Adjustment - Kenwood CS-6040 Instruction Manual

HOW TO CHANGE SETTING OF READOUT
CALENDAR AND CLOCK
To turn on and off the calendar and clock display or change
their setting, follow the procedures below.
(1) Press A and X - Y of the HORIZONTAL MODE s w i t c h e s
(shaded s w i t c h e s in the figure) simultaneously. (For
functions of the H O R I Z O N T A L MODE s w i t c h e s , refer
to section 0 0 . ) LEDs in the A and X - Y switches light up.
If this condition is left without executing any of opera-
tions ( 2 ) , ( 3 ) , and (5) below, the previous state is re-
stored after approx. 5 seconds automatically.
H O R I Z O N T A L M O D E S w i t c h O p e r a t i o n (
Fig. 6 5
(2) To turn off the calendar and clock display, press B of
the H O R I Z O N T A L MODE s w i t c h e s (shaded s w i t c h in
the figure) after operation (1).
T u r n i n g O N / O F F C a l e n d a r a n d C l o c k D i s p l a y
(3) T o turn on the calendar and clock display again, press
B of the HORIZONTAL MODE s w i t c h e s (shaded s w i t c h
in the figure) after operation (1).
(4) To correct the calendar and clock setting, follow the
steps below. T h e calendar and clock display must be
turned on for this correction.
© Press A INT B s w i t c h (shaded s w i t c h in the figure)
after operation (1).
" M o n t h " of the calendar and clock display flashes.
C o r r e c t i o n o f C a l e n d a r a n d C l o c k D i s p l a y
( 2 ) Rotate the S W E E P T I M E / D I V control to set a proper
month.
@ Pressing the X - Y s w i t c h shifts the flashing position
to the right. T h e second digit of the " D a y " of the
display now flashes.
® Set the second digit of the " D a y " by rotating the
S W E E P T I M E / D I V control.
© Repeat operations ® and © to set proper values to
the first digit of the " M i n u t e " .
© On completion of setting up to the first digit of the
" M i n u t e " , press the X - Y s w i t c h again. Correction
of the calendar and clock display is completed, and
the previous state is restored. " M i n u t e " is counted
from 0 second at this time.
48

ADJUSTMENT

Fig. 66
Fig. 67
Example: Correction of Calendar and Clock Display.
© Make " M o n t h " display f l a s h .
" J A N " - 2 2 - 7 8 15 : 3 8
T
Flashing
@ Set " M o n t h " .
" N O V " - 2 2 - 7 8
t
Flashing
© Shift flashing position to the right.
NOV - - 7 8 15 : 3 8
'JT2
Flashing
© Set second digit of " D a y " .
NOV - _U_'2 - 7 8 15 : 3 8
Flashing
© Shift flashing position to the right.
© Set second digit of " Y e a r " .
NOV - 1 5 - 15 : 3 8
'J£8
Flashing
© Shift flashing position to the right.
® Repeat setting up to first digit of " M i n u t e " .
NOV - 1 5 - 8 8 15 : 3 " 5 "
© Correction of calendar and clock is completed.
15 : 3 8
Flashing