Related Manuals for Nokia Flexi Zone Micro High Power 2x20 W BTS
Summary of Contents for Nokia Flexi Zone Micro High Power 2x20 W BTS
- Page 1 Nokia Networks Installing and Cabling Flexi Zone Micro High Power 2x20 W BTS DN09229011 Issue 02 Approval Date yyyy-mm-dd ...
- Page 2 (“Agreement”) under which this document is distributed. No part of this document may be used, copied, reproduced, modified or transmitted in any form or means without the prior written permission of Nokia Solutions and Networks. If you have not entered into an Agreement applicable to the Product, or if that Agreement has expired or has been terminated, You may not use this document in any manner and You...
- Page 3 Installing and Cabling Flexi Zone Micro High Power 2x20 W BTS Table of Contents This document has 67 pages Summary of changes..............8 Installing Flexi Zone Micro BTS............. 9 Installing Flexi Zone Micro BTS (FWHR) on a wall......9 Installing Flexi Zone Micro BTS (FWHR) on a vertical pole..17 Installing Flexi Zone Micro BTS (FWHR) on a horizontal pole..24 Cabling Flexi Zone Micro BTS............. 32 Cabling the copper interface............34 Cabling the optical interface............37 Flexi Zone Micro BTS (FWHR) interfaces........41 Installing antennas............... 43 Installing omnidirectional antennas..........43 Installing third-party antennas............43 Considerations for remotely connecting RF antennas....44 Installing Bluetooth antenna............45 3.4.1 Bluetooth antenna................ 45 Installing GPS antenna..............
- Page 4 Installing and Cabling Flexi Zone Micro High Power 2x20 W BTS 4.4.4.2 Antenna system noise figure............57 4.4.4.3 GPS mounting brackets............... 58 Contents of Flexi Zone Micro BTS delivery........59 Flexi Zone Micro BTS installation tools and equipment....60 Safety for Public and Workers............61 Installing base stations to ensure public safety......61 Installing base stations to ensure installer safety......61 Flexi Zone Micro BTS (FWHR) United States FCC Part 15 compliance................... 63 Flexi Zone Micro BTS (FWHR) Industry Canada IC RSS-GEN compliance................... 64 Flexi Zone Micro Bluetooth Modular Approval......66 EU RoHS statement..............67 DN09229011 Issue: 02...
-
Page 5: Table Of Contents
Installing and Cabling Flexi Zone Micro High Power 2x20 W BTS List of Figures Figure 1 Flexi Zone Micro BTS (FWHR) interface panel........9 Figure 2 Flexi Zone Micro BTS clearances............11 Figure 3 Disassembling the mounting bracket..........12 Figure 4 Fixing the interface bracket..............12 Figure 5 Static mounting bracket keyholes............13 Figure 6 Drilling the holes................. 13 Figure 7 Installing the static mounting bracket on the wall....... 14 Figure 8 Rubber plug location................15 Figure 9 Correct bracket alignment..............16 Figure 10 Installing the BTS on a wall..............16 Figure 11 Flexi Zone Micro BTS (FWHR) interface panel........17 Figure 12 Flexi Zone Micro BTS clearances............19 Figure 13 Disassembling the mounting bracket..........20 Figure 14 Fixing the interface bracket..............20 Figure 15 Threading the straining straps............ - Page 6 Installing and Cabling Flexi Zone Micro High Power 2x20 W BTS Figure 39 Connecting the optical cable.............. 39 Figure 40 Fastening the fiber extender tube............39 Figure 41 Fastening the grommet housing into the fiber extender tube..... 40 Figure 42 Pushing the grommet into the grommet housing........40 Figure 43 Fastening the nut to the grommet housing......... 41 Figure 44 Flexi Zone Micro BTS (FWHR) interfaces - bottom view....42 Figure 45 Flexi Zone Micro BTS (FWHR) interfaces - top view......42 Figure 46 Bluetooth antenna................46 Figure 47 FAWD....................47 Figure 48 FAWD label..................47 Figure 49 Cell site GPS satellite visibility............49 Figure 50 Maximizing GPS antenna visibility............50 Figure 51 GPS antenna placement considerations..........51 Figure 52 Maximum GPS receiver interference power level vs. frequency..52 Figure 53 Typical RF GPS antenna configuration diagram........ 53 Figure 54 Remote RF GPS antenna configuration diagram.......
- Page 7 Installing and Cabling Flexi Zone Micro High Power 2x20 W BTS List of Tables Table 1 Releases covered by the document............. 8 Table 2 Flexi Zone Micro BTS (FWHR) maintenance clearances....10 Table 3 Flexi Zone Micro BTS (FWHR) maintenance clearances....18 Table 4 Flexi Zone Micro BTS (FWHR) maintenance clearances....25 Table 5 Flexi Zone Micro BTS (FWHR) interfaces.......... 41 Table 6 Properties of the Bluetooth antenna........... 45 Table 7 Properties of GPS antenna (FAWD) (472932A)......... 46 Table 8 Recommended GPS antenna specifications........54 Table 9 Antenna cable loss and bend radius data.......... 55 Table 10 Flexi Zone Micro BTS delivery contents..........59 Table 11 FMWA Flexi Zone Wall and Pole Mounting Bracket (472858A) delivery contents....................59 Table 12 Installation tools..................60 Table 13 Required Compliance Boundaries (CB) by band .......61 Issue: 02 DN09229011...
- Page 8 Summary of changes Installing and Cabling Flexi Zone Micro High Power 2x20 W BTS Summary of changes Changes between document issues are cumulative. Therefore, the latest document issue contains all changes made to previous issues. This document is common for all TDD-LTE releases. You may find here information about solutions that are not available or supported in a specific SW release or RAT. For features supported in your SW release, see respective feature documentation chapter in the system library. Table 1 Releases covered by the document Product Release TD LTE TD-LTE15A, TD-LTE16 This document contains instructions that are specific for Flexi Zone Micro BTS (FWHR). Changes between issues 01 (2015-12-22) and 02 (yyyy-mm-dd) The following sections have been added: Installing base stations to ensure installer safety • Flexi Zone Micro BTS (FWHR) United States FCC Part 15 compliance • Flexi Zone Micro BTS (FWHR) Industry Canada IC RSS-GEN compliance • Flexi Zone Micro Bluetooth Modular Approval • EU RoHS statement • Issue 01 This is the first issue of the document.
-
Page 9: Figure 1 Flexi Zone Micro Bts (Fwhr) Interface Panel
Installing and Cabling Flexi Zone Micro High Power Installing Flexi Zone Micro BTS 2x20 W BTS 1 Installing Flexi Zone Micro BTS 1.1 Installing Flexi Zone Micro BTS (FWHR) on a wall The procedure describes the installation on a wall that is specific for FWHR. Purpose Use the Flexi Zone Wall and Pole Mounting Bracket (FMWA) (472858A) to install Flexi Zone Micro BTS (FWHR) on a wall. Before you start CAUTION! Risk of personal injury. Ensure that the wall installation surface and selected fasteners can sustain the device under required circumstances. Evaluation of the wall structure and fastening hardware type should be done by a structural engineer. NOTICE: Flexi Zone Micro BTS equipment must be installed by trained and qualified service personnel in accordance with all local codes and requirements. NOTICE: Flexi Zone Micro BTS equipment is intended for installation in a restricted access location or equivalent. NOTICE: The BTS interface panel should always face the ground. Any other installation position might cause overheating and possible damage to the BTS. - Page 10 Installing Flexi Zone Micro BTS Installing and Cabling Flexi Zone Micro High Power 2x20 W BTS Avoid mounting the BTS such that the antennas are blocked by other structures such • as walls. A direct line of sight to the area to be covered will provide the best performance. Keep other metallic mounting features as far away from all antennas as possible. • Keep cables routed and secured away from the LTE and Bluetooth antennas. • Remotely locating the Bluetooth antenna is not allowed. • Since only remotely connected antennas are supported, external lightning surge • protection must be added. For more information on remotely mounting antennas, see section Installing antennas. If side clearance is less than screw driver length, the grounding cable needs to be pre- installed. The minimum and recommended maintenance clearances are shown in Table 2: Flexi Zone Micro BTS (FWHR) maintenance clearances. Table 2 Flexi Zone Micro BTS (FWHR) maintenance clearances BTS side Minimum clearances Recommended clearances Front 50 mm (1.97 in) 500 mm (19.68 in) Rear 35 mm (1.38 in ) 35 mm (1.38 in ) 100 mm (3.94 in) Height of the unit + 10 mm (0.39 in) Bottom 100 mm (3.94 in) 300 mm (11.81 in) Left...
-
Page 11: Figure 2 Flexi Zone Micro Bts Clearances
Installing and Cabling Flexi Zone Micro High Power Installing Flexi Zone Micro BTS 2x20 W BTS Figure 2 Flexi Zone Micro BTS clearances Procedure Disassemble the mounting bracket. The mounting bracket consists of two elements: the interface bracket and static bracket. Loosen the two thumb screws (M6), slide up the interface bracket and put aside the static bracket. Note that thumb screws (M6) are integral parts of the interface bracket. Issue: 02 DN09229011... -
Page 12: Figure 3 Disassembling The Mounting Bracket
Installing Flexi Zone Micro BTS Installing and Cabling Flexi Zone Micro High Power 2x20 W BTS Figure 3 Disassembling the mounting bracket Interfacebracket Staticbracket Fix the interface bracket to the Flexi Zone Micro BTS using two M6 cap screws and washers included with the mounting bracket. Tighten the screws to 5.1 Nm (3.8 ft-lb). Figure 4 Fixing the interface bracket DN09229011 Issue: 02... -
Page 13: Figure 5 Static Mounting Bracket Keyholes
Installing and Cabling Flexi Zone Micro High Power Installing Flexi Zone Micro BTS 2x20 W BTS Mark the mounting screw locations on the wall and drill the holes for the screws. Tip: Use the static mounting bracket keyholes as a template. Figure 5 Static mounting bracket keyholes Keyholesfor drilltemplate Figure 6 Drilling the holes (4.53in.) Fix the mounting bolts to the wall, and install the static mounting bracket on the wall. -
Page 14: Figure 7 Installing The Static Mounting Bracket On The Wall
Installing Flexi Zone Micro BTS Installing and Cabling Flexi Zone Micro High Power 2x20 W BTS Figure 7 Installing the static mounting bracket on the wall DN09229011 Issue: 02... -
Page 15: Figure 8 Rubber Plug Location
Installing and Cabling Flexi Zone Micro High Power Installing Flexi Zone Micro BTS 2x20 W BTS Tighten the bracket’s fastener according to the manufacturer’s instructions. Install the BTS to the static mounting bracket. NOTICE: If you lift the unit with a rope, use an M6 size eyebolt with a M6 x 1.0 thread. The eyebolt should be fixed to the top of the BTS, in place of the rubber plug. The eyebolt should be removed and replaced with the rubber plug after installing the BTS. The eyebolt is not part of the delivery and must be ordered separately. Figure 8 Rubber plug location a) Position the BTS with the interface bracket aligned directly above the static mounting bracket. b) Slide down the BTS until it is fully located and seated onto the static bracket. c) Hand start the thumb screws (M6) to secure BTS to static bracket. d) Torque all M6 screws to 5.1 Nm (3.8 ft-lb). Issue: 02 DN09229011... -
Page 16: Figure 9 Correct Bracket Alignment
Installing Flexi Zone Micro BTS Installing and Cabling Flexi Zone Micro High Power 2x20 W BTS Note: Before tightening the screws make sure that: the static mounting bracket is securely captivated in the interface bracket's slot. • tabs on the interface bracket are captivated by the back surface of the static • mounting bracket. Figure 9 Correct bracket alignment Tabson interfacebracket Tabon staticbracket Slotininterfacebracket Figure 10 Installing the BTS on a wall DN09229011 Issue: 02... -
Page 17: Figure 11 Flexi Zone Micro Bts (Fwhr) Interface Panel
Installing and Cabling Flexi Zone Micro High Power Installing Flexi Zone Micro BTS 2x20 W BTS 1.2 Installing Flexi Zone Micro BTS (FWHR) on a vertical pole The procedure describes the installation on a vertical pole that is specific for FWHR. Purpose Use the Flexi Zone Wall and Pole Mounting Bracket (FMWA) (472858A) and band straps to install Flexi Zone Micro BTS on a pole. The band straps depend on the chosen pole diameter. The width of the band straps should be less than ¾" to properly fit into the slots of the mounting bracket. Before you start CAUTION! Risk of personal injury. Ensure that the selected band straps can sustain the device under required circumstances. The selected band straps should be rated for outdoor use and be capable of securing the BTS weight. A certified structural engineer should inspect and approve the mounting pole and hardware prior to installation. NOTICE: Flexi Zone Micro BTS equipment must be installed by trained and qualified service personnel in accordance with all local codes and requirements. NOTICE: Flexi Zone Micro BTS equipment is intended for installation in a restricted access location or equivalent. NOTICE: The BTS interface panel should always face the ground. Any other installation position might cause overheating and possible damage to the BTS. - Page 18 Installing Flexi Zone Micro BTS Installing and Cabling Flexi Zone Micro High Power 2x20 W BTS Note: The band straps are not part of the delivery and must be ordered separately. When selecting a location to mount the BTS, keep in mind the following: Avoid mounting the BTS such that the antennas are blocked by other structures such • as walls. A direct line of sight to the area to be covered will provide the best performance. Keep other metallic mounting features as far away from all antennas as possible. • Keep cables routed and secured away from the LTE and Bluetooth antennas. • Remotely locating the Bluetooth antenna is not allowed. • Since only remotely connected antennas are supported, external lightning surge • protection must be added. For more information on remotely mounting antennas, see section Installing antennas. If side clearance is less than screw driver length, the grounding cable needs to be pre- installed. The minimum and recommended maintenance clearances are shown in Table 2: Flexi Zone Micro BTS (FWHR) maintenance clearances. Table 3 Flexi Zone Micro BTS (FWHR) maintenance clearances BTS side Minimum clearances Recommended clearances Front 50 mm (1.97 in) 500 mm (19.68 in) Rear 35 mm (1.38 in ) 35 mm (1.38 in ) 100 mm (3.94 in) Height of the unit + 10 mm (0.39 in) Bottom...
-
Page 19: Figure 12 Flexi Zone Micro Bts Clearances
Installing and Cabling Flexi Zone Micro High Power Installing Flexi Zone Micro BTS 2x20 W BTS Figure 12 Flexi Zone Micro BTS clearances Procedure Disassemble the mounting bracket. The mounting bracket consists of two elements: the interface bracket and static bracket. Loosen the two thumb screws (M6), slide up the interface bracket and put aside the static bracket. Note that thumb screws (M6) are integral parts of the interface bracket. Issue: 02 DN09229011... -
Page 20: Figure 13 Disassembling The Mounting Bracket
Installing Flexi Zone Micro BTS Installing and Cabling Flexi Zone Micro High Power 2x20 W BTS Figure 13 Disassembling the mounting bracket Interfacebracket Staticbracket Fix the interface bracket to the Flexi Zone Micro BTS using two M6 cap screws and washers included with the mounting bracket. Tighten the screws to 5.1 Nm (3.8 ft-lb). Figure 14 Fixing the interface bracket DN09229011 Issue: 02... -
Page 21: Figure 15 Threading The Straining Straps
Installing and Cabling Flexi Zone Micro High Power Installing Flexi Zone Micro BTS 2x20 W BTS Thread the straining straps to the static mounting bracket. Figure 15 Threading the straining straps Install the static mounting bracket to the pole with the straining straps. Note: The straps should be tightened and secured according to the strap manufacturer’s instructions and the bracket should be secure and immovable. Figure 16 Installing the installation plate to the pole Issue: 02 DN09229011... -
Page 22: Figure 17 Rubber Plug Location
Installing Flexi Zone Micro BTS Installing and Cabling Flexi Zone Micro High Power 2x20 W BTS Tighten the straining straps around the pole. Install the BTS to the static mounting bracket. NOTICE: If you lift the unit with a rope, use an M6 size eyebolt with a M6 x 1.0 thread. The eyebolt should be fixed to the top of the BTS, in place of the rubber plug. The eyebolt should be removed and replaced with the rubber plug after installing the BTS. The eyebolt is not part of the delivery and must be ordered separately. Figure 17 Rubber plug location a) Position the BTS with the interface bracket aligned directly above the static mounting bracket. b) Slide down the BTS until it is fully located and seated onto the static bracket. c) Hand start the thumb screws (M6) to secure the BTS to the static bracket. d) Torque all M6 screws to 5.1 Nm (3.8 ft-lb). DN09229011 Issue: 02... -
Page 23: Figure 18 Correct Bracket Alignment
Installing and Cabling Flexi Zone Micro High Power Installing Flexi Zone Micro BTS 2x20 W BTS Note: Before tightening the screws make sure that: the static mounting bracket is securely captivated in the slot in the interface bracket. • tabs on the interface bracket are captivated by the back surface of the static • mounting bracket. Figure 18 Correct bracket alignment Tabson interfacebracket Tabon staticbracket Slotininterfacebracket Figure 19 Installing the BTS on a vertical pole Issue: 02 DN09229011... -
Page 24: Figure 20 Flexi Zone Micro Bts (Fwhr) Interface Panel
Installing Flexi Zone Micro BTS Installing and Cabling Flexi Zone Micro High Power 2x20 W BTS 1.3 Installing Flexi Zone Micro BTS (FWHR) on a horizontal pole The procedure describes the installation on a horizontal pole that is specific for FWHR. Purpose Use the Flexi Zone Wall and Pole Mounting Bracket (FMWA) (472858A) and band straps to install Flexi Zone Micro BTS on a pole. The band straps depend on the chosen pole diameter. The width of the band straps should be less than ¾" to properly fit into the slots of the mounting bracket. Before you start CAUTION! Risk of personal injury. Ensure that the selected band straps can sustain the device under required circumstances. The selected band straps should be rated for outdoor use and be capable of securing the BTS weight. A certified structural engineer should inspect and approve the mounting pole and hardware prior to installation. NOTICE: Flexi Zone Micro BTS equipment must be installed by trained and qualified service personnel in accordance with all local codes and requirements. NOTICE: Flexi Zone Micro BTS equipment is intended for installation in a restricted access location or equivalent. NOTICE: The BTS interface panel should always face the ground. Any other installation position might cause overheating and possible damage to the BTS. - Page 25 Installing and Cabling Flexi Zone Micro High Power Installing Flexi Zone Micro BTS 2x20 W BTS Note: The band straps are not part of the delivery and must be ordered separately. When selecting a location to mount the BTS, keep in mind the following: Avoid mounting the BTS such that the antennas are blocked by other structures such • as walls. A direct line of sight to the area to be covered will provide the best performance. Keep other metallic mounting features as far away from all antennas as possible. • Keep cables routed and secured away from the LTE and Bluetooth antennas. • Remotely locating the Bluetooth antenna is not allowed. • Since only remotely connected antennas are supported, external lightning surge • protection must be added. For more information on remotely mounting antennas, see section Installing antennas. If side clearance is less than screw driver length, the grounding cable needs to be pre- installed. The minimum and recommended maintenance clearances are shown in Table 2: Flexi Zone Micro BTS (FWHR) maintenance clearances. Table 4 Flexi Zone Micro BTS (FWHR) maintenance clearances BTS side Minimum clearances Recommended clearances Front 50 mm (1.97 in) 500 mm (19.68 in) Rear 35 mm (1.38 in ) 35 mm (1.38 in ) 100 mm (3.94 in) Height of the unit + 10 mm (0.39 in) Bottom...
-
Page 26: Figure 21 Flexi Zone Micro Bts Clearances
Installing Flexi Zone Micro BTS Installing and Cabling Flexi Zone Micro High Power 2x20 W BTS Figure 21 Flexi Zone Micro BTS clearances Procedure Disassemble the mounting bracket. The mounting bracket consists of two elements: the interface bracket and static bracket. Loosen the two thumb screws (M6), slide up the interface bracket and put aside the static bracket. Note that thumb screws (M6) are integral parts of the interface bracket. DN09229011 Issue: 02... -
Page 27: Figure 22 Disassembling The Mounting Bracket
Installing and Cabling Flexi Zone Micro High Power Installing Flexi Zone Micro BTS 2x20 W BTS Figure 22 Disassembling the mounting bracket Interfacebracket Staticbracket Fix the interface bracket to the Flexi Zone Micro BTS using two M6 cap screws and washers included with the mounting bracket. Tighten the screws to 5.1 Nm (3.8 ft-lb). Issue: 02 DN09229011... -
Page 28: Figure 23 Fixing The Interface Bracket
Installing Flexi Zone Micro BTS Installing and Cabling Flexi Zone Micro High Power 2x20 W BTS Figure 23 Fixing the interface bracket Thread the straining straps to the static mounting bracket. Figure 24 Threading the straining straps DN09229011 Issue: 02... -
Page 29: Figure 25 Installing The Static Mounting Bracket On The Pole
Installing and Cabling Flexi Zone Micro High Power Installing Flexi Zone Micro BTS 2x20 W BTS Install the static mounting bracket on the pole with the straining straps. Note: The straps should be tightened and secured according to the strap manufacturer’s instructions and the bracket should be secure and immovable. Figure 25 Installing the static mounting bracket on the pole Issue: 02 DN09229011...