cytiva AxiChrom Original Instructions Manual
  1. Manuals
  2. Brands
  3. cytiva Manuals
  4. Laboratory Equipment
  5. AxiChrom
  6. Original instructions manual

cytiva AxiChrom Original Instructions Manual

Wheel kits
Hide thumbs

Advertisement

Table of Contents

AxiChrom wheel kits
Instructions
Original instructions
cytiva.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the AxiChrom and is the answer not in the manual?

Questions and answers

Related Manuals for cytiva AxiChrom

Summary of Contents for cytiva AxiChrom

  • Page 1 AxiChrom wheel kits Instructions Original instructions cytiva.com...

  • Page 2: Table Of Contents

    General precautions when moving columns ........4 AxiChrom 300-600 wheel kit ............... 6 AxiChrom 300-600 wheel kit components ..............7 Fitting an AxiChrom 300-600 wheel kit ................10 Removing an AxiChrom 300-600 wheel kit ..............13 AxiChrom 800-1000 wheel kit ............. 15 AxiChrom 800-1000 wheel kit components ..............

  • Page 3: Introduction

    AxiChrom 300-1600 columns Operating Instructions (29065430) and in AxiChrom 300-1600 columns User Manual (29099939). This document only describes how to install and use a wheel kit on an AxiChrom™ column. For more information about AxiChrom columns please refer to the user documentation provided with your column.

  • Page 4: General Precautions When Moving Columns

    CAUTION To avoid accidental collisions, use caution when moving columns equipped with wheels by hand. Two or more people may be required to move the column safely. AxiChrom wheel kit Instructions 29145462 AB...
  • Page 5 NOTICE While transporting a 300-600 column, do not pull the handle upward, as the trolley knob may fall out of its position. Lifting the handle will not work as a brake. AxiChrom wheel kit Instructions 29145462 AB...

  • Page 6: Axichrom 300-600 Wheel Kit

    AxiChrom 300-600 wheel kit Introduction This section describes how to fit a wheel kit for use with AxiChrom 300-600 columns. In this chapter Section See page AxiChrom 300-600 wheel kit components Fitting an AxiChrom 300-600 wheel kit Removing an AxiChrom 300-600 wheel kit...

  • Page 7: Axichrom 300-600 Wheel Kit Components

    AxiChrom 300-600 wheel kit components The following image illustrates the main components of the AxiChrom 300-600 column wheel kit. Wheel kit components Part Function Lever Trolley Trolley bar Rear wheels AxiChrom wheel kit Instructions 29145462 AB...
  • Page 8 Holes for fitting rear wheels Pins for locating trolley bar Note: To be able to fit or remove the wheels of an AxiChrom 300-600 column wheel kit, the distance between the floor and the column stand must be in the range 90-110 mm.
  • Page 9 Part Function Trolley knob Slots Safety pin AxiChrom wheel kit Instructions 29145462 AB...

  • Page 10: Fitting An Axichrom 300-600 Wheel Kit

    Fitting an AxiChrom 300-600 wheel kit To be able to use the jack to assemble/disassemble the trolleys and fit or remove an AxiChrom 300-600 column wheel kit the following requirements must be met. • The distance between the floor and the column stand must be between 90-110 mm for AxiChrom 300-600 columns.
  • Page 11 Lower the column by lifting the lever arm. Ensure that the column stands firmly on the wheels before removing the lever. Fit the second pair of rear wheels on the other rear foot by repeating steps 1 to 3 above. AxiChrom wheel kit Instructions 29145462 AB...
  • Page 12 Lift the front of the column by lowering the handle on the trolley. Turn the trolley so it faces forward. Make sure that the column rests fully on the wheels. Screw the foot pads in completely. The column can now be moved. AxiChrom wheel kit Instructions 29145462 AB...

  • Page 13: Removing An Axichrom 300-600 Wheel Kit

    Removing an AxiChrom 300-600 wheel kit When the column has been rolled into position at the intended location, remove the wheel kit from the column as described below. Step Action Adjust all feet until they have the same distance between the floor and stand, 90 to 110 mm.
  • Page 14 Lower the column by lifting the lever arm. Remove the lever. Repeat steps 4 to 6 on the other rear foot. Make sure that the column stands firmly on all feet. Make sure that the column is level before it is taken into operation. AxiChrom wheel kit Instructions 29145462 AB...

  • Page 15: Axichrom 800-1000 Wheel Kit

    AxiChrom 800-1000 wheel kit Introduction This section describes how to fit a wheel kit for use with AxiChrom 800-1000 columns. In this chapter Section See page AxiChrom 800-1000 wheel kit components Fitting an AxiChrom 800-1000 wheel kit Removing an AxiChrom 800-1000 wheel kit...

  • Page 16: Axichrom 800-1000 Wheel Kit Components

    AxiChrom 800-1000 wheel kit components The following images illustrate the main components of the AxiChrom 800-1000 column wheel kit. Wheel kit components Part Function Trolley bar top Lower part Slot AxiChrom wheel kit Instructions 29145462 AB...
  • Page 17 Function Holes for fitting rear wheels Note: To be able to fit or remove the wheels of an AxiChrom 800-1000 column wheel kit, the distance between the floor and the column stand must be in the range 95-135 mm. AxiChrom wheel kit Instructions 29145462 AB...

  • Page 18: Fitting An Axichrom 800-1000 Wheel Kit

    Fitting an AxiChrom 800-1000 wheel kit To be able to use the jack to assemble/disassemble the trolleys and fit or remove an AxiChrom 800-1000 column wheel kit the following requirements must be met. • The distance between the floor and the column stand must be between 95-135 mm for AxiChrom 800-1000 columns.
  • Page 19 Use the handle on the trolley bar to steer it in between the front feet of the column. The top B of the trolley bar should hang on the column stand when positioned. Part Function Trolley bar top Lower part Slot Screw AxiChrom wheel kit Instructions 29145462 AB...
  • Page 20 Make sure that the pin underneath the stand fits inside the slot D of the trolley bar, then tighten the screw E in the image in step 1. Make sure that both screws E are in the correct position. AxiChrom wheel kit Instructions 29145462 AB...
  • Page 21 Ensure that the column rests fully on the wheels. The column can now be moved using a MasterMover or PowerAttack connected to the appropriate connection fitting, respectively, on the front of the trolley bar. AxiChrom wheel kit Instructions 29145462 AB...

  • Page 22: Removing An Axichrom 800-1000 Wheel Kit

    Removing an AxiChrom 800-1000 wheel kit When the column has been rolled into position at the intended location, remove the wheel kit from the column as described below. Step Action Adjust all feet until they have the same distance between the floor and the column stand, within the interval 95-135 mm.
  • Page 23 Fit the trolley bar wheels in the trolley bar storage positions, as shown in the illustration. Fit the rear wheels in the trolley bar storage positions F. Attach the handle to the trolley bar. AxiChrom wheel kit Instructions 29145462 AB...
  • Page 24 Use the handle to retract the trolley bar from the column stand. Make sure that the column stands firmly on all feet. Make sure that the column is level before it is taken into operation. AxiChrom wheel kit Instructions 29145462 AB...

  • Page 25: Axichrom 1200-1600 Wheel Kit

    AxiChrom 1200-1600 wheel kit Introduction This section describes how to fit a wheel kit for use with AxiChrom 1200-1600 columns. In this chapter Section See page AxiChrom 1200-1600 wheel kit components Fitting an AxiChrom 1200-1600 wheel kit Removing an AxiChrom 1200-1600 wheel kit...

  • Page 26: Axichrom 1200-1600 Wheel Kit Components

    AxiChrom 1200-1600 wheel kit components Wheel kit components The following image illustrates the main components of the AxiChrom 1200-1600 column wheel kit (product ordering number 29090400), as well as the moving arm attachment fitting, which has a different product ordering number according to the...
  • Page 27 MasterMover itself must be ordered directly from the supplier. For information about suitable moving equipment and attachment couplings for the various AxiChrom column sizes, see the AxiChrom product pages on the Cytiva website. AxiChrom wheel kit Instructions 29145462 AB...
  • Page 28 The moving arm attachment fitting required is column size dependant and is therefore not included as part of wheel kit 29090400, but must be ordered separately. • The moving arm attachment fitting used with AxiChrom 1600 columns has product ordering number 29091014. •...

  • Page 29: Fitting An Axichrom 1200-1600 Wheel Kit

    Fitting an AxiChrom 1200-1600 wheel kit To be able to use the jack to assemble/disassemble the trolleys and fit or remove an AxiChrom 1200-1600 wheel kit the following requirements must be met. • The distance between the floor and the column stand must be between 160-180 mm for AxiChrom 1200-1600 columns.
  • Page 30 Wrap PTFE around the threads of the attachment hitch fastening bolts before use. • To fit the moving arm attachment fitting to AxiChrom 1200 and 1400 columns: a. Remove the nut from one column flange bolt (A). b. Attach the moving arm attachment fitting by screwing it to the bottom backing plate with the two attachment bolts provided with the moving arm attachment fitting (B and C), as shown in the illustration.
  • Page 31 Step Action • To fit the column attachment hitch to AxiChrom 1600 columns: a. Remove the nuts from two of the column flange bolts (A and B). b. Attach the moving arm attachment fitting by screwing it to the bottom backing plate with the three attachment bolts provided with the moving arm attachment fitting, as shown in the illustration.
  • Page 32 Make sure that the raised mounting socket on top of the wheel trolley is aligned with the corresponding recess (safety pin mounting position) in the column stand. AxiChrom wheel kit Instructions 29145462 AB...
  • Page 33 WARNING Make sure that the wheels are immobilized when fitting a wheel kit, so that the column cannot begin to roll away. AxiChrom wheel kit Instructions 29145462 AB...
  • Page 34 Make sure that the mounting socket on the wheel trolley is aligned with the recess position in the crossbeam. Lower the column onto the front trolley and remove the jack. AxiChrom wheel kit Instructions 29145462 AB...
  • Page 35 Refer to the third party documentation provided with the MasterMover or PowerAttack for instructions on how the moving equipment should be used. AxiChrom wheel kit Instructions 29145462 AB...

  • Page 36: Removing An Axichrom 1200-1600 Wheel Kit

    Step Action Make sure that the wheels of the AxiChrom 1200-1600 wheel kit are immobilized, so that the column cannot begin to roll unexpectedly, before disconnecting the moving equipment from the attachment hitch connection.
  • Page 37 Make sure that the column is level before it is taken into operation. This step is optional. The moving arm can be left attached to the column if it is likely that the column will be moved again. AxiChrom wheel kit Instructions 29145462 AB...
  • Page 38 © 2020 Cytiva All goods and services are sold subject to the terms and conditions of sale of the supplying company operating within the Cytiva business. A copy of those terms and conditions is available on request. Contact your local Cytiva representative for the most current information.

Table of Contents

Save PDF