Package Contents; Markings On Tool; Description (Fig. A) - DeWalt XR LI-ION DCD780 Original Instructions Manual

u
Charge only between 4 ˚C and 40 ˚C.
v
Only for indoor use.
x
Discard the battery pack with due care for
the environment.
y
Charge D WALT battery packs only with designated
e
D WALT chargers. Charging battery packs other than
e
the designated D
e
charger may make them burst or lead to other
dangerous situations.
z
Do not incinerate the battery pack.
B
USE (without transport cap). Example: Wh rating
indicates 108 Wh (1 battery with 108 Wh).
A
TRANSPORT (with built-in transport cap). Example: Wh
rating indicates 3 x 36 Wh (3 batteries of 36 Wh).
Battery Type
The following tools operate on a 18 volt battery pack:
DCD780, DCD785.
These battery packs may be used: DCB181, DCB182, DCB183,
DCB183B, DCB183G, DCB184, DCB184B, DCB184G, DCB185,
DCB187, DCB189, DCBP034, DCB546, DCB547, DCB548, DCB549.
Refer to Technical Data for more information.

Package Contents

The package contains:
1 Drill/driver or 1 drill/driver/hammerdrill
1 Charger
1 Li-Ion battery pack (C1, D1, E1, L1, M1, P1, S1, T1, X1, Y1 models)
2 Li-Ion battery packs (C2, D2, E2, L2, M2, P2, S2, T2, X2, Y2 models)
3 Li-Ion battery packs (C3, D3, E3, L3, M3, P3, S3, T3, X3, Y3 models)
1 Instruction manual
• Check for damage to the tool, parts or accessories which may
have occurred during transport.
• Take the time to thoroughly read and understand this manual
prior to operation.

Markings on Tool

The following pictograms are shown on the tool:
a
Read instruction manual before use.
g
Wear ear protection.
f
Wear eye protection
n
Visible radiation. Do not stare into light.
WALT batteries with a D WALT
e
Date Code Position (Fig. A)
The date code 5 , which also includes the year of manufacture,
is printed into the housing.
Example:
2021 XX XX
Year and Week of Manufacture

Description (Fig. A)


WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.
Trigger switch
1
Forward/reverse control
2
button
Torque adjustment collar
3
Gear shifter
4
Worklight
5
Intended Use
These drills/drivers/hammerdrills are designed for professional
drilling, percussion drilling and screwdriving applications.
DO nOT use under wet conditions or in the presence of
flammable liquids or gases.
These drills/drivers/hammerdrills are professional power tools.
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
• Young children and the infirm. This appliance is not
intended for use by young children or infirm persons
without supervision.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.

WARNING: Use only D
Inserting and Removing the Battery Pack
from the Tool (Fig. C)
nOTE: Make sure your battery pack
To Install the Battery Pack into the Tool Handle
1. Align the battery pack with the rails inside the tool's
handle (Fig. C).
2. Slide it into the handle until the battery pack is firmly seated
in the tool and ensure that you hear the lock snap into place.
To Remove the Battery Pack from the Tool
1. Press the battery release button
battery pack out of the tool handle.
EnGLIsh
Keyless chuck
6
Belt hook
7
Mounting screw
8
9 Bit clip
Battery pack
10
Battery release button
11
WALT battery packs and chargers.
e
1 is fully charged.
11 and firmly pull the
33