DeWalt DCCS623 Instruction Manual page 9

13 . Use extreme caution when re‑entering a previous cut.
Engage the ribbed bumpers
the chain to reach full speed before proceeding with a cut.
14 . Do not attempt plunge cuts or bore cuts.
15 . Watch for shifting logs or other forces that could
close a cut and pinch or fall into chain.
Kickback Safety Features

WARNING: The following features are included
on your saw to help reduce the hazard of kickback;
however such features will not totally eliminate this
dangerous reaction. As a pruner user do not rely
only on safety devices. You must follow all safety
precautions, instructions, and maintenance in this
manual to help avoid kickback and other forces which
can result in serious injury.
• Reduced‑Kickback Guide Bar, designed with a small radius
tip which reduces the size of the kickback danger zone on
bar tip. A reduced ‑ kickback guide bar is one which has
been demonstrated to significantly reduce the number and
seriousness of kickbacks when tested in accordance with
safety requirements for electric pruners.
• Low‑Kickback Chain, designed with a contoured depth
gauge and guard link which deflect kickback force and
allow wood to gradually ride into the cutter. A low‑kickback
chain is a chain which has met kickback performance
requirements of ANSI B175.1–2012.
• Do not operate pruner while in a tree, on a ladder, on a
scaffold, or from any unstable surface.
• Hold tool by insulated gripping surfaces when performing
an operation where the cutting tool may contact hidden
wiring. Contact with a "live" wire will make exposed metal
parts of the tool "live" and shock the operator.
• Do not attempt operations beyond your capacity or
experience. Read thoroughly and understand completely all
instructions in this manual.
• Before you start pruner, make sure saw chain is not
contacting any object.
• Do not operate a pruner with one hand! Serious injury to the
operator, helpers, or bystanders may result from one handed
operation. A pruner is intended for two‑handed use only.
• Keep the handles dry, clean, and free of oil or grease.
• Do not allow dirt, debris, or sawdust to build up on the
motor or outside air vents.
• Stop the pruner before setting it down.
• Do not cut vines and/or small under brush.
• Use extreme caution when cutting small size brush and
saplings because slender material may catch the saw chain
and be whipped toward you or pull you off balance.
Pruner Names and Terms
Bucking ‑ The process of cross cutting a felled tree or log
•
into lengths.
Motor Brake (if equipped) ‑ A device used to stop the saw
•
chain when the trigger is released.
Pruner Powerhead ‑ A pruner without the saw chain and
•
guide bar.
21 onto the wood and allow
Drive Sprocket or Sprocket ‑ The toothed part that drives
•
the saw chain.
Felling ‑ The process of cutting down a tree.
•
Felling Back Cut ‑ The final cut in a tree felling operation
•
made on the opposite side of the tree from the notching cut.
Front Handle ‑ The support handle located at or toward
•
the front of the pruner.
Front Hand Guard ‑ A structural barrier between the front
•
handle of a pruner and the guide bar, typically located
close to the hand position on the front handle.
• Guide Bar ‑ A solid railed structure that supports and
guides the saw chain.
Scabbard/Guide Bar Cover ‑ Enclosure fitted over guide
•
bar to help prevent tooth contact when saw is not in use.
• Kickback ‑ The backward or upward motion, or both of the
guide bar occurring when the saw chain near the nose of
the top area of the guide bar contacts any object such as a
log or branch, or when the wood closes in and pinches the
saw chain in the cut.
Kickback, Pinch ‑ The rapid pushback of the saw which
•
can occur when the wood closes in and pinches the moving
saw chain in the cut along the top of the guide bar.
• Kickback, Rotational ‑ The rapid upward and backward
motion of the saw which can occur when the moving saw
chain near the upper portion of the tip of the guide bar
contacts an object, such as a log or branch.
Limbing ‑ Removing the branches from a fallen tree.
•
• Low‑Kickback Chain ‑ A chain that complies with the
kickback performance requirements of ANSI B175.1–2012
(when tested on a representative sample of pruners.)
Normal Cutting Position ‑ Those positions assumed in
•
performing the bucking and felling cuts.
• Notching Undercut ‑ A notch cut in a tree that directs the
tree's fall.
Rear Handle ‑ The support handle located at or toward
•
the rear of the saw.
• Reduced Kickback Guide Bar ‑ A guide bar which has
been demonstrated to reduce kickback significantly.
Replacement Saw Chain ‑ A chain that complies with
•
kickback performance requirements of ANSI B175.1–2012
when tested with specific pruners. It may not meet the ANSI
performance requirements when used with other saws.
• Saw Chain ‑ A loop of chain having cutting teeth, that cut
the wood,and that is driven by the motor and is supported
by the guide bar.
Ribbed Bumper ‑ The ribs used when felling or bucking to
•
pivot the saw and maintain position while sawing.
• Switch ‑ A device that when operated will complete
or interrupt an electrical power circuit to the motor of
the pruner.
Switch Linkage ‑ The mechanism that transmits motion
•
from a trigger to the switch.
Switch Lockout ‑ A movable stop that prevents
•
the unintentional operation of the switch until
manually actuated.
English
7