Mitsubishi Electric GT10 General Description page 2

产品中有害物质的名称及含量
有害物质
部件名称
铅 汞 镉 六价铬 多溴联苯
(Pb) (Hg) (Cd) (Cr(VI)) (PBB)
显 示 器 外壳 ○ ○ ○ ○ ○
GOT
印刷基板 × ○ ○ ○ ○
1. Specifications
1.1 General Specifications
Item
Display section 0 to 50C
Operating ambient
temperature
Other than display section 0 to 55C *4
(When mounted horizontally), 0 to 50C (When mounted vertically)
Storage ambient temperature -20 to 60C
Operating/Storage ambient humidity 10 to 90% RH, non-condensing (The wet bulb temperature is 39C or less.)
Conforms to JIS
Vibration resistance B3502 and
IEC61131-2
Shock resistance Conforms to JIS B3502, IEC 61131-2 (147m/s
Must be free of lamp black, corrosive gas, flammable gas, or excessive amount of electro conductive dust particles and
Operating atmosphere
must be no direct sunlight. (Same as for saving)
*1 2000 m (6562 ft) max.
Operating altitude
Installation location Inside control panel
Overvoltage category *2 II or less
Pollution degree *3 2 or less
Cooling method Self-cooling
*1 Do not use or store the GOT under pressure higher than the atmospheric pressure of altitude 0m (0ft.). Failure to observe this instruction may cause a malfunction.
When the air inside the control panel is purged by pressurization, the surface sheet may be lifted by high pressure. As a result, the touch panel may be difficult to press,
and the sheet may be peeled off.
*2 This indicates the section of the power supply to which the equipment is assumed to be connected between the public electrical power distribution network and the
machinery within the premises. Category II applies to equipment for which electrical power is supplied from fixed facilities.
The surge voltage withstand level for up to the raged voltage of 300 V is 2500 V.
*3 This index indicates the degree to which conductive material is generated in the environment where the equipment is used.
In pollution degree 2, only non-conductive pollution occurs but temporary conductivity may be produced due to condensation.
*4 When a protective cover for oil is mounted on the GOT, the maximum operating ambient temperature must be 5°C lower than the one described above.
1.2 Performance Specifications
Item
GT1055-QSBD
Type STN color liquid crystal
Screen size 5.7"
Resolution 320  240 dots (Horizontal format)
W115(4.53)  H86(3.39) [mm](inch) (Horizontal format)
Display size
Display
16-dot standard font: 40 characters  15 lines, 12-dot standard font: 53 characters  20 lines (Horizontal format)
Display character
section *1
Display color 256 colors
Contrast adjustment 16-level adjustment
Intensity of LCD only 2
380 [cd/m ]
Life Approx. 50,000h. (Time for display intensity to become 1/5 at operating ambient temperature of 25C)
Cold cathode fluorescent tube (irreplaceable by a user) backlight shutoff detection function is included.
Backlight
Backlight off/screen saving time can be set.
Approx. 75,000h or longer (Time for display intensity reaches
*2
Life
50% at the operating ambient temperature of 25C)
Green light : Power is supplied
Orange light : Screen saving
LED (POWER LED)
Green / Orange flashing : Blown backlight bulb
POWER LED is not lit : Power is not supplied
Number of touch keys Maximum 50 keys/screen (Matrix resistive film touch panel)
Key size Minimum 16  16 dots (per key)
Touch
Simultaneous pressing of two
panel
(or more) areas Enable
(2-point press)
Life 1 million times or more (operating force 0.98N max.)
*3 Flash memory ROM (Internal), for storing project data (3M bytes or less) and OS
C drive
Memory
Life (Number of write times) 100,000 times
D drive SRAM (Internal), for storing alarm history, recipe data and time action setting value
本表格依据SJ/T 11364的规定编制。
○:表示该有害物质在该部件所有均质材料中的含量均在GB/T 26572
多溴
规定的限量要求以下。
二苯醚
×:表示该有害物质至少在该部件的某一均质材料中的含量超出GB/T
(PBDE)
26572规定的限量要求。
○
○
Specifications
GT1055-QSBD/GT1050-QBBD
Frequency Acceleration Half-amplitude
5 to 9Hz -- 3.5mm
Under intermittent
vibration
2
9 to 150Hz 9.8m/s
5 to 9Hz -- 1.75mm
Under continuous
vibration
9 to 150Hz 4.9m/s 2
2 , 11 ms, Sine half-wave pulse, 3 times each in the X, Y, and Z directions.)
Specifications
GT1050-QBBD
STN monochrome (white/blue) liquid crystal
Monochrome (white/blue), 16 scales
2
260 [cd/m ]
Approx. 54,000h or longer (Time for display intensity reaches
50% at the operating ambient temperature of 25C)
Item
Battery
Type
Backup target
Life
Buzzer output (a buzzer that sounds
when touch keys are pressed)
Environmental protective structure
External dimensions
RS-422/485
Built-in
RS-232
interface
Sweep Count
--
10 times each in X,
USB
Y and Z directions
GT10-50FMB
--
Panel cutting dimensions
Weight
Compatible software package
*1 • Bright dots (always lit) and dark dots (unlit) may appear on a liquid crystal display panel. It is impossible to completely avoid this symptom, as the liquid crystal display
comprises of a great number of display elements. Flickers may be observed depending on the display color.
Please note that these dots appear due to its characteristic and are not caused by product defect.
• Flickers and partial discoloration may be generated on the liquid crystal display panel due to the display contents or the contrast adjustment.
However, please note that these phenomena appear due to its characteristic and are not caused by product defect.
• There is a difference in the display brightness and the color tones between liquid crystal display panels.
When using multiple liquid crystal display panels, please note that there is an individual difference between them.
• A crosstalk (shadow as an extension of the display) may appear on the liquid crystal display panel. Please note that it appears due to its characteristic.
• When the display section is seen from the outside of the display angle, the display color seems like it has changed. Please note that it is due to its characteristic.
Please note that the response time, brightness and color of the liquid crystal display panel may vary depending on the usage environmental temperature.
Especially in the low temperature environment, the display response becomes slow due to the characteristics of the STN liquid crystal.
Please check the display response in advance for using this product.
• When the same screen is displayed for a long time, an incidental color or partial discoloration is generated on the screen due to heat damage, and it may not
disappear. To prevent heat damage, the screen saver function is effective. For details on the screen saver function, refer to the following.
 GT10 User's Manual
*2 Using the GOT Backlight OFF function can prolong the life of the backlight. For details on the Backlight OFF function, refer to the following.
 GT10 User's Manual
*3 ROM in which new data can be written without deleting the written data.
*4 Note that this does not guarantee all users' operation environment.
In addition, the product may not be used in environments under exposition of oil or chemicals for a long period of time, or in environments filled with oil-mist.
*5 Set the terminating resistor selector switch of the GOT in accordance with the connection type when adopting GOT multidrop connection.
For details of GOT multidrop connection, refer to the following.
 GOT1000 Series Connection Manual
1.3 Power Supply Specifications
(For details on power supply wiring, such as the allowable cable size and tightening
torque, refer to the additional manual, "GT10 User's Manual".)
Item
Input power supply voltage 24VDC (+10% -15%)
Fuse (built-in, not
1.0A
exchangeable)
9.84W (410mA/24VDC)
Power consumption, or less,
(At backlight off) (4.32W (180mA/24VDC)
or less)
Inrush current 15A or less (26.4VDC) 2ms
Permissible instantaneous
Within 5ms
power failure time *1
Noise voltage: 1000Vp-p, Noise width: 1s (by noise
Noise immunity
simulator of 30 to 100Hz noise frequency)
Dielectric withstand 500VAC for 1 minute (across power supply terminals
voltage and earth)
10M or larger by insulation resistance tester
Insulation resistance
(across power supply terminals and earth)
Grounding with a ground resistance of 100 Ω or less
by using a ground cable that has a diameter of 1.6
Grounding
mm or more. If impossible, connect the ground cable
to the control panel.
*1 The GOT continues to operate even upon 5ms or shorter instantaneous
power failure.
The GOT stops operating if there is extended power failure or voltage drop,
while it automatically resumes operation as soon as the power is restored.
Specifications
GT1055-QSBD
GT11-50BAT lithium battery
Magnesium maganese dioxide lithium primary battery
Clock data, alarm history and recipe data
Approx. 5 years (Operating ambient temperature of 25)
Single tone (LONG/ SHORT/ OFF adjustable)
*4 Equivalent to IP67 (JEM1030) (front section)
W164(6.46)  H135(5.32)  D56(2.21)[mm](inch) (Excluding mounting fixtures) (Horizontal format)
Conforming to serial RS-422/485 standard, 1ch
Transmission speed: 115,200/57,600/38,400/19,200/9,600/4,800bps
Connector shape : D-sub 9-pin (Female)
Application : PLC communication
*5
Terminating resistor : Open/110/330(Switched by terminating resistor selector switch) (At factory shipment: 330)
Conforming to serial RS-232 standard, 1ch
Transmission speed : 115,200/57,600/38,400/19,200/9,600/4,800bps
Connector shape : D-sub 9-pin (Male)
Application : PLC communication, bar code reader connection, PC communication
(Project data upload/download, OS installation, transparent function)
Conforming to serial USB (Full Speed 12Mbps), device, 1ch
Connector shape: Mini-B
Application : PC communication (Project data upload/download, OS installation, transparent function)
For connecting GT10-50FMB memory board
W153 (6.03)  H121(4.77) [mm] (inch) (Horizontal format)
0.7kg (Excluding mounting fixtures)
GT Designer2 Version 2.90U or later/GT Designer3 Version 1.01B or later
This manual confers no industrial property rights or any rights of any other
kind, nor does it confer any patent licenses. Mitsubishi Electric Corporation
cannot be held responsible for any problems involving industrial property rights
Specifications
which may occur as a result of using the contents noted in this manual.
GT1055-QSBD GT1050-QBBD
Warranty
Exclusion of loss in opportunity and secondary loss from warranty liability
Regardless of the gratis warranty term, Mitsubishi shall not be liable for
compensation to:
(1) Damages caused by any cause found not to be the responsibility of
Mitsubishi.
9.36W (390mA/24VDC)
(2) Loss in opportunity, lost profits incurred to the user by Failures of Mitsubishi
or less,
products.
(4.32W (180mA/24VDC)
(3) Special damages and secondary damages whether foreseeable or not,
or less)
compensation for accidents, and compensation for damages to products
other than Mitsubishi products.
(4) Replacement by the user, maintenance of on-site equipment, start-up test run
and other tasks.
•
This product has been manufactured as a general-purpose part for general
industries, and has not been designed or manufactured to be incorporated in
a device or system used in purposes related to human life.
•
Before using the product for special purposes such as nuclear power, electric
power, aerospace, medicine or passenger movement vehicles, consult with
Mitsubishi Electric.
•
This product has been manufactured under strict quality control. However
when installing the product where major accidents or losses could occur if the
product fails, install appropriate backup or failsafe functions in the system.
HEAD OFFICE : TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN
GT1050-QBBD
For safe use