Related Manuals for Canon Multi Function Professional Puncher-A1
Summary of Contents for Canon Multi Function Professional Puncher-A1
- Page 1 Multi Function Professional Puncher-A1 Installation Procedure PRINTED IN USA XXXXXXXXXX PUB No. FT2-0208-030 © CANON INC. 2016 閲 FT2-0208-030_20160510.pdf 2016/05/10 14:39:51...
-
Page 2: Table Of Contents
1. Installation Installation How to Check this Installation Procedure........3 Pre-checks................4 Unpacking................. 5 Installation Procedure..............7 Connection Check..............17 閲 FT2-0208-030_20160510.pdf 2016/05/10 14:39:51... -
Page 3: How To Check This Installation Procedure
1. Installation How to Check this Installation Procedure Symbols in the Illustration The frequently-performed operations are described with symbols in this procedure. Screw Tighten Loosen Packaged Item Unused Parts Remove Install Harness (Common for Guides Connector Power Cord and Clamps) Connect Disconnect Connect... -
Page 4: Pre-Checks
1. Installation Pre-checks Checking the Contents NOTE: Name of This Product • [4] ：Not used when connecting a LAN communication model. (the installation procedure is Safety regulations require the product's name to be described in the Installation Procedure for the registered. -
Page 5: Unpacking
1. Installation Unpacking 5. Make this equipment stand on its bottom, and remove the plastic bag. CAUTION: CAUTION: When installing this equipment, note the following points. Do not lift this equipment too high. The weight of this equipment is approx. 103 kg. It is recommended to lift it with 4 or more people. - Page 6 1. Installation 7. Open the Front Cover and remove the tapes and packaging materials. CAUTION: • When delivering the pre-installed machine to the user site by a truck or other means, do not remove the tape shown below in order to keep the handle of the waste box unscratched.
-
Page 7: Installation Procedure
1. Installation Installation Procedure 2. Install the 2 Latch Plates of the host machine or Buffer Pass Unit. Check Items When Turning • 4 Screws (Binding; M4x10) OFF the Main Power Check that the main power of the host machine is OFF. 1. - Page 8 1. Installation ■ In the Case of Document Insertion Unit 1. Open the Front Cover of this equipment. 1. Install the 2 Latch Plates to the Document Insertion Unit. • 4 Screws (Binding; M4 x10) 2. Loosen the screw, and turn the connection lever to raise the hook.
- Page 9 1. Installation Adjusting the Height 3. Fit the positioning pin hole of this equipment onto the Positioning Pin of the host machine. ■ Checking the Height with Respect to the Host Machine 1. Adjusting the Height Check that the height difference between the top of this equipment and the left side top of the host machine is within +/-2.0 mm.
- Page 10 1. Installation ● Adjusting the Front Casters 2. If the difference in height is within +/-2.0 mm, fully tighten the screw of the Connection Lever, and then close the Front Cover. 3. If the height difference is more than +/-2.0 mm, adjust the height as described in "Adjusting the Casters".
- Page 11 1. Installation ● Adjusting the Rear Casters 6. Return, the Cover Plates (Left and Right) to the original positions. 1. When making adjustments, disengage from upper • 2 Screws each stream devices. 2. Remove the 2 Cover Plates (Left and Right). •...
- Page 12 1. Installation Connecting the Cables ■ Connecting the Shunt Cable ● Connection with the Host Machine or Buffer Pass Unit 1. Connect the Shunt Cable. < imagePRESS C10000VP/8000VP Series > • Remove the screws from the host machine, and connect the Shunt Cable. 4.
- Page 13 1. Installation < iR-ADV 8505/8595/8585 Series > < iR-ADV C7580/7570/7565 Series_imagePRESS • Remove the screws from the host machine and this C850/750/650 Series > equipment, and connect the Shunt Cable. • Remove the screws from the Buffer Pass Unit and the host machine, and connect the Shunt Cable.
- Page 14 1. Installation ● Connection with the Document Insertion Unit 1. Remove the Face Cover on the rear side of this equipment. (the removed Face Cover and screw willnot be used.) • 1 Screw 1. Remove the screw from the Document Insertion Unit and the equipment, and connect the Shunt Cable.
- Page 15 1. Installation <Case of imagePRESS C850/750/650 Series > 3. Insert the LAN Cable to the host machine and this equipment (the port for connection with the upstream equipment), and install the 2 Wire Saddles. < Case of imagePRESS C10000VP/8000VP series> <...
- Page 16 1. Installation Connection of the Interface Cable 1. Connect the Interface Cable to the Finisher to connect to this equipment. CAUTION: Perform the following work only for iR-ADV C7580/7570/7565 series. For the procedure for connecting the Interface Cable, refer to the Finisher's manual.
-
Page 17: Connection Check
1. Installation Connection Check 4. Turn ON the main power switch of the host machine ( Excludes imagePRESS C10000VP/C8000VP series). If a message prompting the user to update the version 1. Connect the Power Cord to the plug of this appears, press [Update] to automatically update the equipment. - Page 18 閲 FT2-0208-030_20160510.pdf 2016/05/10 14:39:52...
- Page 19 閲 FT2-0208-030_20160510.pdf 2016/05/10 14:39:52...
- Page 20 閲 FT2-0208-030_20160510.pdf 2016/05/10 14:39:52...