Pakon F-335 Series User Manual
  1. Manuals
  2. Brands
  3. Pakon Manuals
  4. Scanner
  5. F-335 Series
  6. User manual

Pakon F-335 Series User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

F-335 Series
User Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the F-335 Series and is the answer not in the manual?

Questions and answers

Related Manuals for Pakon F-335 Series

Summary of Contents for Pakon F-335 Series

  • Page 1 F-335 Series User Manual...

  • Page 2: Scanner Specifications

    5.5mm outer diameter, 2.1 mm inner diameter Contents of Box • F-335 Film Scanner • 6ft. USB 2.0 Cable • Software and User Manual CD • Power suppy and power cord Size • 17.3”W x 13.6”H x 12.6”D with cover on Pakon Part#125384-A February 9, 2005...

  • Page 3: Light Source

    35mm DX codes are read using the ISO 1007 specifications and are used by the host manager. • APS encoding will only be read by a full roll of film, and will not be read from an APS strip. Pakon Part#125384-A February 9, 2005...
  • Page 4 3. Connect the USB 2.0 cable to the back of the scanner. 4. Connect the USB 2.0 cable to the back of the computer, in a USB 2.0 port. Do not plug in to a USB 1.0 connector! Pakon Part#125384-A February 9, 2005...
  • Page 5 5. While the computer is on and Windows 2000 is loaded, turn the scanner power switch into the ‘on’ position. 6. The install will ask for authorization to install the driver despite it not having been “digitally signed.” Yes must be selected for the driver to install. Pakon Part#125384-A February 9, 2005...

  • Page 6: Bios Configuration

    8. As a final step, it is recommended that the installer clean the F-335 from any dust that may be inside the scanner. Please refer to these procedures in the “Operator Maintenance” chapter. BIOS Configuration The following BIOS options are used on systems configured by Pakon, and are recommended to be configured as outlined below. Option...

  • Page 7: Hard Disk Configuration

    2. Click on “Disk Management” to begin configuring the drives. 3. Right-click on the un-allocated space on disk 1, which should be the secondary master drive. 4. The “Create Partition Wizard” will open. Click “Next” to begin. Pakon Part#125384-A February 9, 2005...
  • Page 8 6. Use the full size of the drive, unless making a Disaster Recovery partition. A “Disaster Recovery” partition is used by Pakon, to back-up the C:\ to make a system recovery option available. If no system back-up drive will be used, use the full size of the secondary drive for the scanne buffer drive.
  • Page 9 7. Assign this drive to be N:. Select N: and click “Next.” 8. It is imperative to NOT format this partition. Select “Do not format this partition.” 9. Review the settings on the new drive, to finish click “Next.” Pakon Part#125384-A February 9, 2005...
  • Page 10 10. Verify that the Disk Management screen looks correct before closing the program. Pakon Part#125384-A February 9, 2005...

  • Page 11: Operational Information

    The F-335C scanner has the ability to scan film from an APS cartridge without having to manually remove the film from the cartridge. 1. Open the MOF door by pressing down on the button to the right of the door itself. Pakon Part#125384-A February 9, 2005...
  • Page 12 2. Insert the cartridge with the film door facing the film track entrance. Pakon Part#125384-A February 9, 2005...
  • Page 13 The film gate opens and closes depending on the size of the film being scanned. It will open for 35mm film and close for APS film. This gate will open or close automatically when a different film size is selected. Pakon Part#125384-A February 9, 2005...

  • Page 14: Led Indicator Lights

    •Use a lint-free cloth daily to clean the cover of the scanner and the surface of the table it is positioned on. •Clean or replace the air filter on the back of the scanner once per week. Pakon Part#125384-A February 9, 2005...

  • Page 15: Operator Maintenance

    Cleaning the Illumination with Compressed Air 1. Turn off the scanner. 2. Disconnect the USB and power cables. 3. Gently remove the side panel of scanner, by pulling back on it. It should snap out of place. Pakon Part#125384-A February 9, 2005...
  • Page 16 ATTENTION : ne touchez aucun élément interne du scanner lorsque ce dernier est sous tension. Le couvercle est ouvert pour permettre d'éliminer poussière et débris du scanner. 4. Connect power to the scanner. 5. Turn the scanner on. 6. Remove the small film path cover. Pakon Part#125384-A February 9, 2005...
  • Page 17 2. Gently remove the side cover. 3. Using a long cotton swab, dabbed in isopropyl alcohol, clean the illumination bar inside the film track assembly. 4. The illumination bar is a small piece of glass, sitting upright. Pakon Part#125384-A February 9, 2005...
  • Page 18 Bauteile an der Rückseite des Scanners sind heiß und dürfen daher nicht berührt werden. ATTENTION : ne touchez rien d'autre que le module ventilateur et filtre. De nombreux éléments situés à l'arrière du scanner sont chauds, évitez de les toucher. Pakon Part#125384-A February 9, 2005...
  • Page 19 7. Pull straight back on the plastic fan cover until it comes free from the scanner housing. 8. Remove the filter from inside the cover, and rinse with tap water; replace if necessary. Replace the filter only after it has dried completely. Pakon Part#125384-A February 9, 2005...
  • Page 20 3. Position the tip of the compressed air hose on both sides of the film track exit, and blow. 4. After cleaning the film track, run the ‘Film Track Test’ in the client interface program. 5. Verify the scanner is properly reading DX codes by scanning a roll of film. Pakon Part#125384-A February 9, 2005...
  • Page 21 APS films. 1. Remove the film guide assembly piece shown below: 2. Pinching the tab on both sides of the film guide assembly. 3. This will expose the MOF heads on the scanner. Pakon Part#125384-A February 9, 2005...

  • Page 22: Exterior Surface Cleaning

    Clean surfaces with lint-free cloths or mild, non-abrasive spray type cleaners, where the cleaner is sprayed onto the cleaning cloth and not directly onto the equipment. Perform this type of cleaning only with the equipment disconnected and powered down. Pakon Part#125384-A February 9, 2005...

  • Page 23: Regulatory Information

    Operation of this equipment in a residential area is likely to cause harmful interfer- ence in which case the user will be required to correct the interference at his own expense. Note: Taiwan: Pakon Part#125384-A February 9, 2005...
  • Page 24 Ventilation A 4” clearance above and behind the scanners venti- lation duct is necessary Lighting <1000 LUX ambient light Noise < 70db(A) Shipping and Storage Conditions Temperature: -13 to 140 degrees Fahrenheit Humidity: 30%-90% (non-condensing) Pakon Part#125384-A February 9, 2005...

Table of Contents