Panasonic LS-H A Series Instruction Manual

Laser Sensor Head
LS-H□-A
Thank you very much for purchasing Panasonic products.
Read this Instruction Man ual carefully and thoroughly for the correct and
optimum use of this product.
keep this manual in a convenient place for quick reference.
Kindly
Never use this product as a sensing device for personnel protection.
●
In case of using sensing devices for personnel protection, use
●
products which meet laws and standards, such as OSHA, ANSI or IEC
etc., for personnel protection applicable in each region or country.
Although this product corresponds to a Class 1 laser product, it is
●
dangerous to see the laser beam which has been passed through a
WARNING
viewing optical system such as a lens etc. Hence, please avoid this.
Use of control or adjustment or performance of procedures
●
other than those specified in this instruction manual may
result in hazardous radiation expose.
1
FOR SAFE USE OF A LASER PRODUCT
● In order to prevent the accident by laser product and protect the users,
JIS C 6802 "Safety of laser products" was established based on the
-2014
regulation of IEC (International electrotechnical Commission). This
regulation classifies laser products according to the level of hazard, and
provides the safety measures for respective classes.
This product are classified as "Class 1 laser products" according to
IEC 60825-1 (JIS C 6802
-2014
● Laser hazardous class
Classification according to IEC 60825-1
Class
Class 1 Safe under reasonably foreseeable conditions of operation
The following label is affixed on this product in accordance with the
●
Safety of laser product.
Warning label
・
In Japanese
(Based on JIS C 6802)
<Label position>
Direction of
laser emission
● When this product is used in China,
affix the Chinese warning label (acces-
sory) on the label in the product.
・ Laser emission indicator (green)
While laser is emitted, the laser emission indicator (green) of the sensor
head lights up.
This indicator is visible even when wearing laser protective glasses.
Direction of
laser emission
INSTRUCTION MANUAL
MJE-LSHA No.0075-18V
"Safety of laser products".
-2014)
(JIS C 6802
-2014 -2014
Description of hazardous evaluation
In English
(Based on IEC 60825-1)
Direction of
laser emission
In Chinese
(Based on GB 7247.1
Operation indicator (Orange)
Laser emission indicator (Green)
2 SPECIFICATIONS
Item Model No. (Note 1)
Applicable amplifier
H-SP mode
Sensing
FAST mode
range
STD mode
(Note 3)
U-LG mode
Operation indicator
Laser emission indicator
Ambient temperature
Ambient humidity
Emitting element
Material
Cable
Weight
Accessories
Notes: 1) The model No. with suffix '-C5' stands for the 5m cable length type.
(e.g.) LS-H91A-C5
2) The model No. of retroreflective type sensor with the suffix '-Y' is the sensor without the RF-330
reflector. Arrange the reflector separately.
(e.g.) LS-H91-A-Y
3) Configure the mode settings in the applicable amplifier LS-400 series.
3 CAUTIONS
This product has been designed to meet the specifications when it is used
along with the optional exclusive amplifier. If an amplifier other than the
exclusive amplifier is used, not only the specifications may not be met, but
it may also be a cause for malfunction or break down. Hence, please
ensure to use this product along with the optional exclusive amplifier.
This product has been developed / produced for industrial use only.
●
Always use the sensor with the connector to be joined to the amplifier.
●
Make sure that the power is off while wiring to the amplifier.
●
)
In case noise generating equipment (switching regulator, inverter motor
●
etc.) is used in the vicinity of this product, connect the frame ground
(F.G.) terminal of the equipment to an actual ground.
If power is supplied from a commercial switching regulator, ensure that
●
the frame ground (F.G.) terminal of the power supply is connected to an
actual ground.
Do not use the sensor during the initial transient time (0.5 sec.) just after
●
the power supply is switched on.
Do not run the wires together with high-voltage lines or power lines or put
●
them in the same raceway. This can cause malfunction due to induction.
Take care that the sensor head is not directly exposed to fluorescent
●
lamp from a rapid-starter lamp or a high frequency lighting device, as it
may affect the sensing performance.
The sensor head cable cannot be extended.
●
Make sure that stress is not applied directly to the sensor head cable
●
joint.
This sensor is suitable for indoor use only.
●
Do not allow any water, oil fingerprints, etc., which may refract light, or
●
dust, dirt, etc., which may block light, to stick to the emitting / receiving
surfaces of the sensor head. In case they are present, wipe them with a
clean, soft cloth or lens paper.
Do not use the sensor in vaporous, dusty or corrosive gas atmospheres.
●
Take care that the sensor does not come in contact with water, oil,
●
)
-2012
grease or organic solvents, such as, thinner, etc.
Make sure that the power is off while cleaning the emitting / receiving
●
windows of the sensor head.
Type Coaxial retroreflective type
LS-H91-A (Note 2)
LS-400 series
0.1 to 1m
0.1 to 1m
0.1 to 3m
0.1 to 5m
Orange LED (Lights up when amplifier output is ON)
Green LED (Lights up when laser is emitted)
-10 to +55℃ (No dew condensation or icing allowed), Storage: -20 to +70℃
35～85% RH, Storage: 35～85% RH
Red semiconductor laser Class 1 (IEC / JIS / GB standard)
(Max. output: 1mW or less, Peak emission wavelength: 655nm)
Enclosure: PBT (Attachment: PEI), Lens cover: Acrylic
0.1mm 2 shielded cable, 2m long
30g approx.
Connector for amplifier: 1 pc.
RF-330 (Reflector): 1 pc.
Warning label: 1 pc. (Chinese)
Diffuse reflective type
LS-H21-A
30 to 150mm
30 to 150mm
30 to 250mm
30 to 500mm
Connector for amplifier: 1 pc.
Warning label: 1 pc. (Chinese)