Operation - DeWalt DW682 Original Instructions Manual

EngLIsh
2. Set the height adjuster
90 °, the scale under the locking knob reads the distance
between the centre of cutter and the surface of the fence.
3. Tighten the locking knob.
To Set the Fence Angle
1. Slacken the star knob 11
2. Tilt the fence into the required angle.
3. Tighten the star knob.
The fine adjustment is used to eliminate possible tolerances in
the size of the biscuit slots.
Jointer Base Markings
When working without the fence, for example when making
T-joints, you can use the markings on the jointer base for proper
alignment of the tool.
1. Set the fence to the 0 ° position as described above.
2. For workpieces with a thickness of 19 mm, use the edge of
the base as a reference for centring.
3. For other workpieces, use the red centreline markings to
align the tool.
4. Two of the markings indicate the length of the cut. In order
to prevent breaking through the workpiece, make sure that
the workpiece extends beyond these markings.
Plunge Depth Adjustment (Fig. D)
The plunge depth must be set to match the biscuit size. The
numbers 0, 10 and 20 on the depth adjusting knob correspond
with the biscuit size. The M represents the maximum cutting
depth of approx. 20 mm.
• Turn the depth adjusting knob
aligning the appropriate number with the red marking on
the tool.
Plunge Depth Fine Adjustment (Fig. E)
The fine adjustment is used to eliminate possible tolerances in
the size of the biscuit slots.
1. Raise the fence 6 to its upper position as described above.
2. Insert the hex screwdriver as shown and adjust the plunge
depth as required by turning the screw (turn clockwise to
decrease the plunge depth).
3. Check the setting by making a trial cut in a piece of
scrap wood.
nOtE: The maximum cutting depth of 20mm is obtainable only
with a new blade and by backing out the fine adjustment screw
(see next section).
Anti-Slipping Pins (Fig. F)
The anti-slipping pins 7 help to reduce the tendency of the
biscuit jointer to slide to the right when cutting. When working
on visible parts of the workpiece, you may want to retract them
in order to avoid scratching.
1. To retract the pins, rotate them slightly clockwise using a
flat screwdriver.
2. To use the pins again, rotate them slightly counterclockwise.
26
4 as required. With the fence set to
.
8 into the required position,
Replacing the Blade (Fig. G, H, I)

WARNING:
• Make sure that the teeth of the cutter point in
counterclockwise direction as shown (Fig. H).
• After replacing the blade, always check the cutting
depth and adjust if necessary.
• Do not use blades or larger or smaller diameter than
recommended. For the proper blade rating refer to the
technical data.
• Use only blades specified in this manual complying
with EN847-1.
1. Remove the four hex screws
take off the cover.
2. Depress the spindle lock
turning it counterclockwise.
3. Change the blade.
4. Tighten the flange securely by turning it clockwise while
keeping the spindle lock depressed.
5. Mount the cover plate and tighten the hex screws.
Dust Extraction (Fig. J1, J2)
Using the appropriate adapter, you can connect either a dustbag
or a dust extractor.
Dust Extractor
1. Insert the appropriate adapter
extraction outlet 5 .
2. Connect the dust extractor hose to the adapter.
Dustbag
1. Insert the straight adapter
outlet 5 .
2. Attach the dustbag 15
3. Whenever possible, connect a dust extraction device
designed in accordance with the relevant regulations
regarding dust emission.

OPERATION

Instructions for Use

WARNING: Always observe the safety instructions and
applicable regulations.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
Proper Hand Position (Fig. U)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
12 from the base plate and
10 and remove the flange by
13 or 14 into the dust
13 into the dust extraction
to the adapter.