Cosen MH-1016JA Instruction Manual
  1. Manuals
  2. Brands
  3. Cosen Manuals
  4. Saw
  5. MH-1016JA
  6. Instruction manual

Cosen MH-1016JA Instruction Manual

Horizontal bandsaw with variable step pulley
Hide thumbs
Table of Contents

Advertisement

Quick Links

Bandsaw Specialist
Instruction Manual
KC1016W
KC1016VS/
Model: MH-1016JA/MH-1018JA
Manual Horizontal Bandsaw
with Variable Step Pulley
Ma nua l
Cosen Mechatronics Co., Ltd.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MH-1016JA and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Cosen MH-1016JA

Summary of Contents for Cosen MH-1016JA

  • Page 1 Bandsaw Specialist Instruction Manual KC1016W KC1016VS/ Model: MH-1016JA/MH-1018JA Manual Horizontal Bandsaw with Variable Step Pulley Ma nua l Cosen Mechatronics Co., Ltd.
  • Page 2 MH-1016JA/MH-1018JA. TECHNICAL ADVICE/ SPARE PARTS  Please contact the COSEN-representative in your local area in case you need any technical advice or if you want to order spare parts. Instruction Manual: MH-1016JA/MH-1018JA Manual Horizontal Bandsaw with Variable Step Pulley Ver.
  • Page 3 However, if there are questions, please contact our agent or our factory for the nearest service or sales representative. Enough, already. I hope you find COSEN as incredibly smart as I do. If you have any suggestions for improvement, please tell us, we will appreciate your help.
  • Page 4 TABLE OF CONTENTS SECTION PAGE SAFETY RULES 1-1~8 GENERAL INFORMATIONS INTRODUCTION EQUIPMENT DESCRIPTION 2.2.1 Specification 2-2~3 2.2.2 Identification of Main Parts & Terminology 2-4~7 2.2.3 Emergency Stop Button 2.2.4 Noise Level 2.2.5 Safety Devices and Guards 2.2.6 Specification of Electrical Equipment 2-10 GUIDE TO THE MANUAL 2-10...

  • Page 5: Table Of Contents

    TABLE OF CONTENTS ELECTRICAL CIRCUIT DIAGRAMS 5-1~4 BAND SAW CUTTING A PRACTICAL GUIDE INTRODUCTION BAND SAW BLADE SELECTION 6-1~3 Some Sawing Practices 6.3.1 Selection of Saw Pitch 6.3.2 Material Size and Saw Pitch 6-4~5 MAINTENANCE & SERVICE INTRODUCTION BASIC MAINTENANCE MAINTENANCE SCHEDULE Before beginning of work each day After ending work each day...
  • Page 6 Section 1 SAFETY RULES...
  • Page 15 Section 2 GENERAL INFORMATION...
  • Page 16 GENERAL INFORMATION Section 2 SECTION 2 GENERAL INFORMATION I : FOR MACHINE COMMON 2.1 INTRODUCTION This automatic band saw is a model more popular than any other model as witnessed in many countries worldwide. This machine was developed by a group of R&D engineers over a considerable period of time assuring you of the highest efficiency and performance.
  • Page 17 GENERAL INFORMATION Section 2 2.2.1 Specifications Specification of The Machine MODEL MH-1016JA 250mm (10") MAX. CAPACITY (W×H) 230 × 230 mm (9" × 9") (W×H) 230 × 370 mm (9" × 14.5") 19, 31, 48, 78M/min. 50Hz 62, 102, 157, 256ft/min) SPEED 23, 37, 58, 93M/min.
  • Page 18 GENERAL INFORMATION Section 2 Specification of The Machine MODEL MH-1018JA 255 mm (10", 90°) 255 mm (10", 45°) (W×H) 230 × 230 mm (9" × 9") 230 × 230 mm (9" × 9") MAX. CAPACITY (W×H) 230 × 460 mm (9" × 18") 230 ×...
  • Page 19 GENERAL INFORMATION Section 2 2.2.2 Identification of Main Parts & Terminology MH-1016JA FIG 2-1 TOP VIEW OF THE MACHINE(MH-1016JA) FIG 2-2 FRONT VIEW DRAWING (MH-1016JA)
  • Page 20 GENERAL INFORMATION Section 2 FIG 2-3 THE SIDE VIEW OF THE MACHINE (MH-1016JA)
  • Page 21 GENERAL INFORMATION Section 2 MH-1018JA FIG 2-1 TOP VIEW OF THE MACHINE(MH-1018JA)
  • Page 22 GENERAL INFORMATION Section 2 FIG 2-2 FRONT VIEW DRAWING (MH-1018JA) FIG 2-3 THE SIDE VIEW OF THE MACHINE (MH-1018JA)
  • Page 23 GENERAL INFORMATION Section 2 2.2.3 Emergency Stop Button Your machine‘s emergency stop button is designed to be very easy to access. When you press it, it will stop the machine completely to avoid severe injury when an accident occurs. You should press it immediately without hesitation in the following cases: ...
  • Page 24 GENERAL INFORMATION Section 2 2.2.5 Safety Devices and Guards This manual show safety related components illustration as following: Safety moving element: All the major moving elements on the machine include: 1. Saw head assembly. 2. Saw wheels. 3. Saw blade guide/arm. 4.
  • Page 25 GENERAL INFORMATION Section 2 2.2.6 Specification of Electrical Equipment Electrical equipment is very important to the control system. Your machine a new type system designed for safety by our engineers. We describe briefly as follows: GROUND DIAGRAM WARNING:Before star up machine user should be inspection of power supply wiring must connected ground connection avoid event of electric stock.
  • Page 26 GENERAL INFORMATION Section 2 II : ONLY FOR MACHINE WITH “CE ” Certificated 2.5 INTRODUCTION In designing this machine, many measures have been taken to prevent personal injury. However, there still some risks remaining despite all the measure adopted. We then put protective devices at those places.
  • Page 27 GENERAL INFORMATION Section 2 Read all WARNINGS to prevent personal injury  Orange and black WARNING labels mean hazards or unsafe practices can result in severe personal injury or death. WARNING: This manual has important safety information. All users must read it before performing any activity on the machine, such as replacing the saw band or doing regular maintenance.
  • Page 28 GENERAL INFORMATION Section 2  Green and white SAFETY INSTRUCTIONS are important reminders that should be read before operating the machine. Please do not make any decisions casually without first reading all safety instructions. 2.6 RISK ASSESSMENT Risk assessment generally takes account of intended use and foreseeable misuse, including process control and maintenance requirements.
  • Page 29 Section 3 MOVING AND STALLATION...
  • Page 30 MOVING AND INSTALLATION Section 3 SECTION 3 MOVING AND INSTALLATION 3.1 INTRODUCTION Your machine is made of three main system components: Machine equipment, hydraulic system, and electrical control system. Please read the entire manual carefully to obtain a thorough knowledge of the machine. This section describes how to move and install the machine to prevent personal injuries and machine damage.
  • Page 31 MOVING AND INSTALLATION Section 3 • Apply the wire rope sling to the lifting hole at rear of the front vise slide and to the rear end of the machine. Please keep the machine balanced rear-front and left-right side when you are lifting up the machine.
  • Page 32 MOVING AND INSTALLATION Section 3 • You must apply proper forklift technique to avoid damage to the machine. • You also have to keep the machine balanced at all times. 3.3 Use rolling cylinder to place You can use this method to move your machine when it is in the small machine shop . •...
  • Page 33 MOVING AND INSTALLATION Section 3 3.3.1 Safety Precautions Read the operating manual thoroughly to avoid improper operations. Environment: Avoid exposing machine to direct sunlight. ℃ ℃ Keep the room temperature between 5 to 40 Keep the humidity of your machine at 30%-95“(without condensation) to avoid dew on electric installation and machine.
  • Page 34 MOVING AND INSTALLATION Section 3 FIG 3-1 FLOOR SPACE REQUIRED WITHOUT OPTIONAL TABLE FIG 3-2 FOUNDATION DIAGRAM...
  • Page 35 MOVING AND INSTALLATION Section 3 3.3.4 Unpacking After the machine has been properly positioned, remove the shipping bracket. Unpack your machine carefully. Do not damage the machine surface paint. Remember to remove the bracket used to lock the saw frame and the saw bed. Be sure to retain this bracket so that it can be used again in the event that your machine must be relocated.
  • Page 36 MOVING AND INSTALLATION Section 3 Machine leveling Place spirit levels on the vise slide plates and the work feed table, and adjust the left-and-right and fore-and-aft level of the machine with leveling bolts. The fore-and-aft level should be adjusted correctly. level of the rear of the machine is approximately 20 mm higher than the level of the front end.
  • Page 37 MOVING AND INSTALLATION Section 3 Hydraulic fluid supply Open the filler cap. Please fill the hydraulic oil tank with the hydraulic oil furnished with the machine. Check the sight gauge to ascertain the oil level in the tank. (Oil tank should be full already if it is a new machine that operation first time, the oil tank should be filled hydraulic oil to above 2/3 or full level.
  • Page 38 MOVING AND INSTALLATION Section 3 3.5 RESHIPMENT PROCEDURE We recommend you do the procedures as follows: 1. Turn off the power. 2. Fix the saw head. 3. Pack machine with plastic bag or soft paper to protecting it from dust. 4.
  • Page 39 Section 4 OPERATION INSTRUCTION...
  • Page 40 OPERATING INSTRUCTION SECTION 4 Section 4 OPERATING INSTRUCTION 4.1 SAFETY PRECAUTIONS For your safety, please read and understand the instruction manual before you operate the machine. The operator should always follow these safety guidelines: • The machine should only be used for its designated purpose. •...
  • Page 41 OPERATING INSTRUCTION SECTION 4 If you choose dry cutting or low-speed cutting, the chips may accumulate in machine parts and may cause operation failure or insulation malfunction. We suggest you choose wet cutting to avoid machine damage. Cutting unknown materials Before cutting an unknown material, consult the material supplier, burn a small amount of chips from the material in a safe place, or follow any other procedure to check if the material is flammable.
  • Page 42 OPERATING INSTRUCTION SECTION 4 4.3 CONTROL PANEL Control panel Power Power on Emergency Coolant Cutting pressure indicator button stop button ON/OFF control knob Control buttons A. Power indicator When the lamp is on, it indicates the power to the machine is turned on. B.
  • Page 43 OPERATING INSTRUCTION SECTION 4 Turning the knob clockwise decreases the cutting pressure. To obtain a good cutting result, choose the right cutting pressure by turning the knob Note: The machine will stop automatically when the material has been cut through. Warning: Before plugging the power cord, make sure the power on switch is turned off.
  • Page 44 OPERATING INSTRUCTION SECTION 4 4.4 Cutting Operations Warning: Do not connect power cord to power source until the following instructions are clearly understood and followed. Selecting Blade Speed Blade speed selection should be made according to the material being cut. The following chart provides information on blade speed and is used for reference only.
  • Page 45 Changing Blade Speed – for variable stepless pulley drive (optional) Infinitely variable blade speed is easily achieved with this optional device. Cosen’s variable stepless pulley drive assembly allows the operator to select the optimum speed for best performance in all cutting applications.
  • Page 46 OPERATING INSTRUCTION SECTION 4 Adjusting Feed Rate (Cutting Pressure) To obtain desired feed rate (cutting pressure), the “hydraulic cylinder” (Fig 3, #4) and “feed pressure spring” (Fig 3, #6) are to be adjusted together. 1. Saw bow 2. By-pass valve (Do not make adjustment here.) 3.
  • Page 47 OPERATING INSTRUCTION SECTION 4 Adjusting Vise Caution: Always use the vise to clamp the work. Never hand-hold the work for cutting. Clamp material securely by turning the vise hand wheel clockwise. Angle Cutting The vise offers the user great flexibility in angle cutting from 0 ° (Position 1) to 45 ° (Position 2). Cutting at 45 °...
  • Page 48 OPERATING INSTRUCTION SECTION 4 1. Move the right guide arm to the end of the dovetail guide. 2. Lift the saw bow up to the highest position. 3. Loosen the two lock bolts (Fig 5, #2 and #3) of the fixed vise jaw (Fig 5, #1). Then adjust the fixed °...
  • Page 49 OPERATING INSTRUCTION SECTION 4 Installing material stop bracket 1. Install the depth bar (Fig 9, #2) and tighten the set screw. (The depth bar is taken off from the machine base during transit for safety reason. 2. Lift the saw bow and clamp material securely with vise.
  • Page 50 OPERATING INSTRUCTION SECTION 4 Unrolling & installing the blade Caution: Always wear leather gloves and protection glasses when handling a blade. Unrolling the blade Please follow the procedures illustrated below. Fig 4 – 3 Unroll and roll the blade 4-11...
  • Page 51 OPERATING INSTRUCTION SECTION 4 Changing blade Caution: Make sure the power cord is disconnected from power source. 1. Elevate the saw bow until it is positioned vertically. 2. Open the top wheel cover. 3. Release blade tension by turning the blade tension handwheel counterclockwise and remove the blade.
  • Page 52 OPERATING INSTRUCTION SECTION 4 Machine adjustments Caution: Always make sure the power cord is disconnected from power source when making adjustments. Complete Cut – Adjusting Horizontal Stop Spring Cushion The workpiece should be able to cut through completely. If it does not, please follow these steps to adjust the horizontal stop spring cushion.
  • Page 53 OPERATING INSTRUCTION SECTION 4 Troubleshooting and Adjustments Some of the uncommon problems that may be encountered in band saw cutting are described as follows with correction recommendations. A. Vibration on saw bow Cause 1: Dull blade or stripped blade Remedy: Replace a new saw blade. Cause 2: Clearance between saw blade and trust roller (Fig 11-1, #2) is too large.
  • Page 54 OPERATING INSTRUCTION SECTION 4 4-15...
  • Page 55 OPERATING INSTRUCTION SECTION 4 B. Cut-off work shows an improper slant downward Y-axis (Fig 11). Cause 1: Improper blade tension Remedy: Refer to “Adjusting blade tension.’ Cause 2: Incorrect alignment between the rollers (outer, inner) and the saw blade (Fig 11, #3, left) Remedy: 1.
  • Page 56 OPERATING INSTRUCTION SECTION 4 C. Cut-off work shows an improper tilt inward or toward X-axis (Fig 11). Cause 1: Incorrect alignment between fixed vise jaw and saw blade. Remedy: Adjust the vise so it is 90 ° to the saw blade. (See Fig 7). Replacing dovetail guide (Fig 11-5) Note: The dovetail guide has been factory-adjusted at time of manufacturer.
  • Page 57 Section 5 ELECTRICAL SYSTEM...

  • Page 58: Electrical Circuit Diagrams 5-1~4

    ELECTRICAL SYSTEM Section 5 SECTION 5 ELECTRICAL SYSTEM 5.1 INTRODUCTION This section will introduce the machine’s electric system diagram in easy understand way. 5.2 ELECTRICAL CIRCUIT DIAGRAMS As mentioned earlier at the beginning of the section. The electric circuit diagrams shown here are: The electric circuit diagram of the system : Fig 5-1 control panel layout Fig 5-2 circuit board layout...
  • Page 59 ELECTRICAL SYSTEM Section 5 Fig.5-1 control panel layout...
  • Page 60 ELECTRICAL SYSTEM Section 5 Fig.5-2 circuit board layout...
  • Page 61 ELECTRICAL SYSTEM Section 5 Fig.5-3 power supply layout...

  • Page 62: Band Saw Cuttinga Practical Guide

    Section 6 BAND SAW CUTTING A PRACTICAL GUIDE Section 7...

  • Page 63: Introduction

    BAND SAW CUTTING - A PRACTICAL GUIDE 6.1 INTRODUCTION COSEN band saw machines are designed to be installed with high quality using high speed saw blades for maximizing productivity. To be able to use this kind of high performance band saw...
  • Page 64 BAND SAW CUTTING - A PRACTICAL GUIDE Section 6 It will be slower to cut tubing than to cut solids, because the blade must enter the material twice, and because coolant will not follow the blade as well. Tough or abrasive materials are much harder to cut than their machinability rating would indicate.
  • Page 65 BAND SAW CUTTING - A PRACTICAL GUIDE Section 6 Flexible Back Weld Fig. 6.3 Electron Welded Blade A particular blade may have teeth which are too hard at the tips, causing them to break off in the material. This is most likely to happen as a result of chips wedging together in the cut. A broken tooth in the material can easily cause dulling on one side of the entire blade before it is dislodged from the cut.

  • Page 66: Some Sawing Practices

    BAND SAW CUTTING - A PRACTICAL GUIDE Section 6 6.3 Some Sawing Practices 6.3.1. Selection of Saw Pitch : Sawing “Rules of Thumb”: 1. The thinner the stock, the finer the saw pitch 2. The thicker the stock, the coarser the saw pitch 3.
  • Page 67 BAND SAW CUTTING - A PRACTICAL GUIDE Section 6 Solid Stock: STYLE up to 25 mm 25-100mm 100-250mm 1“ 1“-4” 4-10“ 8-10 TPI 6-8 TPI 3-4 TPI (Teeth per inch) Structurals: STYLE up to 10 mm 10-20mm above 20mm 3/8“ 3/8-3/4“...

  • Page 68: Maintenance & Service

    Section 7 MAINTENANCE & SERVICE...

  • Page 69: Introduction

    MAINTENANCE & SERVICE Section 7 SECTION 7 MAINTENANCE & SERVICE 7.1 INTRODUCTION For the best performance and longer life of the band saw machine, a maintenance schedule is necessary. Some of the daily maintenance usually takes just a little time but will give remarkable results for the efficient and proper operation of cutting.

  • Page 70: Every Monthly Maintenance

    MAINTENANCE & SERVICE Section 7 Every monthly maintenance. Please apply grease to the following points: 1. Idle wheel 2. Driven wheel 3. Blade tension device idle wheel Recommended Grease: Shell Alvania EP Grease 2 Mobil Mobilplex 48 Blade tension cylinder driven wheel First Three Months(TRANSMISSION OIL REPLACEMENT) Replace the transmission oil after operting for three...

  • Page 71: Terminating The Use Of The Machine

    MAINTENANCE & SERVICE Section 7 (4) Atmosphere: Use a plastic canvas to cover machine to avoid excessive dust, acid fume, corrosive gases and salt. (5) Avoid exposing to direct sunlight or heat rays which can change the environmental temperature. (6) Avoid exposing to abnormal vibration. (7) Must be connected to earth.

  • Page 72: System Trouble Shooting

    Section 8 SYSTEM TROUBLE SHOOTING...

  • Page 73: Introduction

    All the machines being manufactured by COSEN pass a 72 hours continuously running test before shipping out and COSEN is responsible for the after sales service problems during the warranty period if the machine are used normally. However, there still exist the some unpredictable problems which may disable the machine from operating.

  • Page 74: General Troubles And Solutions

    SYSTEMS TROUBLE SHOOTING Section 8 8.3 GENERAL TROUBLES AND SOLUTIONS WARNING DISCONNECT POWER CORD TO MOTOR BEFORE ATTEMPTING ANY REPAIR OR INSPECTION TROUBLE PROBABLE CAUSE SUGGESTED REMEDY Excessive belt tension Adjust belt tension so that belt does not slip on drive pulley while cutting ( 1/2“...

  • Page 75: Minor Trouble Shooting

    SYSTEMS TROUBLE SHOOTING Section 8 8.4 MINOR TROUBLES SHOOTING Item Symptom Probable Corrective Action Saw blade motor does not run a.Overload relay activated Reset even though blade drive button b.Saw blade is not at forward Depress SAW FRAME is depressed. limit position.

  • Page 76: Blade Troubles And Solutions

    SYSTEMS TROUBLE SHOOTING Section 8 8.6 BLADE TROUBLES AND SOLUTIONS WARNING DISCONNECT POWER CORD TO MOTOR BEFORE ATTEMPTING ANY REPAIR OR INSPECTION TROUBLE PROBABLE CAUSE SUGGESTED REMEDY Too few teeth per inch Use finer tooth blade Loading of gullets Use coarse tooth blade or cutting lubricant. Teeth strippage Excessive feed...

  • Page 77: Sawing Problems And Solutions

    SYSTEMS TROUBLE SHOOTING Section 8 8.7 SAWING PROBLEMS AND SOLUTIONS Other than this manual, the manufacturer also provides some related technical documents listed as follows: Sawing Problems and Solutions Vibration during cutting Failure to cut Short life of saw blade Curved cutting Broken blade Use of blade with incorrect pitch...

  • Page 78: The Adjustment Of The Feeding Table

    SYSTEMS TROUBLE SHOOTING Section 8 8.8 THE ADJUSTMENT OF THE FEEDING TABLE If the feeding table suffers the huge stroke and the alignment is effected, follow the below procedure to adjust. TOOL, measuring Measurement, Horizontal balance Procedure Screw or loosen the adjusting bolt to attain the horizontal balance (leveling) between the roller table and the machine frame.
  • Page 79 Section 9 PART LIST...
  • Page 80 MH-1016JA series PART LIST 2013/3/25...
  • Page 81 MH-1016JA series PART LIST 2013/3/25 底座組 Bed Assembly NO. PART NO. PART NAME PART NAME CHINESE Q'YT PART SPEC. M1016-10000 Bed Assembly 床面組 M1016-30000 Saw bow assembly 鋸弓組 MJA-1035 Cylinder 油壓缸組 AJC-7017A-CE Base 底座 MJA-1020 Wire rope guide wheel 鋼索導輪...
  • Page 82 MH-1016JA series PART LIST 2012/12/25...
  • Page 83 MH-1016JA series PART LIST 2013/4/2 床面組 Saw bow assembly PART NO. PART NAME Q'TY PART NAME CHINESE PART SPEC. MJA-1001 床面 MJA-1008B Joint shaft 關節軸 MJA-1010 Movable vise 活動虎鉗 MJA-1011 Fixed vise 固定虎鉗 MJA-1012 Lead screw seat 導螺桿座 MJA-1013 Lead screw ring 導螺桿固定圈...
  • Page 84 MH-1016JA series PART LIST 2012/12/25...
  • Page 85 MH-1016JA series PART LIST 2013/4/3 PART NO. PART NAME PART NAME CHINESE PART SPEC. Q'TY MJA-2001A Saw bow 鋸弓 SJY-1113 Idle wheel 上輪 PP-14130 Bearing 軸承 6205Z MAE-2025 Bearing washer 上輪軸墊圈 SJY-1114 Idle wheel shaft 上輪軸 PLA-12-40 Hexagon bolt 外六角頭螺絲...
  • Page 86 2013/5/17 PART NO. PART NAME PART NAME IN CHINESE PART SPEC. Motor 馬達 PP-31041 2HP 3φ 4P 60HZ 220/440V 5.5/2.8A Motor 馬達 PP-31041A 2HP 3φ 4P 60HZ 230/460V 5.5/2.7A Motor 馬達 PP-31042 2HP 3φ 60HZ 220/380V 5.5/3.2A 4P Motor 馬達 PP-31043 2HP 3φ...
  • Page 87 MH-1016JA series PART LIST 2014/1/28...
  • Page 88 MH-1016JA series PART LIST 2014/1/28 (右導輪座組)
  • Page 89 MH-1016JA series PART LIST 2013/3/1 SJY-11029 張力調整組 Blade tension adjustment device PART NO. PART NAME PART NAME CHINESE PART SPEC. Q'TY SJY-1102 Blade tension bracket 張力滑板座 SJY-1102A Blade tension adjusting plate 張力調整板 MJA-2022 Guide plate 壓條 SJY-1115 Blade tension adjusting shaft 張力調整螺桿...
  • Page 90 MH-1016JA series PART LIST 2014/1/27 9-11...
  • Page 91 MH-1016JA series PART LIST 2014/1/27 Left Guide Roller Assembly 平面華司 彈簧華司 彈簧華司 9-12...
  • Page 92 MH-1016JA series PART LIST 2014/1/27 M916J-31600 9-13...
  • Page 93 MH-1016JA series PART LIST 2014/1/27 Right Guide Roller Assembly 平面華司 彈簧華司 彈簧華司 9-14...
  • Page 94 MH-1016JA series PART LIST 2013/3/1 MJA-1035 油壓缸組 Lift cylinder 9-15...
  • Page 95 MH-1016JA series PART LIST 2013/3/1 MJA-1035 油壓缸組 Lift cylinder PART NO. PART NAME PART NAME CHINESE PART SPEC. Q'YT MAE-3060 Cylinder rear cover 鋸弓油缸後蓋 MAE-3061 Cylinder front cover 鋸弓油缸前蓋 MAE-3062 Piston 活塞 MAE-3063 Piston rod 活塞桿 MAE-3064 Tube 缸筒 MAE-3065 Shaft 連桿...
  • Page 96 MH-1016JA 9-17...
  • Page 97 MH-1018JA series PART LIST 2013/3/25 9-18...
  • Page 98 MH-1018JA series PART LIST 2013/3/25 底座組 Bed Assembly PART NO. PART NAME Q'YT PART NAME CHINESE PART SPEC. M1018-10000 Bed Assembly 床面組 M1018-30000 Saw bow assembly 鋸弓組 S1018-32500 Lift Cylinder 油壓缸組 AJC-7024 Coolant pump fixed plate 水幫固定蓋 AJC-7017A-CE Base 底座 MJA-1020 Wire rope guide wheel 鋼索導輪...
  • Page 99 MH-1018JA series PART LIST 2012/12/25 9-20...
  • Page 100 MH-1018JA series PART LIST 2013/4/2 床面組 Saw bow assembly PART NO. PART NAME PART NAME CHINESE PART SPEC. Q'TY MJA-1001 床面 MJA-1008B Joint shaft 關節軸 MJA-1010 Movable vise 活動虎鉗 MJA-1011 Fixed vise 固定虎鉗 MJA-1012 Lead screw seat 導螺桿座 MJA-1013 Lead screw ring 導螺桿固定圈...
  • Page 101 MH-1018JA series PART LIST 2013/3/26 鋸弓組 Saw bow assembly 9-22...
  • Page 102 MH-1018JA series PART LIST 2013/3/26 PART NO. PART NAME PART NAME CHINESE PART SPEC. Q'TY M1018-3001 Saw bow 鋸弓 SJY-1113 Idle wheel 上輪 PP-14130 Bearing 軸承 6205Z MAE-2025 Bearing washer 上輪軸墊圈 SJY-1114 Idle wheel shaft 上輪軸 PLA-12-40 Hexagon bolt 外六角頭螺絲 M12*40L PQB-12 Spring Washer...
  • Page 103 2013/5/17 PART NO. PART NAME PART NAME IN CHINESE PART SPEC. Motor 馬達 PP-31041 2HP 3φ 4P 60HZ 220/440V 5.5/2.8A Motor 馬達 PP-31041A 2HP 3φ 4P 60HZ 230/460V 5.5/2.7A Motor 馬達 PP-31042 2HP 3φ 60HZ 220/380V 5.5/3.2A 4P Motor 馬達 PP-31043 2HP 3φ...
  • Page 104 MH-1016JA series PART LIST 2014/1/28 9-25...
  • Page 105 MH-1016JA series PART LIST 2014/1/28 2250L (右導輪座組) 9-26...
  • Page 106 MH-1016JA series PART LIST 2014/1/27 9-27...
  • Page 107 MH-1016JA series PART LIST 2014/1/27 Left Guide Roller Assembly 平面華司 彈簧華司 彈簧華司 9-28...
  • Page 108 MH-1016JA series PART LIST 2014/1/27 M916J-31600 9-29...
  • Page 109 MH-1016JA series PART LIST 2014/1/27 Right Guide Roller Assembly 平面華司 彈簧華司 彈簧華司 9-30...
  • Page 110 MH-1018JA series PART LIST 2013/3/1 SJY-11029 張力調整組 Blade tension adjustment device PART NO. PART NAME PART NAME CHINESE PART SPEC. Q'TY SJY-1102 Blade tension bracket 張力滑板座 SJY-1102A Blade tension adjusting plate 張力調整板 MJA-2022 Guide plate 壓條 SJY-1115 Blade tension adjusting shaft 張力調整螺桿...
  • Page 111 MH-1018JA series PART LIST 2013/3/4 S1018-32500 油壓缸組 Lift cylinder 9-32...
  • Page 112 MH-1018JA series PART LIST 2013/3/4 S1018-32500 油壓缸組 Lift cylinder PART NO. PART NAME PART NAME CHINESE PART SPEC. Q'YT MAE-3060 Cylinder rear cover 鋸弓油缸後蓋 MAE-3061 Cylinder front cover 鋸弓油缸前蓋 MAE-3062 Piston 活塞 MAE-3063 Piston rod 活塞桿 MAE-3064 Tube 缸筒 MAE-3065 Shaft 連桿...
  • Page 113 MH-1018JA 9-34...
  • Page 114 COSEN MACHINERY INDUSTRIAL CO., LTD. 110, CHING-FU STREET, HSIN-CHU, TAIWAN, R. O. C. 886-3-5332143-5 886-3-5348324 e-mail cosen@ms9.hinet.net...

This manual is also suitable for:

Mh-1018ja

Table of Contents

Save PDF