Sealey cp12035v.v2 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard this product
will, if used according to these instructions and properly maintained, give you years of
trouble free performance.
IMPORTANT: PLEASE READ ThESE iNSTRucTioNS cAREFuLLY. NoTE ThE SAFE oPERATioNAL REQuiREMENTS, WARNiNGS, AND
cAuTioNS. uSE ThiS PRoDucT coRREcTLY, AND WiTh cARE FoR ThE PuRPoSE FoR Which iT iS iNTENDED. FAiLuRE To Do So
MAY cAuSE DAMAGE AND/oR PERSoNAL iNJuRY AND WiLL iNvALiDATE ThE WARRANTY.
1. SAFETY iNSTRucTioNS
1.1 GENERAL SAFETY.
Disconnect the battery from the drill unit before changing

accessories, servicing or performing any maintenance.
Maintain the drill and battery in good condition. Check moving

parts alignment on a regular basis.
Replace or repair damaged parts. Use an authorised service

agent and recommended parts only. Unauthorised parts may
be dangerous and will invalidate the warranty.
Ensure the drill is switched off before installing the battery pack.

Keep the drill and charger clean for best and safest performance.

Remove ill fitting clothing. Remove ties, watches, rings and

other loose jewellery and contain long hair.
Evaluate your working area before using the drill e.g. ceiling,

floors and enclosures may contain electrical items or water piping.
Ensure battery pack is correctly inserted into the drill handle

and latched in place before attempting to switch on drill.
Secure loose workpieces with a clamp, vice or other adequate

holding device.
Avoid unintentional starting.

Wear approved safety eye protection (standard spectacles are

not adequate).
Maintain correct balance and footing. Ensure the floor is not

slippery and wear non-skid shoes.
Be aware that this drill does not need to be plugged into the

mains power.
Keep chuck direction switch in the locked position until the drill

is required for use.
Keep children and unauthorised persons away from the

working area.
DO NOT use the drill where there are flammable liquids, solids

or gases, such as paint solvents, etc.
DO NOT allow children to operate the drill.

DO NOT operate the drill if any parts are missing as this may

cause failure or possible personal injury.
DO NOT hold unsecured workpiece in your hand.

DO NOT leave the drill operating whilst unattended.

DO NOT carry the drill with your finger on the power switch.

Keep chuck direction switch in the locked position.
DO NOT use the drill for a task it is not designed to perform.

DO NOT operate the drill when you are tired or under the

influence of alcohol, drugs or intoxicating medication.
DO NOT get the drill or battery charger wet or use in damp or

wet locations.
Keep drill and charger in the case and store in a safe, dry,

childproof area where the temperature will not exceed 104°F
(40°C).
1.2 BATTERY SAFETY iNSTRucTioNS.
WARNING! Battery contains nickel-cadmium which is dangerous.

Handle with care to avoid damage, fire, corrosion or personal
injury.
Charge battery prior to its first use. The battery pack will have

been shipped in a low charge state.
Use only the charging base provided to charge the drill battery.

DO NOT charge battery when room temperature is below 50°F

(10°C) or above 104°F (40°C).
DO NOT attempt recharging the battery by means of an engine

generator or a DC power source.
DO NOT short-circuit the battery by linking both terminals with

a metal object, or your fingers etc.
DO NOT store the battery (or drill) in locations where the

temperature may exceed 104°F (40°C) such as outside sheds,
above heaters, or metal buildings in summer.
cordless drill/drivers
INSTRUCTIONS FOR MODEl NOS:
cP12035v.v2 (12v)
cP18035v.v2 (18v)
WARNING! Dispose of spent batteries correctly as they

contain nickel-cadmium. DANGER! DO NOT attempt to
disassemble the battery pack. For safety and environmental
reasons DO NOT discard in domestic waste or by burning.
ONLY discard or recycle according to local authority regulations.
WARNING! DO NOT allow a leaking battery to contact your

person. If you come into contact with battery liquid take the
following immediate action:
 a) Skin contact: Wash immediately with soap and water,
then wash flesh in either lemon juice or vinegar.
 b) Eye contact: Wash with a strong solution of boric acid,
and seek immediate medical attention.
1.3 ELEcTRicAL SAFETY.
REGARDING DIRECT MAINS POWER USE WITH THE
CHARGING BASE AND TRANSFORMER PLUG ONLY.
WARNiNG! It is the owner's responsibility to read, understand

and comply with the following electrical instructions:
You must ensure the risk of electric shock is minimised by the
installation of appropriate safety devices. An RCCB (Residual
Current Circuit Breaker) should be incorporated in the main
distribution board. We also recommend that an RCD (Residual
Current Device) is used with all electrical products, particularly
portable equipment which is plugged into an electrical supply
not protected by an RCCB.You must also read and understand
the following instructions concerning electrical safety.
1.3.1 The Electricity At Work Act 1989 requires all portable
electrical appliances, if used on business premises, to be
tested by a qualified electrician, using a Portable
Appliance Tester (PAT), at least once a year.
1.3.2 The Health & Safety at Work Act 1974 makes owners of
electrical appliances responsible for the safe condition of the
appliance, and the safety of the appliance operator. If in any
doubt about electrical safety, contact a qualified electrician.
1.3.3 You must ensure that you:
Inspect the transformer plug, cable, adaptor and the charging

base for wear and damage to ensure items are safe before
connecting to the mains power supply. If worn or damaged DO
NOT use. Immediately replace or contact a qualified electrician.
Check cables are always protected against short circuit and

overload.
Important: Check that the voltage marked on the transformer

plug is the same as the power supply to be used.
Uncoil the power cable between the transformer and the

charging base before use.
DO NOT pull or carry the charging base by the transformer power

lead, or pull the transformer plug from the mains socket by the
power lead.
DO NOT use any other type of transformer with the charging base.

DO NOT place the power connector into any area of charging

base except the correct socket (beneath the green power light
bulb).
DO NOT try to open or dis-assemble the transformer plug or

charging base.
DO NOT use the transformer plug to power any other electrical

item.
DO NOT get the transformer wet, or use in wet, damp

conditions (for indoor use only).
WARNiNG! NEVER substitute a standard 13Amp 3 pin plug, or

any other type of plug, for the transformer plug.
1.4 BATTERY chARGiNG BASE SAFETY iNSTRucTioNS.
WARNING! DO NOT use the charging base to charge any

battery other than that supplied for the drill. Other types of
batteries may explode!
Original Language Version
CP12035V.V2 & CP18035V.V2 Issue No.2 - 17/08/10