Sealey SA203 Instructions

Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH
IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE
THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
 Follow all workshop safety rules, regulations, and conditions when using wrench.
 WARNING! Disconnect from the air supply before changing accessories or servicing.
 Maintain the wrench in good condition and replace any damaged or worn parts. Use
genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
 WARNING! Check correct air pressure is maintained and not exceeded. We recommend 90psi.
 Keep the air hose away from heat, oil and sharp edges. Check the air hose for wear before
each use and ensure that all connections are secure.
 Only use impact sockets which are specifically designed for use with an impact wrench.
 Wear approved safety eye/face shield, ear defenders and hand protection.
 WARNING! Due to the possible presence of asbestos dust from brake linings, when working
around vehicle brake systems it is recommended that suitable respiratory protection is worn.
 Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
 Keep children and non essential persons away from the working area.
 DO NOT use worn, or damaged sockets.
 DO NOT use the wrench for a task that it is not designed to perform.
 WARNING! DO NOT use wrench if damaged or thought to be faulty. Contact a Service Agent.
 DO NOT use wrench unless you have been instructed in its use by a qualified person.
 DO NOT carry the wrench by the air hose, or yank the hose from the air supply.
 DO NOT operate wrench if you are tired or under the influence of alcohol, drugs or intoxicating
medication.
 DO NOT carry the wrench with your hand on the power trigger, in order to avoid unintentional
starting.
 DO NOT direct air from the air hose at yourself or others.
 When not in use, disconnect from air supply and store in a safe, dry, childproof location.
NOTE: Use a Calibrated Torque Wrench for Final Tightening
2. INTRODUCTION & SPECIFICATION
Fitted with powerful twin hammer mechanism all housed in a compact design. Handle exhaust
reduces noise output and limits the circulation of brake dust on wheel applications. Features three
position torque/air control in forward and reverse. Mini size allows use in confined engine bay
areas. Suitable for garage, tyre shop and workshop applications.
Working/Maximum Torque:. . . . . . . 375/400lb.ft
Ultimate Torque: . . . . . . . . . . . . . . . . . . .450lb.ft
Air Consumption: . . . . . . . . . . . . . . . . . . 5.8cfm
Noise Power: . . . . . . . . . . . . . . . . .104.45dB(A)
Noise Pressure: . . . . . . . . . . . . . . . .93.45dB(A)
© Jack Sealey Limited
Speed: . . . . . . . . . . . . . . . . . . . . . . . . 11000rpm
Operating Pressure: . . . . . . . . . . . . . . . . . 90psi
Air Inlet Size: . . . . . . . . . . . . . . . . . . . . 1/4"BSP
Weight: . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.6kg
Drive: . . . . . . . . . . . . . . . . . . . . . . . . . . . . ½"Sq
Original Language Version
INSTRUCTIONS FOR:
AIR IMPACT WRENCH ½"SQ
DRIVE MINI TWIN HAMMER
SA203
MODEL No:
SA203 Issue:3(SP) - 18/06/13