Table of Contents
Advertisement
Quick Links
Covered Boom Kit
Multi Pro
Model No. 41602-Serial No. 316000001 and Up
Loose Parts
Use the chart below to verify that all parts have been shipped.
1
2
3
4
5
6
7
8
Important: Use air-induction, flat-fan nozzles with the covered boom kit to avoid chemical buildup on the covers
during application. Refer to the Toro nozzle chart for details.
Note: Install the Spring Upgrade Kit (Part Number 120-8508) with the covered boom.
© 2016-The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
Turf Sprayer with Truss-Style Boom
Description
Pop rivet (3/16 x 1/2 inch)
Washer (3/16 inch)
Reinforcement plate
Wing-boom cover
Washer plate
Flange nut (5/16 inch)
Register at www.Toro.com.
Form No. 3406-554 Rev A
Installation Instructions
Qty.
-
Prepare the machine.
1
1
Prepare the center-boom cover (for an
1
11-nozzle assembly).
11
11
1
22
Attach an 11-nozzle boom cover to a
22
12-nozzle boom cover.
1
1
2
2
8
8
1
Install the center-boom brackets and
cover.
1
8
4
8
4
2
16
Install the wing-boom covers.
12
12
1
2
Install the drain-valve-mount bracket.
3
2
Move the drain valve.
2
Ensure that the boom covers have
-
proper clearance.
Original Instructions (EN)
All Rights Reserved *3406-554* A
Printed in the USA
Use
Advertisement
Table of Contents
Related Manuals for Toro 41602
Summary of Contents for Toro 41602
-
Page 1: Table Of Contents
Important: Use air-induction, flat-fan nozzles with the covered boom kit to avoid chemical buildup on the covers during application. Refer to the Toro nozzle chart for details. Note: Install the Spring Upgrade Kit (Part Number 120-8508) with the covered boom. -
Page 2: Procedure
Preparing the Machine Preparing the Center-Boom Cover (for an 11-Nozzle No Parts Required Assembly) Procedure Parts needed for this procedure: CAUTION 11-nozzle, center-boom cover Rubber cover If you leave the key in the ignition switch, someone could accidently start the engine and seriously Reinforcement plate injure you or other bystanders. -
Page 3: Reinforcement Plate
2. Align the holes on the reinforcement plate with the holes on the rubber cover (Figure Attaching an 11-Nozzle Boom Cover to a 12-Nozzle Boom Cover Parts needed for this procedure: 12-nozzle, center-boom cover Pop rivet (3/16 x 1/2 inch) Washer (3/16 inch) Figure 3 Rubber cover... -
Page 4: Center-Boom Bracket (2014 And Earlier Models)
2. Install 11 pop rivets (3/16 x 1/2 inch) and washers (3/16 inch) to the reinforcement plate, attaching 11-nozzle cover to the 12-nozzle cover (Figure Installing the Center-Boom Brackets and Cover Parts needed for this procedure: Center-boom bracket (2014 and earlier models) Boom-mount plate Figure 6 U-nut... -
Page 5: U-Nut
Installing the Drain-Valve-Mount Bracket Parts needed for this procedure: Drain-valve-mount bracket Carriage screw (5/16 x 1-1/4 inch) Flange nut (5/16 inch) g0302 99 Procedure Figure 8 2015 and later models 1. Remove the 2 carriage bolts (5/16 x 1 inch) and 2 flange locknuts (5/16 inch) that secure the fender and 1. -
Page 6: Flange Nut (5/16 Inch)
Moving the Drain Valve Parts needed for this procedure: Flange nut (5/16 inch) Flange-head bolts (5/16 x 1 inch) Procedure 1. Remove the lynch pin that secures the drain valve to the sprayer-pump bracket (Figure 11). Figure 10 1. Flange locknut (5/16 inch) 3. -
Page 7: Flange-Head Bolts (5/16 X 1 Inch)
3. Remove the 2 mounting pegs from the drain valve (A Figure 12). Figure 12 Figure 13 1. Mounting peg 3. Flange-head bolts (5/16 x 1 inch) 2. Drain valve 4. Flange locknuts (5/16 7. Move the drain valve outboard and down to secure the inch) valve to the bracket (B and C of Figure... - Page 8 Figure 14 2014 models and older 1. Washer plate (18) 6. Flange nut—3/8 inch (8) 11. Center-boom cover 2. Spray nozzle (properly oriented) 7. U-nut (16) 12. Wing-boom cover (2) 3. Truss frame (outer-boom section) 8. Center-boom bracket (4) 13. Hex-head bolt—5/16 x 1-1/4 inches (16) 4.
- Page 9 Notes:...
- Page 10 Notes:...
- Page 11 The Way Toro Uses Information Toro may use your personal information to process warranty claims, to contact you in the event of a product recall and for any other purpose which we tell you about. Toro may share your information with Toro's affiliates, dealers or other business partners in connection with any of these activities. We will not sell your personal information to any other company.
- Page 12 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact the Toro importer.