Table of Contents
Advertisement
Quick Links
Tri-Roller
Greensmaster
Model No. 04495—Serial No. 315000001 and Up
This product complies with all relevant European directives.
For details, please see the Declaration of Incorporation (DOI)
at the back of this publication.
WARNING
CALIFORNIA
Proposition 65 Warning
This product contains a chemical or chemicals
known to the State of California to cause cancer,
birth defects, or reproductive harm.
© 2015—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
3000 Series
Setup
Mounting the Pull Arm
Bumpers (Greensmaster 3050,
3100, 3150, and 3200)
Register at www.Toro.com.
1. Using the dimensions shown in
holes with a diameter of 5.6 mm (0.221 inch) on the
underside of each pull frame cross tube.
1
Figure 1
1. 49.3 cm (19.4 inches)
2. 9.0 cm (3.5 inches)
2. Mount the 2 recessed bumpers to the underside of each
pull frame cross tube with 2 washer-head self-tapping
screws
(Figure
2).
Original Instructions (EN)
All Rights Reserved *3390-887* B
Printed in the USA
Form No. 3390-887 Rev B
Operator's Manual
Figure
1, drill 2
3
2
G028061
3. 1.9 cm (3/4 inches)
4. Pull frame cross tube
4
Advertisement
Table of Contents
Related Manuals for Toro 04495
Summary of Contents for Toro 04495
- Page 1 Form No. 3390-887 Rev B Tri-Roller Greensmaster ® 3000 Series Model No. 04495—Serial No. 315000001 and Up Operator's Manual Setup This product complies with all relevant European directives. For details, please see the Declaration of Incorporation (DOI) at the back of this publication.
- Page 2 G028063 G028062 Figure 3 Figure 2 1. Roller sets 3. Carrier frame 1. Recessed bumper 2. Washer-head self-tapping 2. Ball socket 4. Pull frame screw 2. Slide the tri-roller under the traction unit pull frame while hooking the lift roller onto the lift arm (Figure Adjusting the Rear Roller Scrapers...
- Page 3 4. When mounting the Tri-Roller Kit to the Greensmaster 3050, 3100 or 3150 traction unit, use the small diameter ball stud and washer on each end of the tri-roller (Figure 7). Adjust the links so that they are forward as far as they will go. Note: To avoid tri-roller interference with the traction pedal linkage, it may be necessary to lower the tri-rollers when the reels are in the transport position;...
-
Page 4: Installing The Rear Weight
5395:2013 when 19.5 kg (43 lb) of calcium chloride ballast is added to the rear wheel, and it is equipped with a rear weight kit. Contact your Authorized Toro Distributor for more information. Important: If a puncture occurs in a tire with calcium... -
Page 5: Operation
Maintenance Operation Training Period Lubricating the Tri-Roller Before rolling greens with the tri-roller attachments, find a There are 4 grease fittings on each tri-roller which must be clear area and practice starting, stopping, raising, lowering, lubricated after every 15 hours of operation. Lubricate using and rolling with the tri-roller. - Page 6 The method of transmission shall be electronic transmittal. This machinery shall not be put into service until incorporated into approved Toro models as indicated on the associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in conformity with all relevant Directives.
- Page 7 The Way Toro Uses Information Toro may use your personal information to process warranty claims, to contact you in the event of a product recall and for any other purpose which we tell you about. Toro may share your information with Toro's affiliates, dealers or other business partners in connection with any of these activities. We will not sell your personal information to any other company.
- Page 8 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact the Toro importer.