Sealey CP20VCL Quick Start Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMP P OR R TA TANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
TH H E P P RO O DUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PE E RS S ON N AL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Warning: Do not
instructions look directly into
the light
1. SAFETY
 Ensure the work light is switched off before installing the battery pack.
 Ensure the battery pack (sold separately) is correctly inserted into the work light and latched in place before attempting to switch
on.
 Maintain the work light in good condition.
 Replace or repair damaged parts. Use an authorised service agent and recommended parts only. Unauthorised parts may be
dangerous and will invalidate the warranty.
 DO NOT shine directly into your, another person's or animal's eyes.
 DO NOT allow children to use the lamp.
DO NOT cover or block the lens during use.

 DO NOT get the work light wet or use in damp or wet locations or in areas where there is condensation.
 Store the work light in the original box, in a safe, dry, childproof area.
2. INTRODUCTION
Cordless clip work light useful in any workspace. Robust design with integrated carry handle and 360° movement. SMD LED Technology
for ultra-bright illumination with 70 SMD LED lights producing 1800 lumens. Simple on/off switch with four levels of brightness. IP20 Rated.
Powered by 20V Lithium-ion battery (not included).
3. SPECIFICATION
Model No: .............................................................. CP20VCL
Battery: ......................... 20V 2Ah - Lithium-ion (not included)
Options: .................................................................................
2Ah: ..................................................................... CP20VBP2
4Ah: ..................................................................... CP20VBP4
6Ah: ..................................................................... CP20VBP6
IP Rating: ........................................................................IP20
IK Rating: ........................................................................IK07
LED Qty: ............................................................................ 70
LED type: .................................................... SMD LED 6500K
Lumen output: ........... 1800lm Max with 4 levels of brightness
.................................................. (25%, 50%, 75% and 100%)
Operating time: ......................................................................
2Ah CP20VBP2: ..................................................2hrs 30mins
4Ah CP20VBP4: .............................................................. 5hrs
6Ah CP20VBP6: ..................................................7hrs 30mins
Power: .............................................................................15W
4. OPERATION
Unpack the product and check contents. Should there be any damaged or missing parts contact your supplier immediately.
4.1. BATTERY INSTALLATION
4.1.1. To insert the battery align the tongues on the battery cartridge with the grooves on the rear of the work light, and slide into place.
Insert the battery all the way until it locks into place.
4.2. BATTERY REMOVAL
4.2.1. Hold the work light fi rmly and push the battery latch button, then slide and remove the battery.
4.3. TURNING THE WORK LIGHT ON AND OFF
4.3.1. The ON/OFF switch is located on the rear of the work light (fi g 1). Press once for 25% brightness, through to four times for 100%
brightness. Then press once to turn the work light off .
4.4. ROTATING THE WORK LIGHT
4.4.1. Firmly hold the base/handle and rotate the work light, through 360º, to the required angle (fi g 2).
© Jack Sealey Limited
20V CORDLESS SMD LED 1800LM WORK
LIGHT - BODY ONLY
CP20VCL
MODEL NO:
Original Language Version CP20VCL Issue 1 05/10/21