Advertisement
Quick Links
Advertisement
Related Manuals for Alarm.Com Building 36 ADC-T3000
Summary of Contents for Alarm.Com Building 36 ADC-T3000
- Page 1 Alarm.com Smart Thermostat Z-Wave Manual V1.3 June 26, 2019 Building 36 Technologies...
- Page 2 9. Press the Menu (-) Button 10. Select SETTINGS 11. Select NETWORK 12. Select REMOVE 13. Thermostat will display ‘Network Remove In Progress’. 14. The thermostat has been removed successfully when the thermostat displays ‘Network Remove Complete’ Building 36 Technologies An Alarm.com Company...
-
Page 3: Node Information
Z-Wave Plus logo. The 5-digit DSK pin is located beneath the QR Code. The QR code and entire DSK is printed on the thermostat box. During add process, the thermostat shows the 5-digit DSK pin on the thermostat screen. Building 36 Technologies An Alarm.com Company... - Page 4 Code present on the product with a controller providing SmartStart inclusion. No further action is required and the SmartStart product will be added automatically within 10 minutes of being switched on in the network vicinity. Building 36 Technologies An Alarm.com Company...
- Page 5 Highest Granted Security Class Device Reset Locally Highest Granted Security Class Power Level Highest Granted Security Class Association Group Info None Supervision None Security 2 None Transport Service None Basic Highest Granted Security Class Building 36 Technologies An Alarm.com Company...
- Page 6 • 0xE3 Wiring Error • 0xE4 Unexpected Z-Wave Reset • 0xE5 Overcurrent • 0xE6 Unexpected Switch Opened • 0xE7 Unexpected Switch Closed Software Failure with Set when software failure detected. No code software errors are defined. Building 36 Technologies An Alarm.com Company...
- Page 7 • Size 4 bytes 5.1.6 0x06 : Swing (0.0°F to 3°F), 0.5°F increments • Default 0.5°F • Size 4 bytes 5.1.7 0x07 : Overshoot (0.0°F to 3°F), 0.5°F increments • Default is 0.0°F • Size 4 bytes Building 36 Technologies An Alarm.com Company...
- Page 8 5.1.16 0x10 : Minimum Heat Setpoint (35°F - 95°F), 1°F increments • Default 35°F • Size 4 bytes 5.1.17 0x11 : Maximum Cool Setpoint (50°F - 95°F), 1°F increments • Default 95°F • Size 4 bytes Building 36 Technologies An Alarm.com Company...
- Page 9 • Size 1 byte 5.1.21 0x15 : RESERVED 5.1.22 0x16 : RESERVED 5.1.23 0x17 : Temperature Display Units (Fahrenheit | Celsius) • 0x00 - Celsius • 0x01 - Fahrenheit (Default) • Size 1 byte Building 36 Technologies An Alarm.com Company...
- Page 10 • Size 1 byte 5.1.27 0x1B : Battery Alert Threshold Low (0-100%) • Default 30% • Size 1 byte 5.1.28 0x1C : Battery Alert Threshold Very Low (0-100%) • Default 15% • Size 1 byte Building 36 Technologies An Alarm.com Company...
- Page 11 5.1.32 0x20 : Cool Differential (1.0°F to 10.0°F), 0.5°F increments • Default 3.0°F • Size 4 bytes 5.1.33 0x21 : Temperature Reporting Threshold (0.5°F to 2.0°F), 0.5°F increments • Default 1.0°F • Size 4 bytes 5.1.34 0x22 : RESERVED Building 36 Technologies An Alarm.com Company...
- Page 12 5.1.36 0x24 : C-Wire Power Thermistor Offset • Default -2.0°F • Size 4 byte 5.1.37 0x25 : Run Fan With Auxiliary Heat • 0x00 - Disabled (DEFAULT) • 0x01 - Enabled • Size 1 byte Building 36 Technologies An Alarm.com Company...
- Page 13 Bit 28 – Display units (C/F) o Bit 29 – Heat Fuel Type o Bit 30 – Humidity Control Mode o Bit 31 – Humidity Control Setpoints • Default is 0xFFFFFFFF • Size 4 byte Building 36 Technologies An Alarm.com Company...
- Page 14 5.1.45 0x2D : Heat Pump Expire (0 to 2880 minutes) • Default is 0 minutes • Size 2 byte 5.1.46 0x2E : Dehumidify by AC Offset (0°F to 10°F) 1.0°F increments • Default is 3°F • Size 4 bytes Building 36 Technologies An Alarm.com Company...
- Page 15 • 0x03 – Only activate vent when the thermostat operating state is cooling. • 0x04 – Only activate the vent when the thermostat operating state is heating or cooling. • Default is 0x04 • Size 1 byte Building 36 Technologies An Alarm.com Company...
- Page 16 • Set PTO Harvest Interval for Relay MCU energy harvesting. • 0x00 – Off • 0x02 – 4 Milliseconds • 0x03 – 8 Milliseconds • 0x04 – 16 Milliseconds • 0x05 – 32 Milliseconds • Default is 16 Milliseconds • Size 1 bytes Building 36 Technologies An Alarm.com Company...
- Page 17 1.5dB power step. Byte 0 is the LBT threshold for channel 0 and Byte 1 is the LBT threshold for channel 1. • Valid Range in decimal: 64 (-65dB) to 78 (-44dB) • Default is decimal 78 (-44dB) for both channels • Size is 2 byte Building 36 Technologies An Alarm.com Company...
- Page 18 • 0x01 – Only humidify when the thermostat operating state is heating, when in heat mode or when heating in auto mode. When in any other thermostat mode, the thermostat will humidify whenever it is necessary. • Default is 0x01 • Size 1 byte Building 36 Technologies An Alarm.com Company...
- Page 19 • Notification Report : See Notifications section for more information. • Device Reset Locally Report : When thermostat is set to default it will notify all nodes on in the lifeline association group. Building 36 Technologies An Alarm.com Company...
- Page 20 Fahrenheit and increase the heat setpoint by 3 degrees Fahrenheit. If the setpoint change causes the setpoints to exceed the minimum or maximum setpoint values, the setting is ignored. The minimum setpoint is 35F and the maximum is 95F. Building 36 Technologies An Alarm.com Company...
Need help?
Do you have a question about the Building 36 ADC-T3000 and is the answer not in the manual?
Questions and answers