DeWalt DWE575 Manual
  1. Manuals
  2. Brands
  3. DeWalt Manuals
  4. Saw
  5. DWE575
  6. Manual

DeWalt DWE575 Manual

Hide thumbs Also See for DWE575:
Table of Contents

Advertisement

Quick Links

Download this manual
DWE575

Advertisement

Table of Contents
loading

Related Manuals for DeWalt DWE575

Summary of Contents for DeWalt DWE575

  • Page 1 DWE575...
  • Page 2 English (original instructions) Copyright D WALT...
  • Page 3 Fig. A...
  • Page 4 Fig. C Fig. B Fig. D Fig. E Fig. G Fig. F...
  • Page 5 Fig. H Fig. I Fig. J...
  • Page 6 Fig. K Fig. L Fig. M Fig. N 45° 0°...
  • Page 7 Fig. O Fig. P Fig. R Fig. Q...
  • Page 8 Fig. S Fig. T Fig. U Fig. V...

  • Page 9: Definitions: Safety Guidelines

    English 184 mm CIRCULAR SAW DWE575 Congratulations! WARNING: To reduce the risk of injury, read the instruction manual. You have chosen a D WALT tool. Years of experience, thorough product development and innovation make D WALT one of the Definitions: Safety Guidelines most reliable partners for professional power tool users.

  • Page 10: Personal Safety

    English 4) Power Tool Use and Care b ) Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and a ) Do not force the power tool. Use the correct power refrigerators. There is an increased risk of electric shock if tool for your application.

  • Page 11: Further Safety Instructions For All Saws

    English d ) Never hold the workpiece in your hands or across it may walk up or kickback from the workpiece as the saw your leg while cutting. Secure the workpiece to a is restarted. stable platform. It is important to support the work d ) Support large panels to minimise the risk of blade properly to minimize body exposure, blade binding, pinching and kickback.

  • Page 12: Using An Extension Cable

    English and alignment can make the riving knife ineffective in Mains Plug Replacement preventing kickback. (U.K. & Ireland Only) c ) Always use the riving knife except when plunge If a new mains plug needs to be fitted: cutting. Riving knife must be replaced after plunge •...

  • Page 13: Intended Use

    English Main handle 2. Place outer clamp washer   15  on saw spindle with the beveled edge facing out. Make sure the 30 mm diameter on Blade lock the blade side of the clamp fits into the 30 mm hole in the End cap saw blade to ensure centering of the blade.
  • Page 14 English Checking the Lower Guard (Fig. A) The saw can lift partially out of the cut increasing the chance of blade twist. 1. Turn tool off and disconnect from power supply. 2. iMPROPER DEPTh OF CUT sETTing On sAW 2. Rotate the lower guard lever (Fig. A,  ) from the fully  12 ...

  • Page 15: Operation

    • Do not use excessively worn saw blades. The DWE575 is equipped with a bevel detent feature. As you tilt the base plate you will hear a click and feel the base plate OPERATION stop at both 22.5 and 45 degrees. If either of these is the desired Instructions for Use angle, retighten the lever ...

  • Page 16: Maintenance

    English To avoid kickback, ALWAYS support board or panel NEAR the A pocket cut is one that is made in a floor, wall or other cut, (Fig. O and Q) . DON’T support board or panel away from flat surface. the cut (Fig. P and R) . When operating the saw, keep the cord 1.

  • Page 17: Protecting The Environment

    English the saw through the cut, when the motor is straining, or when excessive heat is built up in the blade. It is a good practice to keep extra blades on hand so that sharp blades are available for Cleaning immediate use.
  • Page 20 Belgique et WALT - Belgium BVBA Tel: NL 32 15 47 37 63 www.dewalt.be luxembourg België en luxemburg enduser.BE@sBDinc.com Egide Walschaertsstraat 16 Tel: FR 32 15 47 37 64 2800 Mechelen Fax: 32 15 47 37 99 Danmark WALT (Stanley Black&Decker AS)

Table of Contents