Advertisement
Quick Links
Advertisement
Related Manuals for GE CWLSWDMBWF1
Summary of Contents for GE CWLSWDMBWF1
- Page 1 ™ Wire-Free Smart Switch Installation Guide Models CWLSWDMBWF1 CWLSWCCBWF1...
- Page 2 Simple DIY Setup Install Download your Smart the C by GE app your Wire-Free Switch Smart Switch to the C by GE app...
-
Page 3: Compatibility Requirements
Compatibility Requirements Works with C by GE Smart Lights, Plugs, Switches, and Sensors. Not compatible with non-C by GE Smart devices. NOTE: Switch and other C by GE lights, plugs, and switches must be grouped in the same Room/Space in... - Page 4 Let’s Do It INCLUDED Switch Wall Plate 4 Phillips Drywall Adhesive Mounting Screws Anchors Tape YOU’LL NEED Phillips Screwdriver OPTIONAL Tape Measure Drill w/ 7/32 bit Level...
- Page 5 You Got This! And we’re here to help. For in-depth instructional videos and a guided tour through the installation, go to cbyge.com/wirefree-support.
- Page 6 BEFORE YOU DO ANYTHING: Step 1 Location & Mounting Type Decide how you want to mount your switch This switch can be mounted to the wall in two ways, by screws or adhesive tape. Once you determine which install method is best for you, select one of the following setup methods.
- Page 7 STEP 2 - Mounting with adhesive tape Installing Your Switch IMPORTANT Start by removing the clear plastic tab from the back of the switch. 1. Identify where you want to mount your Wire-Free Switch (switches are typically located 48-52” from the floor to the top of the switch). 2.
- Page 8 STEPS 1 & 2 STEPS 3, 4 & 5...
- Page 9 STEP 2 - Mounting with screws/single-gang wallplate Installing Your Switch IMPORTANT Start by removing the clear plastic tab from the back of the switch. 1. Identify where you want to mount your Wire-Free Switch (switches are typically located 48-52” from the floor to the top of the switch). 2.
- Page 10 STEPS 1 & 2 STEPS 3 STEPS 4 & 5...
- Page 11 STEP 2 - Mounting with screws/single-gang wallplate Installing Your Switch IMPORTANT Start by removing the clear plastic tab from the back of the switch. 1. Remove existing wallplate. 2. Get multi-gang wallplate (purchased separately). 3. Use new wallplate to mark the location for holes to be drilled. 4.
- Page 12 STEPS 1 & 2 STEPS 3 STEPS 4, 5 & 6...
- Page 13 Group your Smart Switch to your wire-Free Switch and other the C by GE app C by GE devices you want to control with the switch in the same Room/Space in the C by GE app.
- Page 14 What You Can Do With Your Switch Wire-Free Smart Switch + Smart Bulb • Control lights without leaving your bed or couch • Dim and brighten lights from the switch • Keep switch control entering a room after moving furniture and plugging lamps into different sockets Wire-Free Smart Switch + Smart Plug •...
- Page 15 What You Can Do With Your Switch Wire-Free Smart Switch + Wired Smart Switch • Create 3-way connections without rewiring • Control lights outside a room, like a kitchen light from the hallway • Set up a master on/off switch next to your bed...
-
Page 16: Removing/Replacing The Battery
Removing/Replacing the Battery 1. Remove the switch from the wall. 2. Remove rear housing of the switch using Phillips screwdriver. 3. Slide the battery out, towards the top of the switch. 4. Slide a new battery underneath the contact strap, with the (*) terminal toward the back of the switch. - Page 17 Additional Information and Warnings FCC Compliance Statement Compliance Notice: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
- Page 18 RF Exposure Information: This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons.
- Page 19 This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
- Page 20 WARNING: Chemical Burn Hazard. Keep batteries away from children. This product contains a lithium button/coin cell battery. If a new or used lithium button/coin cell battery is swallowed or enters the body, it can cause severe internal burns and can lead to death in as little as 2 hours.
- Page 21 Like your new C by GE Smart Switch? Share your experience! Leave a review where you purchased the product.