Advertisement
Quick Links
Calibration Of The Ultima ZT1 42E
Throttle Position Sensor (TPS)
NOTE: Videos are available for the Operation and Calibration of the Ultima ZT1 42E by clicking on one of the
links below.
How to Operate the Ultima ZT1 42E:
How to Calibrate the Ultima ZT1 42E Throttle Position Sensor:
INDEX:
Vehicle Control Module (VCM) Buttons: Page 1.
Pre Calibration Steps: Page 2.
Calibration Steps: Pages 3 through 8.
The VCM buttons are shown in Figure1.
HEADLIGHT
Instruction Sheet
https://youtu.be/NV9wlv-cf5k
VCM
PTO
START
FIGURE 1
1 of 8
INSTRUCTION SHEET
https://youtu.be/IUNXIiuQQGw
ECO
LOW SPEED
PRECISION
DRIVE
KEY SLOT
05.13.21
DRM
769-26105/01
Advertisement
Related Manuals for Cub Cadet Ultima ZT1 42E
Summary of Contents for Cub Cadet Ultima ZT1 42E
- Page 1 05.13.21 Calibration Of The Ultima ZT1 42E Throttle Position Sensor (TPS) NOTE: Videos are available for the Operation and Calibration of the Ultima ZT1 42E by clicking on one of the links below. How to Operate the Ultima ZT1 42E: https://youtu.be/NV9wlv-cf5k...
- Page 2 INSTRUCTION SHEET Pre Calibration Steps: 1. Park the mower on a flat level surface. Chock the rear wheels. 2. Equal air pressure and tire size is important on zero turn mowers and is especially important on the electrically powered drive motors of the ZT1 42E. Check and maintain both rear tires at 10 psi and the front tires at 20 psi. 3.
-
Page 3: Calibration Steps
NOTE: If the VCM will not accept calibration inputs, retry Steps 1 through 3. If the VCM still will not accept calibration inputs, contact your local Cub Cadet Service Dealer. FIGURE 2 Right Lap Bar “OUTWARD” Position 4. Leave the right lap bar in the “OUTWARD”... - Page 4 INSTRUCTION SHEET 5. Move the left lap bar forward until it hits a hard stop on the lap bar drive control lever stop adjustment bolt Rivnut as shown in Figure 4. 6. Press the LOW SPEED PRECISION DRIVE button. 7. Release the lap bar and allow it to return to the “NEUTRAL”...
- Page 5 INSTRUCTION SHEET 9. Place the left lap bar in the “OUTWARD” position as shown in Figure 6 and press the START button. FIGURE 6 10. The “N” on the screen should have a box around it as shown in Figure 7. FIGURE 7 769-26105/01 Instruction Sheet...
- Page 6 INSTRUCTION SHEET 11. Move the left lap bar to the “NEUTRAL” position and pull rearward until it hits a hard stop as shown in Figure 8 and press the button. NOTE: If you hold the button for more than 7 seconds, you will get an error code. FIGURE 8 12.
- Page 7 INSTRUCTION SHEET Lap Bars In The “OUTWARD” 14. For the right side lap bar calibration, proceed as follows. Position 15. Place both lap bars in the “OUTWARD” position as shown in Figure 10. FIGURE 10 16. Simultaneously press and hold the PTO the HEADLIGHT buttons for 7 seconds or until the screen displays F N R as shown in Figure 11,...
- Page 8 INSTRUCTION SHEET Left Lap Bar 17. Leave the left lap bar in the “OUTWARD” “OUTWARD” position and move the right lap bar to the inward Position “NEUTRAL” position as shown in Figure 12. 18. For the completion of the right lap bar calibration, repeat Steps 5 through 13, then proceed to Step 19.