Sealey LED013 Instruction Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL
REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE
PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL
INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
1.1. GENERAL
Ensure the lamp is fully charged before initial use.

DO NOT turn the lamp on when it is being charged.

DO NOT shine directly into your, other person's or

animal's eyes.
DO NOT allow children to use the lamp.

DO NOT handle or move the lamp whilst it is being

charged.
DO NOT use the lamp if you suspect that the battery or

the lamp casing is damaged.
DO NOT leave battery in a discharged state, recharge

battery immediately. Before storage, fully recharge the
battery, subsequently recharge the battery at least once
every six months of non-use.
1.2. ELECTRICAL SAFETY FOR USE OF CHARGER.
USE ONLY THE SUPPLIED CHARGER PLUG FOR
CONNECTING TORCH TO THE POWER SUPPLY.
WARNING! It is the user's responsibility to read,

understand and comply with the following electrical
instructions:
You must ensure the risk of electric shock is minimised
by the installation of appropriate safety devices.
An RCCB (Residual Current Circuit Breaker) should be
incorporated in the main distribution board. We also
recommend that an RCD (Residual Current Device) is
used with all electrical products, particularly portable
equipment which is plugged into an electrical supply not
protected by an RCCB.
You must also read and understand the following instructions
concerning electrical safety.
1.2.1. The Electricity At Work Act 1989
requires all portable electrical appliances, if used on
business premises, to be tested by a qualified electrician,
using a Portable Appliance Tester (PAT), at least once a
year.
1.2.2. The Health & Safety at Work Act 1974 makes owners
of electrical appliances responsible for the safe condition
of the appliance and the safety of the appliance operator.
If in any doubt about electrical safety, contact a
qualified electrician.
1.2.3. You must ensure that you:
Inspect the charger plug, cable and connector for wear

and damage to ensure items are safe before connecting
to the mains power supply.
If worn or damaged DO NOT use.
Important: Check that the voltage marked on the charger

plug is the same as the power supply to be used.
Uncoil the cable between charger and the lamp.

DO NOT pull the charger plug from the mains socket by

the lead.
WARNING! DO NOT use any other type of charger

with this product, other than the supplied mains or
car charger. Failure to observe this warning could
result in injury and or fire and will invalidate the
warranty.
DO NOT try to take the charger plug apart.

INSTRUCTION MANUAL FOR:
CORDLESS 36LED RECHARGEABLE
INSPECTION LAMP
MODEL No's.
DO NOT use the charger plug to charge or power any

other electrical item.
DO NOT get the charger wet, or use in wet, damp

conditions (for indoor use only).
1.3 Battery Safety
WARNING! To reduce the risk of burns or fire:

DO NOT Attempt to open, disassemble, modify or

service the battery pack.
DO NOT Crush, puncture, short external contacts or

dispose of in fire or water.
DO NOT Expose to temperatures above 60°C (140°).

Replace only with the battery pack designated for this

product.
Recycle or dispose of used battery as stipulated by local

regulation.
If the electrolyte in the cells gets on your skin, thoroughly

wash with soap and water. If it gets in your eyes, rinse
thoroughly with cool water and seek immediate medical
attention.
2. INTRODUCTION / SPECIFICATION
Robust inspection lamp with lightweight Lithium-ion battery
suitable for the professional user. Incorporates 36 super bright
LED's ideal for use in engine bays and under-body inspection.
For hands-free applications features both, fold-away 360° swivel
hanging hook and an integral magnet.
Battery: ............................................................. 7.4V / 1Ah Li-ion
Charging Time: .....................................................................4hrs
Operating Time: ....................................................................5hrs
Operating Temp: ...................................................... -5°C ~ 45°C
Storage Temp: ....................................................... -20°C ~ 40°C
3. CHARGING
IMPORTANT WARRANTY INFORMATION:

The battery fitted to this lamp is considered to be a
consumable item and its ability to accept charge will
reduce over time. We will warranty it against mechanical
and electrical defect for a period of one year - this does
not cover fair wear and tear. If the battery is not properly
charged before first use, or regularly conditioned, its
capacity will diminish. Under these circumstances we will
not replace the battery even if it is less than one year old.
3.1 Connect the charger into the charge socket on the
lamp. Plug into power supply and turn on, the red
charge LEDs on the lamp (Fig.1) will light to show
charging has commenced.
3.2 When the battery has fully charged (approx 4hrs) the
red LEDs will go out and green LED's will come
on. Disconnect from mains supply.
3.3
During usage, when the battery is low the red
charging LED's will start to flash. When this happens
switch off the lamp and re-charge.
Note: The Lithium battery does not suffer from memory
effect and once fully charged may be stored for up to
six months without another charge.
Original Language Version
LED013
LED013 Issue: 3 - 22/12/11