Operation - DeWalt XR LI-ION DCMPS567 Original Instructions Manual

one hand as shown in Fig. N. Use your other hand to loosen the
threaded sleeve and then pull the two halves apart. Repeat this
process if the center extension was attached.
Attaching and Adjusting the Shoulder Strap
(Fig. O)
This pole saw comes with an adjustable shoulder strap.
1. Snap the shoulder strap latch
as shown in Fig.O.
2. Adjust the strap so it fits securely over your shoulder.

OPERATION

Instructions for Use

WARNING: Always observe the safety instructions and
applicable regulations.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
Proper Hand Position (Fig. P)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the main handle
and one hand on the foam gripper
Operating the Pole Saw (Fig. A)

WARNING: Read and understand all instructions. Failure
to follow all instructions listed below may result in electric
shock, fire and/or serious personal injury.

CAUTION: Always reduce the tension off the chain again
after finishing work. The chain contracts as it cools down.
If it is not slackened off, it can damage the pole saw.
IMPORTANT: Never operate a pole saw that is damaged or
improperly adjusted or that is not completely and securely
assembled. Be sure that the saw chain
the trigger switch is released. Never adjust the guide bar
or saw chain when the motor is operating or the battery
is attached.
Pole Saw Trimming/Pruning

WARNINGS:
Never stand directly under the limb you are cutting.
•
Always position yourself out of the path of falling debris.
• Always wear head, eye, foot and body protection.
Wearing body protection helps reduce the risk of injury when
operating this unit.
• Never stand on a ladder or other unstable support while
using the pole saw. Always avoid any position which can
cause you to loose your balance and cause severe injury.
onto the strap mount
28 19
29
7 .
14 stops moving when
13
Keep other persons at least 15 m from the work area.
•
Distractions can cause you to lose control.
• Electrocution Hazard. To prevent shock, do not operate
within 15 m of overhead electrical lines. Always check
surrounding area for hidden electrical lines.
• Do not extend pole saw switch handle above
shoulder height.
On/Off Switch (Fig. Q)
Always be sure of your footing and grip the pole saw firmly with
both hands with the thumb and fingers encircling the handle.
To turn the tool ON pull the lock button
thumb and then squeeze the trigger switch
as shown in Fig. Q. (Once the tool is running you can release the
lock button.) To turn the tool OFF, release the trigger.
Branch Removal Hook (Fig. A)

CAUTION: The branch removal hook is not a belt hook.
Your pole saw includes a branch removal hook
intended purpose of helping to remove small to moderately sized
pruned branches.
Pruning With the Pole Saw (Fig. A, P, R)

WARNING: Let the tool work at its own pace. Do
not overload.

WARNING: When pruning trees: guard against kickback
which can result in severe injury or death. See guard
Against Kickback, to avoid the risk of kickback. Do not
overreach. Make sure your footing is firm. Keep feet apart.
Divide your weight evenly on both feet.
1. Use both hands to grip pole saw as shown in Fig. P. Use a
firm grip. Thumbs and fingers must wrap around pole saw
handle and pole. Keep fingers away from sawdust exhaust
chute shown in Fig. R.
26
2. Never operate while in a tree, in any awkward position or on
a ladder or other unstable surface. You may lose control of
pole saw causing severe injury.
3. Follow directions below to trim a tee.
a. Make sure pole saw is running at full speed before
making a cut. When starting a cut, place moving saw
chain against limb. Hold pole saw firmly in place to
14
avoid possible bouncing or skating (sideways movement)
of pole saw.
b. Guide pole saw using light pressure. Make first cut
152 mm from tree trunk on underside of limb. Use top of
guide bar 13 to make this cut. Cut 1/3 through diameter
of limb. Then make the finish cut from the top. If you try
to cut off thick branches from the bottom, the branch
may close in and pinch the saw chain in the cut. If you try
to cut off thick branches from the top, without a shallow
undercut, the branch may splinter. Do not force pole saw.
The motor will overload and can burn out. It will do the
job better and safer at the rate for which it was intended.
c. Remove pole saw from cut while it is running at full
speed. Stop pole saw by releasing trigger switch
English
back with your
5
4 with your fingers
18 for the
4 .
17