MIMAKI JV300-130 Maintenance Manual page 205

MAINTENANCE MANUAL > Troubleshooting > Details on Errors and Malfunctions > List of Error Messages
Model JV300-130/160 Issued 2014.05.30 Revised
7.1.2 List of Error Messages
 List of Error Messages (5/7)
No. LCD
ERROR 50f
48
L-SCALE BLACK
ERROR 529
49
LEnc.Count HPC[____]
ERROR 52a
50
LEnc.Count HDC[____]
ERROR 516
MEDIA SET POSITION L
51
ERROR 516
MEDIA SET POSITION R
ERROR 528
PUMP MOTOR SENSOR
52
ERROR 602
CARTRIDGE END
53
ERROR 608
WRONG INK IC
54
ERROR 612
55
INK LVL LOW
ERROR 613
INK LVL END
56
ERROR 614
Preservation Failure
57
ERROR 627
RE-INSERT CARTRIDGE
58
ERROR 628
WRONG INK CARTRIDGE
59
© 2014 MIMAKI ENGINEERING CO.,LTD.
Cause
Liner Scale error
Difference of linear scale value (HPC1 and
HPC2)
Difference of linear scale value (HDC and
HPC2)
The media is set outside the range.
Detecting error of pump sensor
Ink end
(Non of printing, ink use-up cleaning is only
allowed.)
IC chip of Ink cartridge unreadable property.
When 600ml cartridge is used,
ink amount of the cartridge is less than 60ml.
When 600ml cartridge is used,
ink amount of the cartridge is less than 25ml.
When 600ml cartridge is used, writing to the
IC chip is failed at the time of weight
registration.
The cartridge has not been set for a certain
amount of time.
An error occurred in the IC chip information of
the ink cartridge.
F/W ver 1.10 Remark
List of Countermeasures
1. Check the assembly position of Linear Scale and
Encoder PCB Assy..
2. Check Linear Scale (scratches or dirtiness or so.)
3. Replace the Linear Scale with a new one.
4. Replace the Encoder PCB Assy. with a new one.
(Refer to 6.4.8)
1. Check the media setting position.
2. Perform cleaning of the media width sensor.
3. Execute [#TEST PAPER SENSOR].
1. Perform [#TEST][SENSOR][PUMP MOTOR], and con-
firm pump operation and sensor reaction by pressing
[FUNC] key.
2. Replace the sensor.
3. Replace the suction pump.
(When the message is still displayed even after a new Ink
Cartridge or an empty Ink Cartridge is charged;)
1. Perform and confirm [#TEST][SENSOR][CartridgeSen-
sor]. (The number correspond to the cartridge number.)
2. Check the peripheral and the assembly of near end sensor.
3. Check the connection of theD contact PCB Assy. and near
end sensor.
4. Replace the cartridge.
5. Replace the ID contact PCB Assy. and near end sensor with
new one.
6. Replace the CART IO PCB with a new one.
7. Replace the MAIN PCB with a new one.
3.3.1)
1. Check the attached status of the chip.
2. Perform and confirm [#TEST][CHECK INK IC].
3. Replace the ID contact PCB Assy. with new one.
1. Register weight of the cartridge.
2. Replace the cartridge and ink IC with a new one.
3. Perform and confirm [#TEST][CHECK INK IC].
4. Check the connection of theD contact PCB Assy.
5. Replace the ID contact PCB Assy. with new one.
6. Replace the CART IO PCB with a new one.
1. Replace the cartridge.
2. Perform and confirm [#TEST][CHECK INK IC].
3. Check the connection of theD contact PCB Assy.
4. Replace the ID contact PCB Assy. with new one.
5. Replace the CART IO PCB with a new one.
Set the cartridge.
1. Check that the cartridge has been inserted correctly.
2. Check the sensor operation with
[#TEST][SENSOR][CartridgeSensor].
The chip was used too much (exceeding the specified times).
1. Check whether the chip was also replaced when the pack
was replaced.
2. Check the W ink nozzle clogging and resolve it.
3. Replace the IC chip with new one.
Rev.
1.0
1
2
3
4
(Refer to
5
6
7
8
7.1.2 R.1.0 P.5