Huawei VPT300 Installation And Commissioning Manual

Intelligent camera (single-vpt300)

Hide thumbs Also See for VPT300:

Product overview (23 pages)

Table Of Contents

Table of Contents

Quick Links

Download this manual

VPT300 Intelligent Camera

V500R003C10

Installation and Commissioning

Guide（Single-VPT300）

Issue

Date

2020-02-11

HUAWEI TECHNOLOGIES CO., LTD.

Table of Contents

Summary of Contents for Huawei VPT300

Page 1 VPT300 Intelligent Camera V500R003C10 Installation and Commissioning Guide（Single-VPT300） Issue Date 2020-02-11 HUAWEI TECHNOLOGIES CO., LTD.
Page 2 Notice The purchased products, services and features are stipulated by the contract made between Huawei and the customer. All or part of the products, services and features described in this document may not be within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information, and recommendations in this document are provided "AS IS"...
Page 3: Table Of Contents
7 Adjusting Camera Parameters................... 26 8 Testing VPT300 Tracking..................... 28 A Calibrating the Camera....................... 29 B Upgrading the Camera Software..................35 C Using Commands to Enable VPT300 Tracking in Idle State........41 Issue 04 (2020-02-11) Copyright © Huawei Technologies Co., Ltd.
Page 4: Installing The Camera
VPT300 Intelligent Camera Installation and Commissioning Guide（Single- VPT300） 1 Installing the Camera Installing the Camera Issue 04 (2020-02-11) Copyright © Huawei Technologies Co., Ltd.
Page 20: Verifying The Installation
After the installation is complete, check the following to ensure the camera's tracking performance: ● Ensure that the bottom of the VPT300 base is 1.5 m to 1.7 m (4.9 ft to 5.6 ft) above the ground. ● Remove the protective film (as shown in...
Page 21 VPT300 Intelligent Camera Installation and Commissioning Guide（Single- VPT300） 2 Verifying the Installation Figure 2-2 Mounting the VPT300 on a flat surface Issue 04 (2020-02-11) Copyright © Huawei Technologies Co., Ltd.
Page 22: Logging In To The Web Interface Of An Endpoint
3 Logging In to the Web Interface of an Endpoint Logging In to the Web Interface of an Endpoint Step 1 Connect the VPT300, TE endpoint, and computer, and ensure that they can communicate with each other, as shown in Figure 3-1.
Page 23 Disable, the endpoint's web interface is inaccessible. If Web login is set to Wi-Fi only, you can access the endpoint's web interface only from the computer that connects to the Wi-Fi hotspot on the endpoint. ----End Issue 04 (2020-02-11) Copyright © Huawei Technologies Co., Ltd.
Page 24: Setting Video Input Parameters
Step 2 Set Camera type to VPT300 and Serial port to None, as shown in Figure 4-1. Generally, the VPT300 uses the 1 MAIN IN port to connect to an endpoint. If another port is used, configure that port. Figure 4-1 Setting video input parameters Step 3 Click Save.
Page 25: Viewing The Camera Software Version
Step 2 View the camera software version. Table 5-1 lists the software version requirements. Table 5-1 Camera software version requirements Camera Required Software Version VPT300 VPT300 V500R003C10SPC200 and later VPC600 C620C00SPC500 and later Issue 04 (2020-02-11) Copyright © Huawei Technologies Co., Ltd.
Page 26 Installation and Commissioning Guide（Single- VPT300） 5 Viewing the Camera Software Version If the camera software version does not meet the requirements, upgrade the camera software. For details, see B Upgrading the Camera Software. ----End Issue 04 (2020-02-11) Copyright © Huawei Technologies Co., Ltd.
Page 27: Enabling Vpt300 Tracking In Idle State
Figure 6-1. Figure 6-1 Enabling VPT300 tracking ● If Enable VPT300 tracking when idle is not available on the web interface of the TE endpoint, use commands to enable VPT300 tracking. For details, see C Using Commands to Enable VPT300 Tracking in Idle State.
Page 28 VPT300 Intelligent Camera Installation and Commissioning Guide（Single- VPT300） 6 Enabling VPT300 Tracking in Idle State Step 3 Click Save. ----End Issue 04 (2020-02-11) Copyright © Huawei Technologies Co., Ltd.
Page 29: Adjusting Camera Parameters
7 Adjusting Camera Parameters Adjusting Camera Parameters Step 1 Choose Device Control > Device Control and click the Camera parameters adjustment tab. Step 2 In the VPT300 Settings area, set VPT300 parameters, as shown in Figure 7-1. Table 7-1 describes the parameters.
Page 30 VPT300 automatically rotates to the direction in which voice comes. Sensitivity Select the sensitivity for the VPT300's voice tracking function. That is, the VPT300 takes close-up video images of a speaker after the speaker talks for the following duration: ●...
Page 31: Testing Vpt300 Tracking
8 Testing VPT300 Tracking Testing VPT300 Tracking Table 8-1 describes how to test VPT300 tracking and troubleshoot problems. When the VPT300 is in a tracking test, ensure a quiet environment. Table 8-1 Testing VPT300 tracking Test Method Test Result Troubleshooting ●...
Page 32: A Calibrating The Camera
Installation and Commissioning Guide（Single- VPT300） A Calibrating the Camera Calibrating the Camera Step 1 Log in to the VPT300 using SSH. Run the PuTTY software on the local computer. The PuTTY Configuration window is displayed, as shown in Figure A-1.
Page 33 Enter the password (Change_Me by default) and press Enter. The command- line interface is displayed. – If you forget the login password, press and hold the RESET button on the VPT300 for 10s when the VPT300 is running to factory reset it. After the factory reset, all the settings are restored to the default settings.
Page 34 Figure A-3 White box turns green Step 5 Continue observing the image. When the second white box appears, show the face in the white box, as shown in Figure A-4. Issue 04 (2020-02-11) Copyright © Huawei Technologies Co., Ltd.
Page 35 Step 8 Face the camera lens and do not move until the third white box turns green. Step 9 After the three white boxes turn green, calibration calculation is started. If the calibration is successful, a green box blinks, as shown in Figure A-5. Issue 04 (2020-02-11) Copyright © Huawei Technologies Co., Ltd.
Page 36 ● If the calibration fails, a red box blinks. In this case, perform the preceding steps again. Step 10 Run the mnt reboot command or press the power switch at the rear of the VPT300 to restart the VPT300 for the calibration to take effect. Figure A-6 shows the position of the power switch.
Page 37 VPT300 Intelligent Camera Installation and Commissioning Guide（Single- VPT300） A Calibrating the Camera Figure A-6 Position of the power switch on the VPT300 ----End Issue 04 (2020-02-11) Copyright © Huawei Technologies Co., Ltd.
Page 38: B Upgrading The Camera Software
Installation and Commissioning Guide（Single- VPT300） B Upgrading the Camera Software Upgrading the Camera Software Step 1 Connect the VPT300, TE endpoint, and computer, and ensure that they can communicate with each other, as shown in Figure B-1. Figure B-1 VPT300 connection diagram Step 2 Log in to the web interface of the TE endpoint.
Page 39 VPT300 Intelligent Camera Installation and Commissioning Guide（Single- VPT300） B Upgrading the Camera Software Figure B-2 Adjusting VPT300 parameters Table B-1 VPT300 parameter description Parameter Description Setting Connection type IP address obtaining Set this parameter based mode of the VPT300. on the site requirements.
Page 40 Step 5 Choose Maintenance > Diagnostics. In the Network Test area, enter the IP address of the VPT300 and click Start, as shown in Figure B-3, to test that the TE endpoint can communicate with the VPT300.
Page 41 + Version number , for example, TE60 V600R006C00SPC800. Download and decompress the endpoint software package to extract the upgrade tool UpgMaster.exe. Step 8 Copy VPT300.dat and C620.dat to the same directory as UpgMaster.exe, as shown in Figure B-4.
Page 42 VPT300 Intelligent Camera Installation and Commissioning Guide（Single- VPT300） B Upgrading the Camera Software Figure B-4 Copy VPT300.dat and C620.dat to the same directory as UpgMaster.exe Step 9 Double-click UpgMaster.exe and set the parameters, as shown in Figure B-5. Figure B-5 Upgrading the VPT300 Step 10 Click Upgrade and enter the upgrade password (Change_Me by default) to upgrade the VPT300.
Page 43 B Upgrading the Camera Software Figure B-6 Upgrading the VPC600 ● When upgrading the VPC600, you also need to select VPT300 for Product Type. ● The two VPC600s are upgraded at the same time, and the upgrade takes about 30 minutes.
Page 44: C Using Commands To Enable Vpt300 Tracking In Idle State
VPT300 Intelligent Camera Installation and Commissioning Guide（Single- C Using Commands to Enable VPT300 Tracking in VPT300） Idle State Using Commands to Enable VPT300 Tracking in Idle State Step 1 Enable Telnet or SSH login. Log in to the web interface of the TE endpoint. For details, see...
Page 45 VPT300 Intelligent Camera Installation and Commissioning Guide（Single- C Using Commands to Enable VPT300 Tracking in VPT300） Idle State Step 8 Enter mnt reboot and press Enter. ----End Issue 04 (2020-02-11) Copyright © Huawei Technologies Co., Ltd.

This manual is also suitable for:

V500r003c10

Huawei VPT300 Installation And Commissioning Manual

Quick Links

Related Manuals for Huawei VPT300

Summary of Contents for Huawei VPT300

This manual is also suitable for:

Table of Contents