Table of Contents
Advertisement
FO-165A
FO-365A
SW-H1 No. 2 Busy tone detection ON/OFF time (Upper limit).
Similarly to SW-H1 No. 1, the set value can be varied.
The upper limit can be set in the range of 650 msec to 750 msec.
SW-H1 No. 1
SW-H1 No. 2
0
0
1
1
SW-H1 No. 3 Reserved
Set to "0".
SW-H1 No. 4 Busy tone continuous sound detect time
Set detecting time busy tone for 5 seconds or 10 seconds.
SW-H1 No. 5 Reserved
Set to "0".
SW-H1 No. 6 Busy tone detect continuation sound detect
Used to select detection of the continuous sound of certain fre-
quency.
SW-H1 No. 7 Reserved
Set to "0".
SW-H1 No. 8 Busy tone detect intermittent sound detect
Used to select detection of the intermittent sound of certain fre-
quency.
SW-H2 No. 1, No. 2 Number of Busy tone pulses
Used to set detection of Busy tone intermittent sounds.
SW-H2 No. 3 Fax switching when A.M. full or PC failure
If the answering machine's memory (tape) is full and there is no
response, the machine automatically switches to Fax reception.
If answer is not made in the PC mode (PC is not on), FAX responses.
SW-H2 No. 4 ~ No. 8 Reserved
Set to "0".
SW-I1 No. 1 ~ No. 8 Reserved
Set to "0".
SW-I2 No. 1 ~ No. 8 Reserved
Set to "0".
SW-I3 No. 1 ~ No. 8 Reserved
Set to "0".
SW-I4 No. 1 ~ No. 8 Reserved
Set to "0".
SW-I5 No. 1 ~ No. 8 Reserved
Set to "0".
SW-I6 No. 1 ~ No. 8 Reserved
Set to "0".
SW-I7 No. 1 ~ No. 8 Reserved
Set to "0".
SW-J1 No. 1, No. 2 Reserved
Set to "0".
Caution
When the value which the user is not allowed to set using the soft SW is set, output to the indication or list is not performed. However, the actual
operation is performed at the set value.
(Example) Number of rings for auto receive SWD1 No. 1-No. 4
0100
1111
(4times)
(15times)
Set value
The operation is performed 15 times.
Detection range
0
150 msec - 900 msec
1
150 msec - 650 msec
0
350 msec - 900 msec
1
350 msec - 650 msec
Display" ENTER (1-5)(4)
Value when shipping
SW-J1 No. 3 Sender's phone number registration
Used to make a choice of whether the registered sender's phone
number can be changed or not. If the switch is set to "1", new regis-
tration of the sender's phone number is disabled to prevent accidental
wrong input.
SW-J1 No. 4 ~ No. 6 Reserved
Set to "0".
SW-J1 No. 7, No. 8 Ringer volume
Used to adjust ringing volume.
SW-J2 No. 1, No. 2 Reserved
Set to "0".
SW-J2 No. 3 Polling Key
If this switch is set to 1, the last of Rapid key works as polling key.
SW-J2 No. 4, No. 5 Reserved
Set to "0".
SW-J2 No. 6 ~ No. 8 Speaker Volume
Used to adjust sound volume from a speaker.
SW-J3 No. 1, No. 2 Reserved
Set to "0".
SW-J3 No. 3, No. 4 Transaction report (Communication result
printout)
It is possible to obtain transaction results after each communication.
Normally, the switch is set (No. 1: 0, No. 2: 0) so that the transaction
report is produced only when a communication error is encountered.
If No. 1 was set to "1" and No. 2 to "0", the transaction report will be
produced every time a communication is done, even if the communi-
cation was successful.
Setting No. 1 to 1 and No. 2 to 1 will disable this function. No transac-
tion report printed.
SW-J3 No. 5 ~ No. 8 Reserved
Set to "0".
SW-K1 No. 1 Entering DIAG mode by pressing SPEED key
A bit which is used in the production process only. When the SPEED
key pressed, the switch is changed from the stand-by state to the
DIAG mode.
SW-K1 No. 2 ~ No. 8 Reserved
Set to "0".
SW-L1 No. 1 ~ No. 8 Reserved
Set to "0".
SW-L2 No. 1 ~ No. 8 Reserved
Set to "0".
List
4RINGS
Value when shipping
2 – 14
Advertisement
Table of Contents
