Nokia NKC-1X Series Assembly And Disassembly Instructions
Hide thumbs
Also See for NKC-1X Series:
- Technical documentation manual (54 pages) ,
- Technical documentation manual (32 pages) ,
- Troubleshooting instructions (34 pages)
Related Manuals for Nokia NKC-1X Series
Summary of Contents for Nokia NKC-1X Series
- Page 1 CCS Technical Documentation NKC-1X Series Transceivers Assembly and Disassembly Instructions Nokia Corporation Issue 1 02/03...
- Page 2 NKC-1X Assembly and Disassembly Instructions CCS Technical Documentation Table of Contents Page No Disassembling the NKC-1X Basic Transceiver............. 3 Assembling the NKC-1X Basic Transceiver ..............9 Nokia Corporation Page 2 Issue 1 02/03...
- Page 3 Place your finger between the A- and D-covers’ snap feature. Note! Do not use a screwdriver in this phase, as it may leave marks on the phone’s mechanics. Lift the ATO module and remove the A-cover. Nokia Corporation Issue 1 02/03 Page 3...
- Page 4 Lift and remove the engine module. Note! The use of gloves is mandatory when removing the engine module in order to prevent fingerprints on the engine. Nokia Corporation Page 4 Issue 1 02/03...
- Page 5 The domes and elastomer connector may damage if touched. Remove the speaker assembly from the C-cover. Note! Handle with care, as the speaker and the springs may damage if touched. Nokia Corporation Issue 1 02/03 Page 5...
- Page 6 Lift the antenna. To remove the battery connector, gently press the connector down- wards from the battery base side of the D-cover until the connector detaches. Note! Do not reuse the battery connector after disassembly. Nokia Corporation Page 6 Issue 1 02/03...
- Page 7 D-cover and gently lift the buzzer from its place. Note! The heat staking features will break during disassembly. However, this will not prevent replacing a new buzzer onto the D-cover. Nokia Corporation Issue 1 02/03 Page 7...
- Page 8 Assembly and Disassembly Instructions CCS Technical Documentation Release the four side locks with a screwdriver. Push the metal deck from the engine side. Note! Do not reuse the metal deck after disassembly. Disassembly completed. Nokia Corporation Page 8 Issue 1 02/03...
- Page 9 All four tabs should snap into the slots of the D-cover. Press the Power key into its place. Press the antenna key into its place. Nokia Corporation Issue 1 02/03 Page 9...
- Page 10 Note! Make sure that the battery connector (white arrow) is below the edges of the D-cover (black arrow) after assembly. Place the buzzer assemble into its place. Use tweezers. Note! Make sure that the buzzer springs stay intact. Nokia Corporation Page 10 Issue 1 02/03...
- Page 11 Note! If the LCD module is to be reused, the use of gloves is manda- tory to prevent fingerprints on the domes and elastomer connector. The domes and elastomer connector may damage if touched. Nokia Corporation Issue 1 02/03 Page 11...
- Page 12 C-cover. Press the D-cover to snap the side locks. Fasten the 4 screws to fix the D- and C-covers. Note! Use the specified screws and torque; 21Ncm/350rpm Place the keymat onto the A-cover. Nokia Corporation Page 12 Issue 1 02/03...
- Page 13 Fasten the 2 screws to fix the A-cover. Note! Use the specified screws and torque; 21Ncm/350rpm. Place the B-cover on the phone. Slide the cover so that the spring snaps the cover into place. Assembly completed! Nokia Corporation Issue 1 02/03 Page 13...
- Page 14 NKC-1X Assembly and Disassembly Instructions CCS Technical Documentation This page was intentionally left blank. Nokia Corporation Page 14 Issue 1 02/03...