Advertisement
Advertisement
Table of Contents
Related Manuals for Pakon F-135
Summary of Contents for Pakon F-135
- Page 1 F-135 F-135 Plus User Manual...
-
Page 2: Scanner Specifications
17.15cm x 21.6cm x 37.5cm (H x W x D) Resolutions The F-135 has two supported resolutions: 4Base 1000 x 1500 8Base 1500 x 2250 The F-135 Plus has three supported resolutions: 4Base 1000 x 1500 8Base 1500 x 2250 16Base 2000 x 3000 Pakon Part#125307-B... -
Page 3: Light Source
Film Types and Variations • The F-135 is designed to scan 35 MM. color negative film. 35 MM. cut strips are supported in sizes from 3 frames to 40 frames. However, to ensure DX code reading, the strips must be a minimum of 4 frames. - Page 4 Installing the F-135 The F-135 is a peripheral device. It must be connected to a computer that meets the required spec- ifications listed on page 1 of this manual. 1. Install the software for the F-135, if it is not already installed on the PC.
- Page 5 9. The process will repeat twice before finishing. 10. After the driver is finished installing, verify that the scanner driver is properly installed, by viewing the scanner properties in the Device Manager under the heading, “Imaging Devices.” Pakon Part#125307-B October 10, 2006...
-
Page 6: Bios Configuration
11. Clean the F-135 from any dust that may be inside the scanner. Please refer to these procedures in the “Operator Maintenance” chapter. BIOS Configuration The following BIOS options are used on systems configured by Pakon, and are recommended to be configured as outlined below. -
Page 7: Operational Information
Operational Information Powering On Power on the host PC, and allow it to finish loading Windows before turning the F-135 scanner on. This will ensure that the scanner can properly communicate with the host computer. Operation and Film Insertion When scanning film, do not load film until the film status LED is green. -
Page 8: Led Indicator Lights
•When the scanner is turned off, cover it with a plastic, or lint-free cover. •Use a lint-free cloth daily to clean the cover of the scanner and the surface of the table it is positioned on. Pakon Part#125307-B October 10, 2006... -
Page 9: Operator Maintenance
3. After cleaning the film track, run the ‘Film Track Test’ in the client interface program. Cleaning the Scanner Cover 1. Aim the hose of a can of compressed air into the film path--blowing the air away from the film entrance. Pakon Part#125307-B October 10, 2006... - Page 10 2. On the film exit side, blow the air away from the film exit. Pakon Part#125307-B October 10, 2006...
-
Page 11: Service Policy
This writing constitutes the final, complete and exclusive expression of the terms of warranty and remedy as agreed to by the parties to this sale. Pakon, Inc. neither authorizes nor adopts any state- ment made by any representative which differs from the terms of this writing, and all such state- ments are superseded by this document. -
Page 12: Warranty
30 day labor warranty period. This warranty does not apply to (1) to any expendable parts, (2) to any Pakon product or compo- nent which as been repaired or altered with parts or by persons not approved in writing by Pakon, Inc. -
Page 13: Contacting Technical Support
A sample image, if helpful. • Your company name and location. • Details on the problem and what has been attempted so far to resolve the problem. Pakon Contact Information Phone: Within the United States - 877.217.2566 Outside the United States - 952.936.4390 Email: support@pakon.com... -
Page 14: Regulatory Information
15-29 degrees Celsius Humidity 30-75% (non-condensing) Vibration Not to Exceed 0.05G RMS 5-200Hz Ventilation A 4” clearance above and behind the scanners venti- lation duct is necessary Lighting <1000 LUX ambient light Noise < 70db(A) Pakon Part#125307-B October 10, 2006... - Page 15 Shipping and Storage Conditions Temperature: -25 to 60 degrees Celsius Pakon Part#125307-B October 10, 2006...
Need help?
Do you have a question about the F-135 and is the answer not in the manual?
Questions and answers