If you have questions about the respirator, see equipment warning label and consult your Safety
Director and a certifi ed Industrial Hygienist.
Follow all applicable EN/ANSI/CSA/AS&NZS, and other regulatory guidelines pertaining to the use of respirators.
DO NOT use the powered air purifying respirator where there is danger of fi re or explosion.
DO NOT use the powered air purifying respirator in windy conditions or negative pressure inside the hood may draw in
contaminants from the outside air.
The powered air purifying respirator does not supply oxygen. Use the respirator only in atmospheres for which it is EN/ANSI/CSA/
AS&NZS approved.
DO NOT use the respirator where oxygen levels are 19.5% or lower, where contaminant levels are unknown or are immediately
dangerous to life or health, or where the contaminant levels exceed the respirator specifi cations.
DO NOT enter a hazardous area until you are sure the respirator equipment is correctly assembled, working properly, and properly
worn.
Before each use, inspect the respirator equipment for damage and verify it operates properly.
Before using the respirator, test air fl ow to verify it is providing an adequate volume of air.
DO NOT use the powered air purifying respirator without all fi lter components or with the blower turned off , as hazardous levels of
oxygen and carbon dioxide may accumulate in helmet.
Always wear the powered air purifying respirator when entering a contaminated area.
DO NOT remove the respirator until outside the contaminated area.
Dangerous contaminants may not smell or be visible. Leave the area immediately if you notice the following:
- Breathing becomes diffi cult.
- You experience dizziness, impaired vision, or eye, nose, or mouth irritation.
- The powered air purifying respirator alarm sounds.
- The equipment is damaged.
- Air fl ow decreases or stops.
- If you think the equipment is not supplying adequate protection.
DO NOT remove the equipment until you are in a safe area.
DO NOT repair, modify, or disassemble the powered air purifying respirator or use with parts or accessories not supplied by the
manufacturer. Use only those components that are part of the approved assembly.
Replace damaged or clogged fi lters.
WARNING! The particle fi lter CAN NOT be cleaned.
DO NOT wash or reuse fi lters.
DO NOT clean fi lters by tapping or with compressed air as this will destroy the fi lters, the equipment will not give the expected
protection and the warranty will be invalidated.
Dispose of used fi lter elements according to local requirements.
The powered air purifying respirator must be used with the face shield, face hood, and fi lters recommended by the manufacturer to
provide a respirator system. See the label on the blower for information on the required equipment.
DO NOT use the powered air purifying respirator belt or shoulder straps (if equipped) as a safety harness.
2. INTRODUCTION
PAPR (Powered Air Purifying Respirator) system with deluxe safety face shield. Lithium battery powered respirator unit provides the user
a constant fi ltered stream of air to their head and face for up to approximately 8 hours. The fi lter assembly, consisting of a foam pre-fi lter &
HEPA fi lter, is designed to reduce or remove dust and particles but not vapours and gases. The kit meets performance class TH2 according
to EN 12941:1998/A2:2008. Adjustable airfl ow settings of 150-180L/min. Features an audible alarm to alert user of low battery/low airfl ow.
Polycarbonate visor for increased protection, stability, and durability. Ratchet adjustable headband with front and back padding for extra
comfort. Suitable for use with standard glasses. Face shield conforms to BS EN 166, Optical Class 1, Impact Grade F.
3. SPECIFICATION
Model No: ..........................................................SSP80PAPR
PAPR Air fl ow settings: .................................... 150/180 L/min
Operating time: ..............................Low speed: 6-8hr approx.
...................................................... High speed: 4-6hr approx.
PAPR Lithium battery charging time: .................... 3hr approx.
Operating temperature: ........................................ -5° to 55°C
Storage temperature: ..........................................-10° to 50°C
PAPR Filter classifi cation: ................................... TH2 P R SL
© Jack Sealey Limited
Original Language Version
SSP80PAPR Issue 1 11/08/21
Advertisement
