Advertisement
Advertisement
Related Manuals for Marcy ECLIPSE HG5000
Summary of Contents for Marcy ECLIPSE HG5000
- Page 1 NOTE: Please read all instructions carefully before using this product MARCY ECLIPSE HG5000 Table of Contents DELUXE HOME GYM Safety Notice Hardware Identifier Assembly Instruction Parts List Warranty Ordering Parts Model HG5000 Retain This Manual for Reference 01012014 OWNER'S MANUAL...
-
Page 2: Table Of Contents
ORDERING PARTS..................BEFORE YOU BEGIN Thank you for selecting the MARCY Eclipse HG5000 Deluxe Home Gym. For your safety and benefit, read this manual carefully before using the equipment. As a distributor, we are committed to provide you complete customer satisfaction. If you have any questions, or find there are missing or damaged parts, we guarantee you complete satisfaction through direct assistance. -
Page 3: Important Safety Notices
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. - Page 4 WARNING LABEL PLACEMENT The warning labels shown here have been placed on the Rear Stabilizer and Upper Frame. If the labels are missing or illegible, please contact customer service by email: service.international@tunturi-fitness.com for replacements. Apply the labels in the location shown.
-
Page 5: Hardware Pack
HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. - Page 6 HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
- Page 8 HARDWARE PACK...
-
Page 9: Assembly Instructions
ASSEMBLY INSTRUCTION Tools Required for Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches NOTE: It is strongly recommended that this machine be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Insert two Guide Rods (#16) into the holes on the Rear Stabilizer (#15). Secure each Guide Rod with one M10 x ¾”... - Page 10 DIAGRAM 1...
- Page 11 STEP 2 (See Diagram 2) A.) Attach the Upper Frame (#1) onto the two Guide Rods (#16). Secure it with two M10 x ¾” Allen Bolts (#78) and ∅ ¾” Washers (#92). DO NOT tighten the Bolts yet. B.) Place the Upper Frame (#1) onto the Vertical Frame (#4). Secure it with two M10 x 2 ¾”...
- Page 12 STEP 3 (See Diagram 3) A.) Attach the Front Press Base (#2) to the Upper Frame (#1). Secure it with one 6 ¾” Front Press Base Axle (#29), two Ø 1 ¼” Washers (#59), and two M10 Aircraft Nuts (#91). B.) Attach the Front Press (#3) to the Front Press Base (#2).
- Page 13 DIAGRAM 3...
- Page 14 STEP 4 (See Diagram 4) A.) Attach the Seat (#32) to the Seat Post (#6). Secure it with two M8 x 1 5/8” Allen Bolts (#86) and Ø 5/8” Washers (#88). B.) Insert the Seat Post into the opening on the Seat Support Frame (#7). Thread the Lock Knob (#40) into the hole on the Seat Support Frame to lock the Seat at selected height.
- Page 15 STEP 5 (See Diagram 5) A.) Slide the Right Butterfly (#10) onto the right axle on the Butterfly Base (#13). B.) Insert the Butterfly Handle (#9) into the pivot on the Right Butterfly. Secure it with one M10 x ¾” Allen Bolt (#78) and ∅ 1 ¼” Washer (#59) from the bottom. C.) Repeat Procedures A and B above to install the other side.
- Page 16 CABLE LOOP DIAGRAM...
- Page 17 STEP 6 (See Diagram 6 & Upper Cable Loop Diagram) A.) Attach the 419cm Upper Cable (#33) to the opening on the front of Upper Frame (#1). Make sure the ball stopper is underneath the Frame. Attach a Pulley (#47) to the Cable.
- Page 18 DIAGRAM 6...
- Page 19 Upper Cable Loop Diagram...
- Page 20 STEP 7 (See Diagram 7 & Lower Cable Loop Diagram) A.) Attach the 416cm Lower Cable (#35) to the opening on the Leg Developer (#8). Attach a Pulley (#47) to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#84), two ∅...
- Page 21 DIAGRAM 7...
- Page 22 Lower Cable Loop Diagram...
- Page 23 STEP 8 (See Diagram 8 & Butterfly Cable Loop Diagram) A.) Clip one end of the 249cm Butterfly Cable (#34) to the open slot on the Right Butterfly (#10). B.) Draw the Cable to the open bracket on the right side of the Vertical Frame (#4). Attach a Small Pulley (#73) to the bracket C.) Secure it with one M10 x 1 ¾”...
- Page 24 DIAGRAM 8...
- Page 25 Butterfly Cable Loop Diagram...
- Page 26 STEP 9 (See Diagram 9) A.) Connect the Lat Bar (#24) to the Upper Cable (#33) with two Hooks (#37) and one Chain (#36). B.) Connect the Abdominal Strap (#70) to the Lower Cable (#35) with a Hook. C.) Connect the Shiver Bar (#19) to the Lower Cable with two Hooks and a Chain. Replace Shiver Bar with Single Handle (#68) or Ankle Strap (#69) for various exercises.
- Page 27 Step 10 (See Diagram 10) A.) Attach the two Weight Stack Covers (#74) with four 3” Sleeve (#94) to the Upper Frame (#1) and Rear Stabilizer (#15). B.) Secure them with four M10 x 3¾” Allen Bolts (#82) and four Ø ¾” Washers (#92). DIAGRAM 10...
-
Page 28: Weight Resistance Chart
WEIGHT RESISTANCE CHART HG5000 WEIGHT PLATE Station Low Pulley Lat Pull Butterfly Front Press AB Crunch Leg Developer WEIGHT PLATE Station Low Pulley Lat Pull Butterfly Front Press AB Crunch Leg Developer *Numbers are approximate. Actual weight may vary. *Value for butterfly is for each arm. Values are shown in kgs... -
Page 29: Parts List
PARTS LIST KEY NO. DESCRIPTION Q’ty Upper Frame Ø 1 ¼” Front Press Bushing Front Press Base Ø 7/8” Leg Developer Bushing ∅ 1” Bushing Front Press Vertical Frame Ø 1” Spacer Backrest Support Frame Rubber Bumper Seat Post Ø 1 ½” Spacer Seat Support Frame Ø... -
Page 30: Warranty
LIMITED WARRANTY Tunturi Fitness warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the frame and one year on all other parts and components from the date of purchase. This warranty extends only to the original purchaser. Tunturi Fitness’s obligation under this Warranty is limited to replacing damaged or faulty parts at Tunturi Fitness’s option.
Need help?
Do you have a question about the ECLIPSE HG5000 and is the answer not in the manual?
Questions and answers