Advertisement
Advertisement
Related Manuals for baxter DOSEEDGE
Summary of Contents for baxter DOSEEDGE
- Page 1 Setting Up the PrepStation Cart M00205 v1.1...
-
Page 2: Table Of Contents
Table of Contents TABLE OF CONTENTS UNPACKING THE PREPSTATION CART AND COMPONENTS............1 SETTING UP THE CART ......................2 SETTING UP THE TOUCHSCREEN AND CABLES ................3 SETTING UP THE PRINTER ......................6 Setting Up the Zebra Printer ....................6 Setting Up the Epson Printer .................... -
Page 3: Unpacking The Prepstation Cart And Components
Unpacking the PrepStation Cart and Components UNPACKING THE PREPSTATION CART AND COMPONENTS 1. Remove all parts from the carton. NOTE: The cable guide is not shown. 2. Unpack all components, power cables and connecting cables: • Uninterruptible power supply (UPS) •... -
Page 4: Setting Up The Cart
Setting Up the PrepStation Cart SETTING UP THE CART 1. Remove the cover from the box at the base of the cart. 2. Insert the UPS in the rear compartment of the box. Thread the power cable through the hole in the base. -
Page 5: Setting Up The Touchscreen And Cables
Setting Up the Touchscreen and Cables SETTING UP THE TOUCHSCREEN AND CABLES 1. Align the touchscreen supports with its brace on the cart. Insert and tighten 4 screws. Tip! Install the top screws first. 2. Place the power supply units for all components in the front compartment of the power box. - Page 6 Setting Up the Touchscreen and Cables 5. Insert the cable guide in the top of the tower until it pokes out the bottom. 6. Snag the cords with the cable guide. Tip! Pull all cords together at one time. Pulling the cords individually is more difficult.
- Page 7 Setting Up the Touchscreen and Cables 7. Draw the cable guide through the tower until the cords are amply threaded through the opening. Tip! It is better to have too much available cord than too little. 8. Tilt the touch-screen up. Connect the power cord or USB cable (depending on model) to the monitor.
-
Page 8: Setting Up The Printer
Setting Up the Printer SETTING UP THE PRINTER SETTING UP THE ZEBRA PRINTER 1. Place the printer on the platform. Connect the power cord (threaded through the post) to the printer. 2. Connect the USB or parallel cable (depending on model) to the printer, and then to the touchscreen. -
Page 9: Setting Up The Epson Printer
Setting Up the Printer SETTING UP THE EPSON PRINTER 1. Place the printer on the platform. Connect the power cord (threaded through the post) to the printer. 2. Connect the cable to the printer, and then to the touchscreen. SETTING UP THE PREPSTATION CART M00205 v1.1 Page 7... -
Page 10: Setting Up The Other Components
Setting Up the Other Components SETTING UP THE OTHER COMPONENTS 1. Connect the scanner to the touchscreen. 2. Place the scanner in its holder, then position the scanner in the hood. SETTING UP THE PREPSTATION CART M00205 v1.1 Page 8... - Page 11 Setting Up the Other Components 3. Connect the camera stand cable to the touchscreen. 4. Install the lens on the camera. Attach the camera to the camera stand. SETTING UP THE PREPSTATION CART M00205 v1.1 Page 9...
- Page 12 Setting Up the Other Components 5. Connect the cable to the camera. Position the camera and stand in the hood. 6. Connect the footpedal (optional) to the touchscreen. Position the footpedal where desired. 7. Optional: Connect the power cord to the scale, then connect the USB cable from the scale to the touchscreen.
- Page 13 Setting Up the Other Components 9. Replace the cover on the box. 10. Roll the cart into position. SETTING UP THE PREPSTATION CART M00205 v1.1 Page 11...
- Page 14 Error! Reference source not found. Baxter and DoseEdge are trademarks of Baxter International Inc. or its subsidiaries. All other trademarks, brands or product images appearing herein are the property of their respective owners.
Need help?
Do you have a question about the DOSEEDGE and is the answer not in the manual?
Questions and answers